• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.816-821
• /
• 2013

This case study presents a practical method to reduce resonant vibration of generator-motor set. The generator is driven at 1800rpm by induction integral motor. The vibration is below alarm limits, but the dominant frequency of vibration is sub-synchronous and close to that of bearing fault signal in spite of new bearings. To find an mechanism of abnormal vibration, ODS and Modal analysis is carried out. The measured modal characteristics were compared with those of FE Analysis. The ODS mode at rated speed is consistent with system natural frequency mode that is excited by bearings. To reduce vibration level, the isolation mount at system base is changed with new rubber mount for lower natural frequency.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.228-230
• /
• 2005

In this paper, we address an active vibration control system, which suppresses the vibration engaged by magnetically levitated stage. The stage system consists of a levitating platen with four permanent magnetic linear synchronous motors in parallel. Each motor generates vertical force for suspension against gravity and propulsion force horizontally as well. This stage can generate six degrees of freedom motion via the vertical and horizontal forces. In the stage system, which represents the settling-time critical system, the motion of the platen vibrates mechanically. We designed an active vibration control system for suppressing vibration due to the stage moving. The command feedforward with inertial feedback algorithm is used for solving stage system's critical problems. The components of the active vibration control system are accelerometers for detecting stage tables's vibrations, a digital controller with high precise signal converters. and electromagnetic actuators.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.312.2-312
• /
• 2002

Theoretical analysis of transient torsional vibration was started from early 1960's for high power synchronous motor application. Especially, its simulation and measuring techniques in marine engineering field have been steadily studied by manufacturers of flexible coupling and designers of four stroke marine diesel engine. In this paper, the simulation method of transient torsional vibration of four stroke marine diesel engine using the Newmark method are introduced. (omitted)

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.44-50
• /
• 2002

Theoretical analysis on the transient torsional vibration was started from early 1960's for high power synchronous motor application. As for marine engineering, simulation and measuring techniques of transient torsional vibration have been steadily studied by manufacturer of flexible coupling and designer of four stroke marine diesel engine. In this paper, the simulation method of transient torsional vibration for four stroke marine diesel engine application using Newmark method is introduced.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.179-183
• /
• 1999

Rubbing occurs when a rotating element comes in contact with a stationary element. In the steam turbines, the rotating element is the rotor while the stationary elements are usually the oil deflectors and packing seals. Rubbing phenomenon may be often obseued on a new or rebuilt machine rather than on a machine that has been operating for several months or years. Rubbing in the turbine has been classified into two modes by the operating conditions: 1) start up or shut down, 2) steady state. At start up or shut down operation, rubbing produces synchronous whirl vibration, which are caused by thermal bow of the shaft due to localized heating on the shaft surface. While subsynchronous whirl vibration is caused by partial rubbing during the steady state operation. In this paper, the two case studies of troubleshooting for excessive vibration caused by rubbing in the actual steam turbines are investigated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.830-835
• /
• 2002

Theoretical analysis about transient torsional vibration was started from early 1960's for high power synchronous motor application. Especially, its simulation and measuring techniques in marine engineering field have been steadily studied by classification societies and designers of large diesel engine. In this paper, the simulation method of transient torsional vibration of two stroke low speed diesel engine using the Newmark method are introduced.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.84-89
• /
• 2014

Data-driven method for fault diagnostics system often use machine learning technique. To use such technique proper signal processing should be implemented such as time synchronous averaging (TSA) for ball bearing systems. However, for journal bearing diagnostics systems not much has been researched, and yet a proper signal processing method has not been studied. Therefore, in this research an optimal datum unit for a reliable journal bearing diagnostics system along with angular resampling process is being suggested. Before extracting time and frequency domain features, angular resampling is applied to each cycle of vibration data. As to preserve the characteristics of vibration signal, averaging method is replaced by finding the optimal datum unit which strengthens statistical characteristics of vibration signal. Then 20 features were extracted for various cases, and those features are being evaluated by two criteria, separability and classification accuracy.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.935-937
• /
• 2004

This paper is proposed vibration minimize method of slotted PMLSM which is designed to minimize detent force. For improvement of operational performance by changing velocity profile to reducing the vibration at discontinuous section of acceleration curve in this paper, proter type machine is made, the vibration is compared general trapezoid velocity profile with vibration minimization velocity profile.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.6
• /
• pp.75-84
• /
• 2014

A linear synchronous motor (Linear Synchronous Motor, under LSM) is suitable for Maglev train. This is 500km/h or more for running high-speed propulsion system of high-efficiency, high-output characteristics. Also, as high-speed running, it is needed solution to reduce output ripple component cause bad riding like noise and vibration. So this paper was designed 500km/h-class Maglev train and analyzed characteristics of the LSM base model using finite element analysis method. Further, improved model is designed to improve characteristics of thrust and levitation force by enforcing design parameters analysis and sensitivity analysis. And it was applied skew on field in order to reduce the ripple component still remaining. Skew interpretation of the two-dimensional is proposed and this is verified by carrying out three-dimensional finite element analysis comparing two values. It proved to be valid of skew of the two-dimensional analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.132-139
• /
• 2008

The blade vibration problem of bladed disk is the most critical subject to consider since it directly affects the stable performance of the engine as well as life of the engine. Especially, due to complicated vibration pattern of the bladed disk, more effort was required for vibration analysis and test. The research of measuring the vibration of the bladed disk, using NSMS(Non-intrusive stress measurement) instead of Aeromechanics testing method requiring slip ring or telemetry system with strain gauge, was successful. These testing can report the actual stresses seen on the blades; detect synchronous resonances that are the source of high cycle fatigue (HCF) in blades; measure individual blade mis-tuning and coupled resonances in bladed disks. In order to minimize the error being created due to heat expansion, the tip timing sensor is installed parallel to the blade trailing edge, yielding optimal result. Also, when working on finite element analysis, the whole bladed disk has gone through three-dimensional analysis, evaluating the family mode. The result of the analysis matched well with the test result.