• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.6
• /
• pp.129-135
• /
• 2015

This paper shows significant methods that improve the lifespan of LED modules as well as efficiently using an aluminum heat-sink for LED module in high power. It proposes a method that raises stability and lifespan to protect LED modules and the power unit when the LED module has been used for a long hours at high temperatures. During the research, we applied a method of pulse-width modulation (PWM) in order to prevent the phenomenon that the entire power of a system is turned off and the lifespan is reduced when the LED nodule reacts to the high temperatures. To protect the LED module and SMPS based on high efficiency, a temperature sensor is attached underneath the circuit board and the sensor measures the temperature of circuit board when the LED module is powered on. The electrical power connected to SMPS is controlled by PWM when the temperature of the LED module reaches a particular temperature.

• Proceedings of the KIEE Conference
• /
• 1990.07a
• /
• pp.387-392
• /
• 1990

In this papers, SPICE which is widely used in analysis of general circuit and simulation in electric and electrical field is applied to DC-DC converter. Be selected Forward which is widely used as SMPS(Switched Mode Power Supply) amang DC-DC converter, and showed the aveformer, we know that the converter is operated in normal. Including the control circuit in converter, by controlling the duty ratio of switch, we know that the output voltages is staple from the transient state of convwrter. Also, comparing SPICE simulation with experiment, the validity of simulate is showed.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.28B no.5
• /
• pp.411-420
• /
• 1991

In this paper, SPICE program which is widely used in analysis of general circuit on electronic and electrical field has been applied to DC-DC converter. We have selected Forward type which is widely used us SMPS(Switched Mode Power Supply) of various electronic equipments, and have confirmed the waveforms of circuit operation, transfer of energy and resetting in transformer. And the procedure which the output voltage of converter, including the control circuit, has been stabilized from the transient state to the steady state by controlling the duty ratio of switch is presented. We have compared SPICE simulation with experiment and have verified the validity of SPICE simulation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.4
• /
• pp.425-432
• /
• 2007

This paper describes a development of ship's refer-container remote monitoring system(RRMS). This system consists of Master, repeater with a switched mode power supply(SMPS) and slave terminal. Slave terminal is composed of wireless MODEM and microprocessor part, checks its conditions like temperature. humidity & etc through the interrogate port(IP) of refer-container. and transmits their data to master. Repeater's role is that connect so that signal which is transmitted from Slave Terminal by Master may not receive electric wave interference by container boxes. We verify the effectiveness of proposed system through the experimental works in container yard and ship.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.106-108
• /
• 2002

SMPS는 스위칭을 통해 전력을 변환하므로 높은 dv/dt 및 di/dt 특성을 갖게 된다. 이러한 스위칭특성으로 인해 발생하는 EMI (Electromagnetic Interference) 노이즈는 기기 내부 또는 외부에 간섭을 일으킨다. 미국의 FCC (Federal Communications Commission) 및 유럽 의 CISPR(International Special Committee on Radio Interference) 등의 규정을 만족시키기 위해서 전도성 노이즈에 대한 충분한 이해와 해석이 필요하다. 본 연구는 SMPS에서의 EMI/EMC 대책 구현에 앞서, 전도성노이즈의 기본개념 및 발생/결합 경로를 분석하고 실제로 노이즈를 측정한다. 측정을 위해 Boost 컨버터가 제작/사용된다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.6 s.360
• /
• pp.19-27
• /
• 2007

This paper presents power supply-insensitive Gbps low power LVDS I/O circuits. The proposed LVDS I/O has been designed and simulated using 1.8V, $0.18\;{\mu}m$ TSMC CMOS Process. The LVDS I/O includes transmitter and receiver parts. The transmitter circuits consist of a differential phase splitter and an output stage with the switched capacitor common mode feedback(SC-CMFB). The differential phase splitter generates a pair of differential signals which provides a balanced duty $cycle(50{\pm}2%)$ and phase difference$(180{\pm}0.2^{\circ})$ over a wide supply voltage range. Also, $V_{OD}$ voltage is 250 mV which is the smallest value of the permissible $V_{OD}$ range for low power operation. The output buffer maintains the required $V_{CM}$ within the permissible range$(1.2{\pm}0.1V)$ due to the SC-CMFB. The receiver covers a wide input DC offset $range(0.2{\sim}2.6\;V)$ with 38 mV hysteresis and Produces a rail-to-rail output over a wide supply voltage range. Beside, the designed receiver has 38.9 dB gain at 1 GHz, which is higher than conventional receivers.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.1
• /
• pp.81-85
• /
• 2012

This paper presents a wideband and low-noise direct conversion front-end receiver supporting VHF and UHFbands simultaneously. The receiver iscomposed of a low-noise amplifier (LNA), a down conversion quadrature mixer, and a frequency divider by 2. The cascode configuration with the resistor feedback is exploited in the LNA to achieve a wide operating bandwidth. Four gainstep modesare employed using a switched resistor bank and a capacitor bank in the signal path to cope with wide dynamic input power range. The verticalbipolar junction transistors are used as the switching elements in the mixer to reduce 1/f noise corner frequency. The proposed front-end receiver fabricated in 0.18 ${\mu}m$ CMOS technology shows very low minimum noise figureof 1.8 dB and third order input intercept pointof -12dBm inthe high-gain mode of 26.5 dBmeasured at 500 MHz.The proposed receiverconsumeslow current of 20 mA from a 1.8 V power supply.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.4
• /
• pp.22-27
• /
• 2020

In this paper, a generalized efficiency equation was proposed to estimate the internal loss of the SMPS (switched-mode power supply) with 3 variables. The first variable was an internal loss not related to the load current such as auxiliary power, the second was a loss proportional to the current such as diode loss, and the third was a loss proportional to square of the current such as conduction loss. Especially, theoretical internal losses of the totem pole bridgeless PFC which is widely used for high efficiency SMPS were expressed as output function to compare generalized efficiency equation. In addition, in order to reduce the conduction loss of the switch, when a multiple switch were paralleled, the correlation with the efficiency was analyzed and shown as a graph. In order to confirm the degree of the parallel switch structure on the efficiency improvement, a 2kW class totem pole bridgeless PFC was constructed and the effectiveness of the analysis was confirmed by comparing the generalized efficiency equation and theoretical loss analysis results with experimental data.

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.515-517
• /
• 2008

현재 가동 중인 원자적발전소 계측제어설비의 전원공급기를 살펴보면 인버터 또는 별도의 교류를 입력전원으로 사용한다. 직류 전원공급기들은 설비의 중요도예 따라 이중화로 구성된 설비도 있고 그렇지 않은 기기나 설비도 있다. 이중화로 구성된 전원공급기라 해도 교류 입력전원이 동일하다면 교류 입력이 상실될 때 이중화로 구성된 직류전원도 상실되어 관련계통의 가동이 정지된다. 이러한 문제점을 해결하기 위해서는 각기 다른 교류입력전원으로 동작되는 이중화전원공급기로 구성되는 것이 가장 바람직하다. 본 연구개발의 목적은 두 종의 설비에 소요되는 3종의 직류전원 공급기를 원자력 안정성등급으로 국산화하는 연구이다. 기존 제품들은 3종 모두 리니어 방식의 제품이지만, 방사선감시 계통 현장제어기의 5V로직 전원공급기와 공정제어계통 전원공급자는 전력변환효율이 높고 소형, 정량화가 가능한 SMPS(Switched Mode Power Supply) 방식으로 개발하였다. 방사선감시계통 현장제어기의 PCA(Printed Circuit Assembly) 저전압공급기는 다양한 종류의 출력전압과 저 전류형이므로 안정성 면에서 동일한 형식의 리니어 방식으로 개발하였으며 3종류 모두 출력용량을 20% 이상 향상시켰다. 또한, 논문을 통해 SMPS 방식의 전원공급기의 핵심 부품인 Control Module을 Hybrid IC형으로 자체 설계하여 성능이 우수한 제품을 지속적으로 생산할 수 있는 기틀을 마련하고자 한다.

• Journal of the Korean Society of Safety
• /
• v.36 no.2
• /
• pp.10-17
• /
• 2021

This paper presents the robust design of each component used in the development of an induction bolt heating system for dismantling the high-temperature high-pressure casing heating bolts of turbines in power plants. The induction bolt heating system comprises seven assemblies, namely AC breaker, AC filter, inverter, transformer, work coil, cable, and CT/PT. For each of these assemblies, the various failure modes are identified by the failure mode and effects analysis (FMEA) method, and the causes and effects of these failure modes are presented. In addition, the risk priority numbers are deduced for the individual parts. To ensure robust design, the insulated-gate bipolar transistor (IGBT), switched-mode power supply (SMPS), C/T (adjusting current), capacitor, and coupling are selected. The IGBT is changed to a field-effect transistor (FET) to enhance the voltage applied to the induction heating system, and a dual-safety device is added to the SMPS. For C/T (adjusting current), the turns ratio is adjusted to ensure an appropriate amount of induced current. The capacitor is replaced by a product with heat resistance and durability; further, coupling with a water-resistant structure is improved such that the connecting parts are not easily destroyed. The ground connection is chosen for management priority.