• Journal of Power Electronics
• /
• v.12 no.5
• /
• pp.723-730
• /
• 2012

This paper presents a new ZVS single phase bridgeless (Power Factor Correction) PFC, using an active clamp to achieve zero-voltage-switching for all main switches and diodes. Since the presented PFC uses a bridgeless rectifier, most of the time, only two semiconductor components are in the main current path, instead of three in conventional single-switch configurations. This property significantly reduces the conduction losses,. Moreover, zero voltage switching removes switching loss of all main switches and diodes. Also, auxiliary switch turns on zero current condition. The presented converter needs just a simple non-isolated gate drive circuitry to drive all switches. The eight stages of each switching period and the design considerations and a control strategy are explained. Finally, the converter operation is verified by simulation and experimental results.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.505-507
• /
• 2008

A conventional active-clamp forward (ACF) converter is a favorable candidate in low-to-medium power applications. However, the switches suffer from high voltage stress, i.e., sum of the input voltage and the reset capacitor voltage. Therefore, it is not suitable for high input voltage applications such as a front-end converter of which the input voltage is about 400-$V_{dc}$. To solve this problem, three-switch ACF (TS-ACF) converter, which employs two main switches and one auxiliary switch with low voltage stress, is proposed. Utilizing low-voltage rated switches, the proposed converter is promising for high input voltage applications with high efficiency and low cost.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.400-403
• /
• 2000

This paper deals with the active clamp ZVS flyback converter for semiconductor plasma etching system. The proposed converter has the characteristics of the good power facter low switching noise and efficiency improvement. The characteristics are verified through simulation results. Furthermore the ringing effect due to output capacitance of the main switch can be eliminated by use of active clamp circuit.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1235-1238
• /
• 2004

This paper presents the large-signal transient analysis of a self-driven active-clamp forward converter, eliminating the extra drive circuit for the active clamp switch. The operation principle of the converter was presented and experiential results were used to verify the analyzed results. A 50-W prototype converter built and tested it. From the tested results, input transient response and load transient response of the converter were established.

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1445-1453
• /
• 2017

In this study, a new zero-voltage transition (ZVT) buck converter with coupled inductor using a synchronous rectifier and a lossless clamp circuit is proposed. The regular buck converter with tapped inductor has extended duty cycle for high step-down applications. However, the leakage inductance of the coupled inductor produced considerable voltage spikes across the switch. A lossless clamp circuit is used in the proposed converter to overcome this problem. The freewheeling diode was replaced with a synchronous rectifier to reduce conduction losses in the proposed converter. ZVT conditions at turn-on and turn-off instants were provided for the main switch. The synchronous rectifier switch turned on under zero-voltage switching, and the auxiliary switch turn-on and turn-off were under zero-current condition. Experimental results of a 100 W-100 kHz prototype are provided to justify the validity of the theoretical analysis. Moreover, the conducted electromagnetic interference of the proposed converter is measured and compared with its hard-switching counterpart.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.809-819
• /
• 2017

In this paper, a new coupled inductor DC-DC converter with a high step-up voltage gain is proposed. It is developed from a clamp-mode coupled-inductor boost converter by incorporating an additional capacitor and diode. The proposed converter is able to achieve the higher voltage gain, while still retaining the switch voltage clamp property of its predecessor. In the paper, operation and analysis of the proposed converter are described. Experimental results from a prototype converter are presented to verify the validity of the analysis. The prototype circuit attains the highest efficiency of 92.8%.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.110-113
• /
• 1993

The MOSFET synchronous rectification in the Active-Clamp Forward converter is presented. The Active-Clamp Forward converter has little dead time during the off time of the main switch and it is suitable for the MOSFET synchronous rectification comparing to the other Forward converter topologics. Using the MOSFET synchronous rectification on the Active-Clamp Forward converter with 3.3[V] output and 500[kHz] switching frequency, the improvement of efficiency is achieved comparing with the conventional Schottky barrier diode rectification.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.3
• /
• pp.31-39
• /
• 2012

This paper presents a high efficiency coupled inductor boost DC-DC converter that uses a simple clamp circuit and the coupled inductor and thus overcomes output voltage limit of the conventional boost converter. The proposed converter solves problems of voltage stress of the power semiconductor switch and reverse recovery of the output diode using a simple clamp circuit composed of a diode and a capacitor, and thus the converter improves its total efficiency. In this paper, the operational principle of the proposed converter is explained by each mode and then a design example for the prototype converter based on the explanation is shown. And good performance of the proposed converter is verified through experimental results of the prototype converter that is implemented with the designed circuit parameters.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.8
• /
• pp.517-524
• /
• 2004

In this paper, a novel zero-voltage-switching(ZVS) resonant DC-DC converter is proposed. It is composed of two symmetrical active-clamped circuits, the converter can be achieve ZVS in each switches. Also, active clamp capacitor ratios($\alpha$) of proposed circuit can be reduce a peak stress of switching voltage for each main switch. Simulation results using Pspice 9.2 ver and $C^{++}$ characteristic analysis show a provement for the validity of theoretical analysis. The analysis of the proposed Current-Fed Push Pull type DC-DC converter is generally described by using normalized parameter, and achieved an evaluated characteristic values which is needed to design a circuit. We confirm a rightfulness theoretical analysis by comparing a theoretical values and experimental values obtained from experiment using MOSFET as switching devices.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.520-522
• /
• 2008

A novel two-switch active clamp forward converter suitable for high input voltage applications is proposed. The main advantage of the proposed converter, compared to the conventional active forward converters, is that circuit complexity is reduced and the voltage stress of the main switches is effectively clamped to either the input voltage or the clamping capacitor voltage by two clamping diodes without limiting the maximum duty ratio. Also, the clamping circuit does not include additional active switches, so a low cost can be achieved without degrading the efficiency. Therefore, the proposed converter can feature high efficiency and low cost for high input voltage applications. The operational principles, features, and design considerations of the proposed converter are presented in this paper. The validity of this study is confirmed by the experimental results from a prototype with 200W, 375V input, and 12V output.