• 한국수자원학회논문집
• /
• 제35권1호
• /
• pp.13-24
• /
• 2002

본 연구에서는 역학적으로 실질적이면서도 단순화된 방법으로 폭풍과 같은 악후시에 임의의 해안단면에서 발생하는 소상파의 수동학적 거동에 대한 예측모델을 개발하고자 한다. 실제 크기의 폭풍과 조건하에서 사구의 침식을 모의하기 위해 수행된 대형조파수조 실험에서 계측된 실험자료가 모델 개발을 위해서 활용된다. 일반적으로 본 모델은 해안종단방향에서의 소상파의 파고, 속도 및 주기의 변화를 예측할수 있음을 보인다. 정량적으로 보다 나은 소상파 변수들에 대한 예측은 유의 소상파고가 영이 되는 해빈면의 높이, ymax에 대한 예측향상을 통하여 이루어질수 있다.

• 유공압시스템학회논문집
• /
• 제2권1호
• /
• pp.1-8
• /
• 2005

Recently, swash plate type hydraulic axial piston motors/pumps are being extensively used in the world, because of simple design, light weight and effective cost. Structural problem of the swash plate type motor/pump is that tilting angle of swash plate should be limited to relatively small value and lateral farce on pistons has an undesirable effect in reciprocating motion. To solve these problems, piston rod mechanism, which is commonly used in bent axis type motor/pump, is considered to be applied to the swash plate type motor/pump. In this paper, kinematic analysis was done on the piston rod mechanism. A series of formula were derived and numerical calculations were done for a set of motor parameters.

• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.343-348
• /
• 2008

In this paper, a CFD (Computational fluid dynamics) code, FLUENT is adopted to investigate accurate flow characteristics for a slipper bearing which is used swash plate type hydraulic axial piston pump. Static pressure and velocity distributions, and velocity vectors are plotted for different film thickness and slipper rotational velocity. In recess region, there exists a doughnut shaped vortex ring. The static pressure distributions are non-uniform and the flow fields are highly asymmetrical under bearing rotation. Therefore the numerical method adopted in this paper can be use in design of hydrostatic components and further studies are required.

• 한국수자원학회논문집
• /
• 제56권10호
• /
• pp.603-617
• /
• 2023

본 연구는 포말대 흐름의 난류특성에 대한 이해를 목표로 한다. 포말대 흐름을 재현하기 위해 이중 댐-붕괴 파랑생성법이 제시되었다. 기존 단일 댐-붕괴 실험과 비교하여 이중 댐-붕괴 실험은 두 개의 수문의 개방 시간을 조절하여 처오름과 처내림의 다양한 상호작용을 구현할 수 있다. 수치모형으로는 OpenFOAM의 overInterDyMFoam이 활용되었다. overInterDyMFoam은 밀도가 다른 두 유체(i.e., 공기, 물)의 경계면 추적기법과 동격자 및 중첩 격자 기법을 결합한 모형이다. 질량보존 및 운동량 방정식으로는 𝜅-𝜖 난류모형이 결합된 이차원 Reynolds-Averaged Navier-Stokes 모형이 채택되었다. 수치모형실험 결과는 수리모형실험의 수심 및 흐름 방향 유속 시계열과 비교하여 정확도가 검증되었다. 난류 운동 에너지 분포특성을 확인하여 각 흐름 단계(i.e., 처오름, 처내림, 흐름의 상호작용)의 난류 진화 특성을 고찰하였다.

• 한국생산제조학회지
• /
• 제24권2호
• /
• pp.244-250
• /
• 2015

We propose a simulation technique to estimate the reduction effect of the pressure/flow pulsation by analysis of the pulsation variables and notch shape of the valve plate of a swash-plate-type variable piston pump. First, using SimulationX$^{(R)}$, we perform a theoretical kinematic analysis according to the variable swash-plate angle and rotational velocity in order to design a single-piston pump. In designing the notch shape of the valve plate of the swash-plate-type variable piston pump as one of the pulsation variables, we investigate the effect of the pulsation by comparing two notch types (circular type and V type). Then, we extend our analysis to a nine-piston pump model. This paper not only confirms the effect of the pressure/flow pulsation according to pulsation variables but can also be applied to the development of a SimulationX$^{(R)}$-based simulation technique for notch-shape optimization for a swash-plate-type variable piston pump.

• 동력기계공학회지
• /
• 제15권5호
• /
• pp.5-9
• /
• 2011

The hydraulic piston using a hydrostatic bearing has been used widely due to its satisfying performance at very high pressurized circumstance and relative higher power density in comparison to conventional one. For high pressurization, enhanced efficiency and long durability of the hydraulic piston, the design of hydrostatic bearing is at issue, which is installed between piston shoe and swash plate. The performance of the hydrostatic bearing is influenced significantly by the assembly of the piston shoe consisting of circular land and recess. In this study, to estimate the performance of the hydrostatic bearing, the characteristics for lubrication of the assembly of the piston shoe were investigated by measuring a leakage rate of hydraulic fluid under an experimental condition, where a rotating velocity of the piston, hydraulic pressure and temperature of the hydraulic fluid were changed systematically. In addition, a film thickness of the hydraulic fluid on the piston shoe was measured and compared to theoretical one.

• 대한기계학회논문집
• /
• 제19권4호
• /
• pp.1062-1070
• /
• 1995

The study deals with controlling the velocity of hydraulic motor with PI controller through the control of displacement pump which has higher efficiency than valve-controlled system. This was done as follows. First, we modified original displacement pump and designed this electrohydraulic puma system. Second, after experimenting static and dynamic characteristics, we identified system parameter of approximated model. Lastly, to control the velocity of hydraulic motor we controlled the angle of the swash plate of displacement pump. Test carried out in the laboratory shows that transient and steady state response could be improved by PI controller reducing power loss.

• 한국유체기계학회 논문집
• /
• 제9권2호
• /
• pp.13-18
• /
• 2006

This paper was studied to design Process considered flexibility and reliability of suction and discharge valves. Flexibility and reliability of valves are main important factors in compressor valves design. And they are incompatible with efficiency of compressor. In this study, we have performed the optimal design of CO2 compressor valves to consider these factors. At first, we analyzed performance simulation of compressor to obtain optimal flexibility level of valves. From this simulation, we could get some important data at valve design like the optimal natural frequency and the height of retainer. After that we studied to reliability of valves corresponding to optimal flexibility level by finite element method. For each case bending stress and natural frequency were obtained by it. Also we investigated the fatigue stability to obtain optimal valve shape that ensured to reliability.

• 설비공학논문집
• /
• 제14권4호
• /
• pp.293-303
• /
• 2002

For successful design of component, performances of one-tank plate type evaporator, gas-liquid separation type condenser, swash plate type compressor and thermostatic expansion valve for automotive air conditioner are investigated experimentally. Heat transfer characteristics in the evaporator are examined by means of air temperature, relative humidity, air volume flow, outlet refrigerant pressure and superheat, and heat transfer characteristics in the condenser are examined by means of air temperature, air velocity and inlet refrigerant pressure. Pressure drops for both evaporator and condenser are measured arid empirical correlations are derived. Volumetric efficiencies and isentropic efficiencies for trio types of compressors with different capacity are measured and compared. Thermostatic expansion valve is tested to investigate the pressure variation according to temperature changes.

• 한국해양공학회지
• /
• 제22권5호
• /
• pp.44-51
• /
• 2008

The planning and design of coastal structures against wave attack is required to accurately predict wave transformation, wave run-up, and fluid. particlevelocities an a slope. On tire other hand, in tire swash and surf zones of a natural beach, where coastal erosion and accretion occur at tire land-sea boundary, hydrodynamic analysis is essential. In this study, a RBREAK2 numerical model was created based on the nonlinear shallow water equation and laboratory measurements were carried out in terms of tire free surface elevations and velocities for tire cases of regular and irregular waves on 1 : 10 and 1 : 5 impermeable slopes. The data were used to evaluate tire applicability and limitations of tire RBREAK2 numerical model. The numerical mode1 could predict tire cross-shore variation of the wave profile reasonably well, but showed more accurate results for slopes that were steeper than 1 : 10. Except near tire wave crest, tire computed depth averaged velocities could represent tire measured profile below tire trough level fairly well.