• Restorative Dentistry and Endodontics
• /
• 제20권2호
• /
• pp.832-838
• /
• 1995

The purpose of this study was to evaluate the amount of marginal microleakage of 2 light curable GI cements(Fuji II LC & VariGlass), which contain some resin components. 4 volunteers kept on acrylic resin plates, which contained dentin disks with cavities filled with test materials for 2 weeks. The time when polishing was done(5 minutes and 24 hours after filling) and the use of protective agents were varied, so 8 groups with each 6 specimens were tested. After having specimens(disks with cavities filled with materials) penetrated with 1% Methylene Blue solution, specimens were stored in 40% nitric acid solution for 4 days to extract adsorbed dye material. Supernatants of centrifuged samples were diluted 5 times and Spectrophotometer was used to determine the degree of absorption. Dye concentration was calculated through the pre-obtained Linear Regression Curve. The results were as follows. 1. The best result was seen in groups (PF24, PV24) which were protected and polished 24 hours later and the opposite phenomenon was seen in groups(NF24, NV24) which were held without protection and polished 24 hours later. Groups polished S minutes later showed moderate leakage pattern. 2. Groups polished 5 minutes later showed similar leakage amount irrespective of using of protective agent. But statistically insignificant lower values were seen in VariGlass than in Fuji II LC groups, So It was considered that VariGlass may be more resistant to early moisture attack than Fuji II LC. 3. In groups polished 24 hours later, there was no significant difference between materials but was definitely significant difference according to the use of protective agent. If the cement in which polishing will be done 24 hours later, Protective agent should be used to cover the surface.

• 융합정보논문지
• /
• 제9권10호
• /
• pp.87-93
• /
• 2019

치유 물질인 아마인유에 형광 물질을 소량 혼합한 혼합물을 코어 성분으로 하여 마이크로캡슐을 제조하였다. 이 마이크로캡슐을 코팅재 조성물에 균일하게 분산시켜 모르타르 표면에 도포함으로써 지기치유 보호코팅재를 제작하였다. 이 코팅재에 약 $100{\mu}m$ 폭의 스크래치 또는 균열 손상을 발생시킨 후 자외선을 조사하면서 관찰한 결과, 캡슐 함량이 증가할수록 형광 발광의 범위가 증가하였고, 20wt% 이상의 캡슐을 함유한 코팅재에서는 손상 부위가 치유물질로 거의 채워진 모습을 나타내었다. 물흡수도 시험 결과 20wt% 이상의 캡슐을 함유한 코팅재는 약 85%의 치유효율을 보였다. 손상 부위에서 나타나는 형광은 3m의 거리에서도 용이하게 식별되었다. 본 연구결과는 콘크리트 보호를 위한 마이크로캡슐형 자기치유 코팅재의 치유기능을 육안으로 용이하게 확인하는데 도움을 줄 것으로 기대된다.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.354-354
• /
• 2006

Alginic acid-silica hydrogel films was prepared for testing as protective coating materials for PTFE OD membranes. Unprotected hydrophobic membranes are subject to wet-out when contacted by surface-active agents. Films were characterised using SEM, XRD, DSC, mechanical strength measurements, and water-swelling measurements. In OD trials using coated membranes, no wet-out occurred over the 15 h duration of three consecutive 5 h OD trials using orange oil-water mixtures. In the case of detergent solutions, the coating afforded protection to the membrane for 4-5 h. In a separate trial, no wet-out occurred when the coated side of the membrane was placed in contact with 1.2 wt % orange oil for 72 hours.

• 한국세라믹학회지
• /
• 제45권10호
• /
• pp.600-604
• /
• 2008

Although titanium-ceramic systems have gained substantial interests in dental prosthetic field, bonding problem between porcelain and titanium has not been solved. Main obstacle in titanium-porcelain bonding is excessive oxidation of titanium during porcelain firing. The effects of several coating materials on the bonding strength of titanium-porcelain system were investigated in this study. RF sputtering and electroplating of platinum significantly increased the bonding strength of porcelain-titanium specimen. However, coatings of Ni-Au, Ir, and ceramics(zirconia and hydroxyapatite) did not showed a significant effect on bonding strength. Platinum might be a promising material for the protective layer of excessive oxidation of titanium during porcelain firing, resulting in increase in the bonding strength.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.525-526
• /
• 2007

Over-polishing is required to completely remove the material of top surface across whole wafer, in spite of a local dishing problem. This paper introduces the two-step CMP process using protective layer and high selectivity slurry, to reduce dishing amount and variation. The 30nm thick protective oxide layer was deposited on the pattern, and then polished with low selectivity slurry to partially remove the projected area while suppressing the removal rate of the recessed area. After the first step CMP process, high selectivity slurry was used to minimize the dishing amount and variation in pattern structure. Experimental result shows that two-step CMP process can be successfully applicable to reduce the dishing defect generated in over-polishing.

• 한국군사과학기술학회지
• /
• 제11권2호
• /
• pp.101-108
• /
• 2008

This study attempted to develop the technology by gaseous ozone for decontaminating building affected by a model of biological weapon agent(Bacillus subtilis spores) instead of Bacillus anthracis spore. The use of ozone is attractive method from a practical point of view of decontamination procedure since it has strong oxidation power but no residue after application. We examined the disinfection efficiency of gaseous ozone to Bacillus subtilis spores which suspension was sprayed on different material surfaces and dried. Three different types of gaseous ozone was applied : dry ozone, dry ozone with humidified air, and water bubbled wet ozone. Dry ozone(1500ppm) failed to achieve any significant inactivation for 2hrs. However, six log reduction of B. subtilis spore was achieved within 30min by 1500ppm of water bubbled wet ozone. This result shows the noticeable inactivation efficiency by gaseous ozone compared with previous studies. Good performance by wet ozone was also found for military material surface.(i.e. : gas mask hood, protective garments, army peinted metal surface).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.142-145
• /
• 2000

The performance of ac plasma display panels (PDP) is influenced strongly by the surface glow discharge characteristics on the MgO thin films. This paper deals with the surface glow discharge characteristics and some physical properties of MgO thin films prepared by reactive RF planar unbalanced magnetron sputtering in connection with ac PDP. The samples prepared with the dc bias voltage of -10V showed lower discharge voltage and lower erosion rate by ion bombardment than those samples prepared by conventional magnetron sputtering or E-beam evaporation. The main factor that improves the discharge characteristics by bias voltage is considered to be due to the morphology changes or crystal structure of the MgO thin film by ion bombardment during deposition process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.338-339
• /
• 2005

The wider surface of the aluminum foil, electrochemically very important and it is necessary to increase the surface area. A study has been made of the fabrication condition for etching cube texture of high purity aluminium foil and of electrochemical etching of the aluminium foil. In the present work, it is shown there exists a relation between the influence of the pre-treatment time in the NaOH & HCI solution and $H_2SO_4$ concentration in the conversion solution. Also effect of temperature during AC etching was also studied. Result of the etched aluminum film is shown in the typical SEM images. Its electrochemical characteristics were investigated by cyclic voltammetry. And effects of current density and frequency is also reported. Cyclic voltammogram showed that the protective oxide film was formedon the inner surfaces of etch pit. the frequency influence resistance of oxide film in AC etching.

• 보존과학회지
• /
• 제35권5호
• /
• pp.385-391
• /
• 2019

인도네시아 보로부두르 보존처리소에서 촬영한 보로부두르 사원 흑백 사진의 재질 특성을 조사하기 위해 과학적 분석을 수행하였다. 흑백 사진에서 시료를 채취하여 현미경 조사, 성분 및 재질 분석을 진행한 결과 흑백 사진은 지지체, 바리타층, 바인더층, 표면층 등 4개의 층으로 구성되어 있는 것을 확인하였다. 지지체는 마섬유로 구성된 종이, 바리타층은 분말상태의 황산바륨(BaSO₄), 바인더층은 할로겐화은이 함유된 유제, 표면보호층은 젤라틴을 사용하여 제작된 것으로 판단하였다. 사진은 구성 재질에 따라 특성 및 보존 환경이 다르므로 시대에 따른 다양한 흑백 사진 재질 특성에 대한 연구가 필요하다.

• 한국기계가공학회지
• /
• 제15권6호
• /
• pp.9-15
• /
• 2016

Due to material-specific vulnerabilities, the surfaces of the liquid crystal glasses used in mobile phones can crack easily, with even the smallest cracks undergoing propagation. To protect the glass surfaces, films are attached to the surfaces during the mobile phone production process. However, after machining the liquid crystal, removal of the film on the liquid crystal surface using chemical and mechanical methods is required. In this research, a peeling apparatus was developed for removing the films attached to liquid crystal surfaces during the production process. Mechanical attachment and design automation through experimentation and finite element modelling were performed to confirm the validity of the design.