• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.510-514
• /
• 2002

The 3-dimensional measuring machine by using an ultrasonic sensor is used one of the NDE(Non Destructive Examination). It is applied to the inspection of pipelines, boreholes, pressure vessel and tank, and so on. In particular when a harsh environment prohibits the use of moving mechanical parts. The 3-dimensional measuring machine by using an ultrasonic sensor, which measure 1-dimensional information and 2-dimensional information simultaneously from a target of inspection, and then reembody 3-dimensional information. So we can find the situation in progress and predict remaining life and corrosion without destructive examination. It's a point of excellence that the 3-dimensional measuring machine is portable.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1350-1353
• /
• 2007

An experimental method based on contact resonance is developed to extract the contact parameters of mechanical joints under various clamped conditions. Mechanical joint parameters of shear contact stiffness and damping were extracted for different physical joint parameters such as surface finish of the mating surfaces, the presence of lubrication, the effect of the clamping pressure, and shear load. It was found that the shear contact stiffness values decreased with increasing clamping load and increased with increasing shear loading. Contact damping ratio values were almost constant with clamping load, but decreased with increasing shear load. Moreover, rough surfaces exhibited the highest shear stiffness and contact damping compared to smooth surfaces.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.43-47
• /
• 1999

Instead of using KrF excimer lasers( ${\lambda}$ = 248 nm) in depositing oxide thin films, as in the most of the laboratories in Korea, we have used an ArF excimer laser( ${\lambda}$ = 197 nm) which has a shorter wavelength. By using a beam which has a shorter wavelength, we could obtain higher quality and smoother surface YBCO thin films. We fabricated YBCO thin films with the various substrate temperature conditions and analyzed the characteristics of these films. We also studied the charateristics of the films fabricated under the various conditions of the power of laser and the oxygen pressure. The characterization tools used in this work were a transport measurement setup, an XRD , and a SEM. We also fabricated STO/YBCO multilayers to use in SFQ devices fabrication. XRD patterns of the multilayers showed that the multilayer films were grown epitaxially.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.1
• /
• pp.67-76
• /
• 2005

In this paper, An analysis on the intelligence system for a biped walking robot(BWR) was made and its results were applied to the BWR. Various sensors were applied to the developed BWR for autonomous and intelligent walk in unknown environments. To measure the distance between the object and BWR, ultrasonic sensor and infrared-rays sensor were used. To identity surrounding environments, vision system was used. Gyro sensor was used to control the posture of BWR. Also, piezoelectricity sensor was used to identity the pressure of foot landing on the surface. Sensors applied to the robot have measurement errors according to noises or walking environments. To improve the function of these sensors, influences of noise or sensing errors were minimized using a sensor fusion scheme. A gait test using the sensor fusion system was performed, and its results are presented.

• Journal of the Korean Ceramic Society
• /
• v.31 no.11
• /
• pp.1323-1329
• /
• 1994

Tape casting and lamination were used to produce heterogeneous laminates with alternating layers of different porosity and homogeneous laminates with component layers of the same porosity. The pore structure was investigated for heterogeneous laminates, and bend strength was measured for comparison with that of homogeneous laminates. For a reference, strength measurement was made for the porous body fabricated by sintering samples dry-pressed at low pressure with spray-dried granules. Strength increase, in the range 50~120 MPa, was achieved in the presence of the surface dense layer, while extensive delamination, presumably responsible for enhanced fracture toughness, took place through the internal porous layer.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.678-683
• /
• 2003

Ultrasonic method using SH(shear horizontal) wave has been developed to determine the surface damage in fatigued material. Fatigue damages based on propagation energy were analyzed by multiregression analysis and phase measurement in interrupted fatigue test specimen including CrMoV and 12Cr alloy steel. From the test results, as the fatigue damage increased the propagation time of the launched waves increased and amplitude of wavelet decreased. Also, analysis for the waveform modulation showed a reliable estimation, with confidence limit of 97% for 12Cr steel and 95% for CrMoV steel, respectively. Therefore, It is thought that SH ultrasonic wave technique can be applied to determine fatigue damage of in-service component nondestructively.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.269-270
• /
• 2006

A finite difference lattice Boltzmann model which allows us to simulate gas-liquid two-phase flows with large density difference, for instance, 800 times for air and water is considered. Two-particle model is used and the density difference is introduced by changing the acceleration according to the fluid density. Numerical measurement of surface tension agrees well with theoretical predictions. Simulations of two-phase phenomenon for phase-transition is carried out, showing applicability of the model for two-phase flows. The two-dimensional cavitating flow around a board set up in the fluid way is also simulated. As a result, it was confirmed that the FDLB method with two-particle model was effective in numerical simulation of cavitating flow and the bubble periodically grew up at the low pressure area behind the board, in which the fluid condition was influenced by the cavitation number.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.187-192
• /
• 2003

The heat (mass) transfer characteristics in the tip-leakage flow region of a high-turning first-stage turbine rotor blade has been investigated by employing the naphthalene sublimation technique. The heat transfer data in the tip-leakage flow area for the tip clearance-to-span ratio, h/s, of 2.0% are compared with those in endwall three-dimensional flow region without tip clearance (h/s = 0.0 %). The result shows that the thermal load in the tip-leakage flow region for h/s = 2.0% is more severe than that in the endwall flow region for h/s = 0.0%. The thermal loads even at the leading and trailing edges for h/s = 2.0% are found larger than those for h/s = 0.0%. The tip-leakage flow results in heat transfer augmentations near the tip on both pressure and suction sides in comparison with the mid-span results.

• Proceedings of the KWS Conference
• /
• 2003.05a
• /
• pp.155-158
• /
• 2003

Orbital GTA welding is used in the pressure pipe line of auto-mobile, LNG and plant piping. To weld the pipe line safely, to some extent, the back bead must be formed in the root pass. In the plate welding the back bead can be observed, but in the pipe welding, the back bead can not be observed directly. In the welding around circumference, the parameters such as gravity, surface tension and arc force are different at each position. And then D/B for welding condition at each position are required. We also studied about the setting of the optimum orbital welding condition by controlling heat input.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.393-396
• /
• 1996

The electrical characteristics of stearic acid LB films far the horizontal direction were investigated to develop the gab sensor using LB films. $\pi$ -A isotherm was measured to transfer stearic acid on slide glass substrate and surface pressure for optimal deposition was 25[dyne/cm]. The deposition status of stearic acid LB films was verified by the measurement of capacitance which was increased with the number of layers. The thickness of electrode was estimated about 1000 by the I-V characteristics far the horizontal direction. The Conductivity of stearic acid LB films for horizontal direction was 10$^{-8}$ [S/cm] that mean like semiconductor.