• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.3
• /
• pp.273-278
• /
• 2012

The use of Al alloys instead of fiber-reinforced plastic(FRP) in ship construction has increased because of the advantages of Al-alloy ships, including high speed, increased load capacity, and ease of recycling. This paper describes the effects of probe diameter on the optimum friction stir welding conditions of 5456-H116 alloy for leisure ship, measured by a tensile test. In friction stir welding using a probe diameter of 5 mm under various travel and rotation speed conditions, the best performance was achieved with a travel speed of 61 mm/min. Using a probe diameter of 6 mm, rotation speeds of 170-210 rpm, and a travel speed of 15 mm/min produced a rough surface and voids because of insufficient heat input produced by the low rotation speed. At 500-800 rpm, chips were observed, although there were no voids, and the weld surface was excellent. However, at 1100-2500 rpm, many chips were produced due to excessive heat input. Heat effects were very evident on the bottom. For a travel speed of 15 mm/min, heat input caused by friction increased as the rotation speed increased. The mechanical characteristics were degraded by accelerated softening due to increasing heat input.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.10a
• /
• pp.26-31
• /
• 1998

The effect of tool angles on the surface roughness in face milling is studied. First, the relation between tool angles and rotation angles is identified. Using this relationship, it is obtained that the projection of insert nose shape on cutting profile, which is a part of ellipse. The effect of spindle tilt is also considered for the tool angles. It si shown that tool angles along with nose radius and feed rate have an effect on surface roughness.

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.1
• /
• pp.51-56
• /
• 2009

The detailed heat transfer coefficient on a rotating dimpled channel were measured using the transient liquid crystal technique. The channel height to dimple diameter was 2, dimple center distance to dimple diameter was 1.5 and channel aspect ratio was 4. Tested Reynolds number based on the channel hydraulic diameter was varied from 15000 to 35000 and corresponding rotation number was ranged from 0.026 to 0.057. Results showed that the Coriolis force by rotation enhanced the heat transfer coefficient on the trailing surface. As the Reynolds number increased, i.e. rotation number decreased, the heat transfer coefficient increased and the thermal performance factor decreased.

• Honam Mathematical Journal
• /
• v.38 no.2
• /
• pp.305-316
• /
• 2016

In this paper we study general rotational surfaces in the 4-dimensional Euclidean space $\mathbb{E}^4$ and give a characterization of flat general rotational surface with pointwise 1-type Gauss map. Also, we show that a flat general rotational surface with pointwise 1-type Gauss map is a Lie group if and only if it is a Clifford torus.

• PNF and Movement
• /
• v.12 no.4
• /
• pp.243-248
• /
• 2014

Purpose: The transverse abdominis and themultifidus muscle are located in the core. They surround one's trunk and help in body stabilization. Specifically, they control spine articulation to maintain posture and balance. Therefore, weakened deep muscle in the trunk may cause spinal malalignment. This study aims to compare the correlation between the thickness of the transverse abdominis and the multifidus muscle and the spine alignment among college students in their 20s. Methods: This study measured the thickness of the transverse abdominis and the multifidus muscle of 42 healthy college students in their 20s using ultrasonic waves. The thickness of the muscle was measured for the length of the cross-section except for fascia. The thickness of the left and right muscles was measured, and the mean value was calculated. As the thickness of the transverse abdominis can increase because of pressure during exhalation, it was measured at the last moment of exhalation. Spinal alignment was measured by the kyphosis angle, lordosis angle, pelvic tilt, trunk inclination, lateral deviation, trunk imbalance, and surface rotation using Formetric III, which is a three-dimensional imaging equipment. They were measured for three times, and the mean values were calculated. The general characteristics of the subjects were analyzed using descriptive statistics. The correlations between each factor were analyzed using Pearson's correlation analysis. Results: The transverse abdominis showed asignificant correlation with trunk inclination (p<.05). The multifidus muscle showed a significant positive correlation with pelvic tilt and a negative correlation with surface rotation (p<.05). Conclusion: The thickness of transverse abdominis and the multifidus muscle appears to influence spinal alignment. Specifically, the multifidus muscle, which plays an important role on the sagittal plane, influences surface rotation, thus making it an important muscle for scoliosis patients. Therefore, a strengthening training program for the transverse abdominis and the multifidus muscle is necessary according to specific purposes among adults with spinal malalignment.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.5 s.236
• /
• pp.590-598
• /
• 2005

The present study has been conducted to investigate the effect of discrete ribs and rotation on heat/mass transfer characteristics in a two-pass square duct with $90^{\circ}-rib$ turbulators. The rib turbulator has a square cross section of 1.5 mm. The rib height-to-hydraulic diameter ratio $({e/D_{h})$ is 0.056, and the rib pitch-to-rib height ratio (p/e) is 10. The gap width is the same as the rib height. The rotation number ranges from 0.0 to 0.2 while Reynolds number is fixed to 10,000. In a stationary duct, the heat/mass transfer on the surfaces with discrete ribs is enhanced because the gap flow promotes local turbulence and flow mixing near the ribbed surface. In a rotating duct, the gap flow affects differently the heat/mass transfer on leading and trailing surfaces with discrete ribs. On the leading surface of the first pass, heat/mass transfer is increased due to the gap flow. On the trailing surface of the first pass, however, heat/mass transfer is decreased because the gap flow disturbs reattachment of main flow. The phenomenon, that is, the difference of heat transfer between the leading and the trailing surfaces is distinctly presented by rotation.

• Physical Therapy Korea
• /
• v.21 no.3
• /
• pp.1-10
• /
• 2014

The aim of this study was to investigate the effect of hip external rotation angle on pelvis and lower limb muscle activity during prone hip extension. Sixteen healthy men were recruited for this study. Each subject performed an abdominal drawing-in maneuver (ADIM) in a prone position, and extended the dominant hip at three different hip external rotation angles ($0^{\circ}$, $20^{\circ}$, $40^{\circ}$) with a $30^{\circ}$ hip joint abduction. Activity of the gluteus maximus (G Max), gluteus medius (G Med), and hamstring (HAM) and the G Max/HAM and G Med/HAM ratios were determined with surface electromyography (EMG). The EMG signal was normalized to 100% maximum voluntary isometric contractions (MVICs) and expressed as %MVIC. Data were analyzed by one-way repeated analysis of variance (alpha level=.05) and the Bonferroni post hoc test. Significant differences in G Max and G Med muscle activity were noted among the three different hip external rotation angles. G Max muscle activity increased significantly at both $40^{\circ}$ (p=.006) and $20^{\circ}$ (p=.010) compared to a $0^{\circ}$ hip external rotation angle. G Med muscle activity increased significantly at $20^{\circ}$ (p=.013) compared to a $40^{\circ}$ hip external rotation angle. The G Max/HAM activity ratio increased significantly at both $40^{\circ}$ (p=.004) and $20^{\circ}$ (p=.014) compared to a $0^{\circ}$ hip external rotation angle. The G Med/HAM activity ratio increased significantly at $20^{\circ}$ (p=.013) compared to a $40^{\circ}$ hip external rotation angle. In conclusion, $40^{\circ}$ and $20^{\circ}$ hip external rotation angles are recommended to increase G Max activity, and $20^{\circ}$ hip external rotation is advocated to enhance G Med muscle activity during prone hip extension with ADIM and $30^{\circ}$ hip abduction in healthy subjects.

• The Bulletin of The Korean Astronomical Society
• /
• v.45 no.1
• /
• pp.60.3-61
• /
• 2020

We perform disk-halo decomposition of the Large Magellanic Cloud (LMC) using a novel HI velocity field extraction method, aimed at better deriving its HI kinematics and thus the dark matter density profile. For this, we use two newly developed galaxy kinematic analysis tools, BAYGAUD and 2DBAT which have been used for the kinematic analysis of resolved galaxies from Australian Square Kilometre Array (ASKAP) observations like WALLABY which is an all-sky HI galaxy survey in southern sky. By applying BAYGAUD to the combined HI data cube of the LMC taken with the Australia Telescope Compact Array (ATCA) and Parkes radio telescopes, we decompose all the line-of-sight velocity profiles into an optimal number of Gaussian components based on Bayesian MCMC techniques. From this, we disentangle turbulent non-circular gas motions from the overall rotation of the galaxy. We then derive the rotation curve of the LMC by applying 2DBAT to the separated circular motions. The rotation curve reflecting the total kinematics of the LMC, dark and baryonic matters is then be combined with the mass models of baryons, mainly stellar and gaseous components in order to examine the dark matter distribution. Here, we present the analysis of the extracted HI gas maps, rotation curve, and J, H and K-band surface photometry of the LMC.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.6
• /
• pp.447-456
• /
• 2014

In this paper, a new damage-detection method based on structural vibration is proposed. The essence of the proposed method is the detection of abrupt changes in rotation. Damage-induced rotation (DIR), which is determined from the modal flexibility of the structure, initially occurs only at a specific damaged location. Therefore, damage can be localized by evaluating abrupt changes in rotation. We conducted numerical simulations of two damage scenarios using a 10-story cantilever-type building model. Measurement noise was also considered in the simulation. We compared the sensitivity of the proposed method to localize damage to that of two conventional modal-flexibility-based damage-detection methods, i.e., uniform load surface (ULS) and ULS curvature. The proposed method was able to localize damage in both damage scenarios for cantilever structures, but the conventional methods could not.

• Journal of the Korean Academy of Clinical Electrophysiology
• /
• v.10 no.2
• /
• pp.23-29
• /
• 2012

Purpose : Purpose of this study was to investigate whether cervicothoracic posture was associated with scapula orientation and muscle activity during shoulder abduction. Methods : Cervicothoracic junction angle and thoracic kyphosis angle were measured in health twenty subjects. Then, scapular resting orientation and range of motion (upward/downward rotation, internal/external rotation) and muscle activity (upper trapezius, lower trapezius, serratus anterior) was determined using motion capture system and surface electromyography while subjects performed shoulder abduction. Results : Cervicothoracic junction angle was significantly associated with range of motion of scapular internal/external rotation during shoulder abduction. Thoracic kyphosis angle was significantly associated with scapular resting orientation of upward/downward rotation and average IEMG of lower trapezius. Conclusion : The result of this study shows that poor cervicothoracic posture is relationship with altered scapular kinematics cause of shoulder dysfunction. These findings suggested that cervicothoracic posture may be considered in occupation and exercise including arm elevation over head as well as used as predict factor to estimate shoulder dysfunction.