• 센서학회지
• /
• 제2권1호
• /
• pp.65-74
• /
• 1993

본(本) 연구(硏究)에서는 소형(小型) 정전유도형(靜電誘導型) 모터를 제작하고 이 모터에 인가하는 3상(相) 교류전압(交流電壓) 및 주파수(周波數)를 가변(可變)하였을 때의 회전자(回轉字)의 회전속도(回轉速度)의 특성을 실험적으로 검토하였다. 또한 정전유도형(靜電誘導型) 모터의 작동기구상(作動機構上) 회전자(回轉字) 표층물질(表層物質) 및 내층물질(內層物質)의 표면저항율(表面抵抗率), 비유전율(比誘電率) 및 전하완화시정수(電荷緩和時定數)를 변화시켜 회전자(回轉字) 및 고정자(固定子) 사이의 전계강도(電界强度) 및 회전자(回轉字) 표면물질상(表面物質上)의 표면유기전하(表面誘起電荷)의 분포(分布) 및 유기속도(誘起速度)를 변화시킴으로서 소형(小型) 정전유도형(靜電誘導型) 모터의 회전자의 회전속도에 미치는 영향을 검토하였다. 실험(實驗) 결과(結果), 회전자(回轉字) 표층물질(表層物質)의 비유전율(比誘電率), 표면저항률(表面抵抗率) 및 전하완화시정수(電荷緩和時定數) 및 내층물질(內層物質)의 비저항율(比抵抗率)이 모터의 회전속도(回轉速度)에 매우 큰 영향을 미침이 확인되었다. 또한 모터에 인가하는 3상(相) 전원(電源)의 전압(電壓) 및 주파수(周波數)도 모터의 회전(回轉)에 매우 큰 영향을 주며, 회전속도(回轉速度)는 인가전압(印加電壓) 및 주파수(周波數)에 일차(一次) 비례(比例)하여 증가함을 보여주었다. 회전자의 표층물질(表層物質)이 $BaTiO_{3}$ 80% 내층물질(內層物質)이 Cu 일때 무부하(無負荷) 최대속도(最大速度)는 4.5 kV, 220 Hz에서 5500 rpm이 얻어졌다.

• 소성∙가공
• /
• 제16권7호
• /
• pp.521-529
• /
• 2007

This paper is concerned with the analysis on the surface expansion of AA 2024 and AA 1100 aluminum alloys in backward extrusion process. Due to heavy surface expansion appeared usually in the backward can extrusion process, the tribological conditions along the interface between the material and the punch land are very severe. In the present study, the surface expansion is analyzed especially under various process conditions. The main goal of this study is to investigate the influence of degree of reduction in height, geometries of punch nose, friction and hardening characteristics of different aluminum alloys on the material flow and thus on the surface expansion on the working material. Two different materials are selected for investigation as model materials and they are AA 2024 and AA 1100 aluminum alloys. The geometrical parameters employed in analysis include punch corner radius and punch nose angle. The geometry of punch follows basically the recommendation of ICFG and some variations of punch geometry are adopted to obtain quantitative information on the effect of geometrical parameters on material flow. Extensive simulation has been conducted by applying the rigid-plastic finite element method to the backward can extrusion process under different geometrical, material, and interface conditions. The simulation results are summarized in terms of surface expansion at different reduction in height, deformation patterns including pressure distributions along the interface between workpiece and punch, comparison of surface expansion between two model materials, geometrical and interfacial parametric effects on surface expansion, and load-stroke relationships.

• 조명전기설비학회논문지
• /
• 제21권8호
• /
• pp.129-135
• /
• 2007

환경오염이 심한 분진 발생지역에서는 전기 사고가 자주 발생하기 때문에 전기설비에 대한 유지관리와 예방에 대한 연구가 필요하다. 특히 외부에 전기절연물이 장기간 노출되면, 쉽게 분진이 축적되고 수분, 습기 등에 의한 누설전류의 발생으로 전기사고에 이르게 된다. 따라서 본 연구에서는 분진, 염수 등에 의한 전기설비 절연재료 표면변화와 표면 누설전류를 측정하였다. 측정결과로부터 베이클라이트의 표면이 다른 재료보다 염수에 대한 영향이 심하였다. 또한 베이클라이트 표면 누설전류는 반복되는 염수 오염에 의해 증가하고 재료표면은 미소아크가 발생하고 탄화되었다. 따라서 절연물에서의 누설전류를 억제하기 위해서는 재료의 형태 및 표면 코팅 등이 변화가 필요하다.

• Journal of Korean Vacuum Science & Technology
• /
• 제5권2호
• /
• pp.33-37
• /
• 2001

We measured x-ray magnetic circular dichroism of Co films on Pd(111) surface with and without Pd capping layer at the Co L$_2$,$_3$ edges. Perpendicular magnetization and orbital-moment enhancement are induced by the capping layer. The increase of perpendicular magnetic anisotropy induced by capping layer is considered to result from the increase of surface anisotropy due to the hybridization at the surface.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.509-512
• /
• 1999

The main problem in porcelain as a high voltage insulator is that the water film is felled on the insulator surface due to rain, flog, and dew. In the presence of contamination. leakage current increases which may lead to flashover that could be followed by an outage of the power system. These days, high voltage polymer outdoer insulators have been studied and widely used, because they have excellent electrical and mechanical properties, superior performance of flashover for contamination. light weight, easy installation or handling. no maintenance during service, competitive price, and so on. First of a1l the excellent performance of the silicone rubber in polluted and wet conditions is attributed to the ability of the material to maintain the hydrophobicity of the surface in the presence of severe contaminants and wet conditions. This is due to a low surface energy of the silicone rubber. But the leakage current and some surface discharge occurs on the surface of insulator when the insulator is used for a long time. So the leakage current and the surface discharge current are important lo estimate the condition of the silicone rubber surface. In this paper, the average leakage current the surface discharge current the surface rubber surface with the salt fog condition for the first stage.

• Current Photovoltaic Research
• /
• 제6권3호
• /
• pp.86-90
• /
• 2018

To generate more current in crystalline silicon solar cells, surface texturing is adopted by reducing the surface reflection. Conventionally, random pyramid texturing by the wet chemical process is used for surface texturing in crystalline silicon solar cell. To achieve higher efficiency of solar cells, well ordered inverted pyramid texturing was introduced. Although its complicated process, superior properties such as lower reflectance and recombination velocity can be achieved by optimizing the process. In this study, we investigated optical and passivation properties of inverted pyramid texture. Lifetime, implied-Voc and reflectance were measured with different width and size of the texture. Also, effects of chemical rounding at the valley of the pyramid were observed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.435-438
• /
• 2002

In this paper, the effect of surface tension, wettability, flow rate of contaminants with varying surfactant content and frequency of applied voltage on the tracking breakdown of epoxy insulating materials were investigated. As the flow rate of contaminant is increased, the surface resistivity is decreased, and the leakage current is increased, the time to tracking breakdown is decreased. It is found that time to tracking breakdown depends on the surface tension of contaminant, that is difference of wettability And as the frequency of applied voltage is increased, time to tracking breakdown decreased.

• 대한기계학회논문집
• /
• 제14권2호
• /
• pp.269-275
• /
• 1990

Nonaxisymmetric bifurcation behaviours of composite tubes two different materials subjected to uniform radial shrinkage at the external surface have been investigated and compared with those of single tube. The effect of material parameters normalized with respect to those of outer tube upon the bifurcation point and corresponding mode has been clarified. The parameters substantially affect the bifurcation mode with long-wavelength so that the composite tube with low hardening exponent or with high yield stress of inner tube destabilizes the overall deformation of the tube. However surface type bifurcation, short-wavelength mode, shown on the traction-free inner surface is hardly affected by the material parameters. The surface type bifurcation completely depends on the material characteristics of inner tube and the bifurcation point of composite tube almost coincides with the of single tube.

• 한국공작기계학회논문집
• /
• 제15권2호
• /
• pp.66-72
• /
• 2006

The old technique of sandblasting which has been used for paint or scale removing, deburring and glass decorating has recently been developed into a powder blasting technique for brittle materials, capable of producing micro structures larger than $100{\mu}m$. In this paper, we studied on the predictive modeling of material removal and surface roughness in powder blasting of glass by design of experiments. The surface characteristics and surface shape of powder blasted glass surface were tested under different blasting parameter. Finally, we proposed a predictive model for powder blasting process, and compared with experimental results.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.202-203
• /
• 2017

In this study, the concept of exposed concrete is basically considered and various expressions of concrete surface texture are verified variously. Based on this comparison, the characteristics of exposed surface of concrete according to the change of coating material applicable to formwork are compared and analyzed. I am trying to find a way to apply exposed concrete in a convenient way, In order to observe the characteristics of concrete exposed surface according to the form material, As the surface is smooth and tight, the surface condition of the concrete is smooth and the pore is small.