• 제목/요약/키워드: surface inversion layer

검색결과 117건 처리시간 0.037초

아파트 단지내의 열섬효과가 대기오염물질 확산에 미치는 영향 해석을 위한 열유동장 수치모의 (A Numerical Simulation of Heat Flow Field for Heat Island Effect Analysis to Air Pollutants Dispersion in Apartment Complex)

  • 장은숙
    • 한국환경과학회지
    • /
    • 제14권6호
    • /
    • pp.577-582
    • /
    • 2005
  • Enormous apartment complexes in urban areas, temporary inversion state and heat island effect occur due to the strong sunshine and weak wind speeds which hinders the dispersion of air pollutants that are emitted from neighboring areas of apartment complexes. In this study, analysis were conducted by using the Fluent code based on the CFD(Computation Fluid Dynamics), including building layout, material, building height from the ground surface, the heat, analysis of flow field in the apartment complex. It was estimated that the temporal radiation inversion phenomenon during the daytime, which was caused by the weak wind speed and higher temperatures in the upper level, contributed to the stagnation of the air pollutants in the lower layer of the apartment complex.

춘계 베링해 알류산 해분의 해양환경 특성 (Characteristics of the Oceanographic Environment in the Aleutian Basin of the Bering Sea during Spring)

  • 최석관;오택윤
    • 한국수산과학회지
    • /
    • 제46권2호
    • /
    • pp.201-215
    • /
    • 2013
  • The characteristics of the oceanographic environment in the Aleutian Basin of the Bering Sea during spring in 1996, 1997, and 1999 were clarified. An investigation of the water properties revealed five basic layers in the Bering Sea during spring: (1) a surface layer of warm and low-salinity water induced by solar heating, (2) a subsurface layer of cold and low-salinity water propagated slowly by heat from the surface layer, (3) a thermocline layer where salinity was constant but temperature sharply decreased, (4) a temperature inversion layer, and (5) a deep layer with a gradual decrease in temperature and increase in salinity toward the bottom. The ranges of water temperature and salinity were $1.8-5.5^{\circ}C$ and 31.81-34.08 in 1996, $1.5-7.2^{\circ}C$ and 31.9-34.06 in 1997, and $0.5-5.6^{\circ}C$ and 32.0-34.11 in 1999, respectively. The water temperature of the surface layer was approximately $1.6^{\circ}C$ higher in 1997 than in 1996 and 1999. The lowest temperature at a depth of 100-150 m was about $1^{\circ}C$ lower in 1999 than in 1996 and 1997. Nutrient levels (nitrate, phosphate, and silicate) contributing to the control of the growth of phytoplankton were higher in the Aleutian Basin than in the eastern continental shelf and Bogoslof Island area. This was closely associated with the phytoplankton distribution. Nutrient concentrations were lowest at a depth of 25 m. The high primary production at that depth was confirmed from the vertical distribution of chlorophyll a. Chlorophyll a levels were above $4.0{\mu}L^{-1}$ in some areas in 1996 and 1999, but below $2.0{\mu}L^{-1}$ in most areas in 1997. Zooplankton density was about three times higher in 1999 than in 1997.

하이브리드 발견적 탐색기법을 이용한 천부 굴절법 자료의 파형역산 (Waveform inversion of shallow seismic refraction data using hybrid heuristic search method)

  • Takekoshi, Mika;Yamanaka, Hiroaki
    • 지구물리와물리탐사
    • /
    • 제12권1호
    • /
    • pp.99-104
    • /
    • 2009
  • 본 연구에서는 천부 토양층의 2차원 불균질 S파 단면을 결정하기 위해 천부 굴절법 탐사로부터 얻은 SH파 자료에 대한 파형역산 기법을 제안한다. 2차원 매질에서 SH파의 전파를 모사하기 위해 2.5차원 파동 방정식을 사용한다. 합성탄성파를 계산하기 위해 공간축으로 4차, 시간축으로 2차 근사한 staggered grid 유한차분법을 사용하여 파동 방정식을 푼다. 계산된 파형과 측정 파형의 잔여오차로 정의되는 목적함수를 하이브리드 발견적 탐색기법에 의해 최소화한다. 2차원 지하구조 모형은 각기 다른 심도 경계면을 갖는 블록과 블록 내부의 S파 속도에 의해 매개화한다. 수치실험은 암영층파 불규칙한 경계를 갖는 모델에 대해 백색잡음을 추가한 합성 SH파 자료를 이용하여 수행하였다. 지표 굴절법 자료로부터 암영층을 포함한 구조를 적절한 계산시간 내에 영상화할 수 있었다

한국 동해의 밀도역전 현상 (INVERSION PHENOMENA OF DENSITY IN THE JAPAN SEA)

  • 김희준;조규대
    • 한국해양학회지
    • /
    • 제17권2호
    • /
    • pp.51-58
    • /
    • 1982
  • 1965년 부터 1979년 까지 한국 동해에서 관측된 온도 및 염분 자료를 이용하여 밀도역전 현상을 조사하였다.그 결과 밀도역전 여름보다 겨울에 많은 것으로 나타났다.겨울에는 동해 전 해역의 절반정도에서 역전층이 형성되며,여름에는 대한해엽의 일부해협에서만 일어난다.또한 역전층의 깊이는 보통 표층에서 수십 m까지이다.이와같은 역전현상은 표층 Ekman수송에 의한 냉수의 이류로 설명 할 수 있다. 즉,겨울에는 북서 계절풍에 의한 표층 냉수의 남하로 인하여 생기며,여름에는 남서퓽에 의해서 연안 근처에서 용승된 저층 냉수가 대한해협 쪽으로 공급되어 일어난다고 생각된다.

  • PDF

沿岸境界層에서의 表層風의 日變化 (Diurnal Variation of the Surface Wind in the Coastal Boundary Layer)

  • 최효
    • 한국해양학회지
    • /
    • 제19권2호
    • /
    • pp.210-216
    • /
    • 1984
  • 5년간의 시간별 풍속 자료를 이용하여 연안 표층풍의 일변화가 분석되었다. 특히 내륙으로 부는 바람 (onshore flow)이 지배적인 계절에는 야간 최대풍의 최대 출현 빈도가 자정에 나타났다. 연평균 남풍 계열을 갖는 야간 최대풍은 북풍 계열 보다 약 3배이상의 출현을 보여준다. 중림의 대기 안정도가 연안에 지배적이므로 바람이 해양에서 내륙으로 불 경우는 (offshore flow) 상승된 전선역전층과 지표역전층에 의해 형성된 전단력(shear flow)이 연안경계층으로 전이되어 야간 연안 최대표층풍이 형성된다.

  • PDF

표면 채널 모스 소자에서 유효 이동도의 열화 (The Degradations of Effective Mobility in Surface Channel MOS Devices)

  • 이용재;배지칠
    • 한국전기전자재료학회:학술대회논문집
    • /
    • 한국전기전자재료학회 1996년도 춘계학술대회 논문집
    • /
    • pp.51-54
    • /
    • 1996
  • This paper reports the studies of the inversion layer mobility in p-channel Si MOSFET's under hot-carrier degradated condition. The validity of relationship of hot carrier degradations between the surface effective mobility and field effect mobility and are examined. The effective mobility(${\mu}$$\_$eff/) is derived from the channel conductances, while the field-effect mobility(${\mu}$$\_$FE/) is obtained from the transconductance. The characteristics of mobility curves can be divided into the 3 parts of curves. It was reported that the mobility degradation is due to phonon scattering, coulombic scattering and surface roughness. We are measured the mobility slope in curves with DC-stress [V$\_$g/=-3.1v]. It was found that the mobility(${\mu}$$\_$eff/ and ${\mu}$$\_$FE/) of p-MOSFET's was increased by increasing stress time and decreasing channel length. Because of the increasing stress time and increasing V$\_$g/ is changed oxide reliability and increased vertical field.

  • PDF

풍암분지 시험시추공 주변에서의 지표 및 시추공 초동주시 동시역산 (Simultaneous traveltime inversion of surface and borehole seismic data in Pungam basin)

  • 김기영;홍명호
    • 지구물리
    • /
    • 제9권1호
    • /
    • pp.37-45
    • /
    • 2006
  • 풍암분지 내에 위치한 140 m 깊이 시험시추공 주변에서 지표 굴절법 및 원거리 수직탄성파 자료의 초동주시를 토모그래피방식으로 동시에 역산하여 시추공 주변의 속도구조를 구하였다 . 지진총으로 발생시킨 지진파는 시추공을 중심으로 N20°E 방향과 이에 수직인 측선을 따라 3 m 간격의 42개 지표 측점과 공내 71 m 깊이에서 수신하였다 . 는 시추공으로부터의 수평거리 -19.5∼+19.5 m인 지표 측점에서 5 kg 해머로 발생시켰으며 , 1∼2 m 간격의 깊이 9∼99 m 구간에서 3성분으로 204 ms 동안 기록하였다 . 지연시간 보정 후 , 이 자료를 지진총으로 기록한 지표 기록자료 초동주시와 동시에 SIRT 방식으로 역산하여 속도 토모그램을 작성하였다 . 속도 토모그램은 평균 1.5 m 두께의 속도 500 m/s 표토층이 속도 3,067∼5,717 m/s의 속도를 갖는 기반암 위에 분포하고 있음을 보여 준다 . 기반암 내부에는 깊이 30∼44 m 구간과 71 m 하부에 속도가 5,130 m/s 이상 되는 매우 단단한 암층이 존재하며 , 이는 코아분석 자료와 비교할 때 사암 및 이암층에 협재하는 역암층의 영향으로 판단된다 . 시추공 주변 조사범위 내에서 대규모 파쇄대나 단층 존재의 증거는 발견되지 않는다 .

  • PDF

쉴드 TBM터널 상부 지반 연약대 전기탐사 (Electrical Resistivity Imaging for Upper Layer of Shield TBM Tunnel Ceiling)

  • 정현기;박철환
    • 한국지반공학회:학술대회논문집
    • /
    • 한국지반공학회 2005년도 춘계 학술발표회 논문집
    • /
    • pp.401-408
    • /
    • 2005
  • Recently shield TBM tunnellings are being applied to subway construction in Korean cities. Generally these kinds of tunnellings have the problems in the stability of ground such as subsidence because urban subway is constructed in the shallow depth. A sinkhole occurred on the road just above the tunnel during tunneling in Kwangju, so a survey for upper layer of the tunnel was needed. But conventional Ground Probing Radar can't be applicable due to the presence of steel-mesh screen in the shield segment, so no existent geophysical method is applicable in this site. Because the outer surface of each shield segment is electrically insulated, dipole-dipole resistivity method which is popular in engineering site investigation, was tried to this survey for the first time. Specially manufactured flexible ring-type electrodes were installed into the grouting holes at an interval of 2.4 m on the ceiling. The K-Ohm II system which has been developed by KIGAM and tested successfully in many sites, was used in this site. The system consists of 1000Volt-1Ampere constant-current transmitter, optically isolated 24 bit sigma-delta A/D conversion receiver - maximum 12 channel simultaneous measurements, and graphical automatic acquisition software for easy data quality check in real time. Borehole camera logging with circular white LED lighting was also done to investigate the state of the layer. Measured resistivity data lack of some stations due to failing opening lids of holes, shows general high-low trend well. The dipole-dipole resistivity inversion results discriminate (1) one approximately 4 meter diameter cavity (grouted but incompletely hardened, so low resistivity - less than $30{\Omega}m$), (2) weak zone (100-200${\Omega}m$), and (3) hard zone (high resistivity - more than 1000${\Omega}m$) very well for the distance of 320 meters. The 2-D inversion neglects slight absolute 3-D effect, but we can get satisfactory and useful information. Acquired resistivity section and video tapes by borehole camera logging will be reserved and reused if some problem occurs in this site in the future.

  • PDF

층상 반무한 지반의 물성치 추정을 위한 마르코프 연쇄 몬테카를로 모사 기법 (Markov Chain Monte Carlo Simulation to Estimate Material Properties of a Layered Half-space)

  • 이진호;;이세혁
    • 한국전산구조공학회논문집
    • /
    • 제36권3호
    • /
    • pp.203-211
    • /
    • 2023
  • 층상 반무한체에서의 확률론적 완전파형역산을 위한 Markov chain Monte Carlo (MCMC) 모사 기법을 정식화한다. Thin-layer method를 사용하여 조화 수직 하중이 작용하는 층상 반무한체의 지표면에서 추정된 동적 응답과 관측 데이터와의 차이 및 모델 변수의 사전 정보와의 차이를 최소화하도록 목적함수와 모델 변수의 사후 확률밀도함수를 정의한다. 목적함수의 기울기에 기반하여 MCMC 표본을 제안하기 위한 분포함수와 이를 수락 또는 거절할지 결정하는 수락함수를 결정한다. 기본 진동모드 뿐만이 아니라 고차 진동모드가 우세한 경우를 포함하여 다양한 층상 반무한체의 전단파 속도 추정에 제안된 MCMC 모사 기법을 적용하고 그 정확성을 검증한다. 제안된 확률론적 완전파형역산을 위한 MCMC 모사 기법은 층상 반무한체의 전단파 속도와 같은 재료 특성의 확률적 특성을 추정하는 데 적합함을 확인할 수 있다.

초음파현미경에서 V(z) 곡선을 이용한 세라믹/금속 접합계면의 비파괴평가 (Nondestructive Evaluation of Ceramic/Metal Interface Using the V(z) Curve of Scanning Acoustic Microscope)

  • 박익근;이철구;조동수;김용권
    • Journal of Welding and Joining
    • /
    • 제23권2호
    • /
    • pp.59-65
    • /
    • 2005
  • A leaky surface acoustic wave (LSAW) velocity was measured using a scanning acoustic microscope on the ceramic/metal interface in order to investigate material properties. The inverse Fourier transform (IFFT) of the V(z) curve contains the reflectance function of a liquid-specimen interface. So, the longitudinal, transverse, and Rayleigh wave velocities for each layer are obtained by the inversion of the V(z) curve at the same time. This paper contains mainly the experimental procedure for measurements of the LSAW velocity, and the results obtained for the velocity variation of individual layer after the thermal shock. It is shown that this method is useful in measuring the material properties under external stress.