• Journal of the Korean Applied Science and Technology
• /
• v.14 no.2
• /
• pp.35-40
• /
• 1997

The organization of phospholipid monolayers and their monolayers mixed with fatty acid containing azobenzene on the water surface was investigated by means of the displacement current measurement method. The phase transition from the gaseous phase to the gaseous-fluid phase which accompanies the polar ordering of phospholipid molecules was detected in the range of immeasurably low surface pressure. The molecular area which gives the onset of the transition was determined for phospholipid monolayers. The Maxwell displacement current(MDC) pulses were generated across mixed monolayers due to the photoisomerization of fatty acid containing azobenzene by alternating irradiation of ultraviolet and visible light, because the condensation of pure azobenzene monolayers was loosened by the introduction of phospholipids into the monolayers. The displacement currents generated during light irradiation were also investgated in connection with monolayer compression cycles. It was found that the maximum of MDC appeared at the molecular area just before the initial rise of surface pressure in compression cycles.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.2
• /
• pp.213-218
• /
• 2011

Displacement current measuring technique has been applied on the study of polyamic acid monolayer containing p-nitroazobenzene. The displacement current was generated from monolayer on the water surface by monolayer compression and expansion. Maxwell displacement current(MDC) was generated when the area per molecule was about $200{\AA}^2$ and $70{\AA}^2$. Maxwell displacement currents were investigated in connection with monolayer compression cycles. It was found that the maximum of MDC appeared at the molecular area just before the initial rise of surface pressure in compression cycles. The monolayer surface morphology of the LB film have been measured by Atomic Force Microscope(AFM). As a result, we confirmed that the microscopic properties of LB film by AFM showed the good orientation of monolayer molecules and the thickness of monolayer was 3.5-4.1nm.

• Korean Journal of Optics and Photonics
• /
• v.8 no.3
• /
• pp.199-203
• /
• 1997

Fine displacement of spherical suface was detected and analyzed by Twyman-Green interferometer and the interferogram analysis using Fourier transform method. The surface profile was obtained from single interferogram by introducing the carrier freguency to the interferogram. The interferogram was processed in the spatial frequency domain by fast Fourier transform, and the phase distribution was obtained by inverse Fourier transform. The 3-dimensional distribution for the surface displacement was obtained. It was compared with the calculated surface displacement and the error was less than λ/10.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.2
• /
• pp.125-133
• /
• 1993

Electronic Speckle Pattern Interferometry(ESPI) using a CW laser, a video system and image processor was applied to the rotating displacement of rigid body. ESPI require no special surface preparation or attachments and displacements between any two arbitrary points on the surface can be measured. The characteristic speckle pattern formed when imaging a scattering surface illuminated by laser light retains phase information, which can be used for interferometric measurement of surface displacement. The application of this principle to measuring in-plane displacement resolved in one direction is described, together with the novel use of television equipment to detect and process the information contained in the speckle pattern. This is faster, and more convenient and versatile than customary photographic methods.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.351-352
• /
• 2010

• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.23-32
• /
• 2003

The displacement measuring systems of slope ground surface are very expensive instruments and have disadvantages concerning installing, maintaining and surveying. The measuring works are very dangerous. Recently, simple systems are required to measure the displacement of slope ground surface in stages of cutting and maintaining slope. In this study, the mechanism of Softcopy Photogrammetry is applied to measure the displacement of slope ground surface. Three dimensional data of the slope ground surface can effectively be obtained in order to analyze slope stability. Computer Program, DIMA (Design IMmage Analysis), including the reformation process of a contour line was developed. As a result of this study, countermeasure and instruction standards of the displacement of slope ground surface before and after slope failure are established. Also, disadvantages of the existing system can be complemented.

• 한국연소학회:학술대회논문집
• /
• 2006.10a
• /
• pp.177-186
• /
• 2006

Flame surface area is a critical parameter determining turbulent flame speed. Three-dimensionaldirect numerical simulations (DNS) were conducted to figure out the evolution process of flame surface area. Fully compressible Navier-Stokes equations are solved to reproduce premixed flame embedded in isotropic decaying turbulent flow. The tangential straining and curvature of propagating surface affect development of flame area. In this study, four different turbulent intensity flows and three different Le number flames are investigated to force changes in straining and curvature effects. Consistent results are obtained for the probability density functions (PDF) of strain and curvature with previous researches. It is revealed that displacement speed, which is a speed of flame surface relative to unburnt flow, controls the balance between sink and source of flame surface area.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.156-159
• /
• 2003

Surface normal vector and surface velocity are very important parameters to simulate rolling processes precisely. In this study, Local displacement functions are constructed for each node on the contact surface and parameters are found by the least square fitting of displacement on the neighbor nodes. Deformation gradient tensor is calculated from the displacement function and surface normal vector and velocity also can be derived. Flat rolling simulation model is presented on the basis of the suggested contact scheme. Series of rolling process simulation are carried out and the results are compared with the experiments.

• Journal of the Korean Society of Combustion
• /
• v.12 no.2
• /
• pp.10-19
• /
• 2007

Flame surface area is a critical parameter determining turbulent flame speed. Three-dimensional direct numerical simulations(DNS) were conducted to figure out the evolution process of flame surface area. Fully compressible Navier-Stokes equations are solved to reproduce premixed flame embedded in isotropic decaying turbulent flow. The tangential straining and curvature of propagating surface affect development of flame area. In this study, four different turbulent intensity flows and three different Le number flames are investigated to force changes in straining and curvature effects. Consistent results are obtained for the probability density functions (PDF) of strain and curvature with previous researches. It is revealed that displacement speed, which is a speed of flame surface relative to unburnt flow, controls the balance between sink and source of flame surface area.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.4 no.3
• /
• pp.10-18
• /
• 2001

The existing measurement system to ground-surface displacement survey of the slope has been including the hazard for the measure in site and the difficulty for install, maintenance and control of expensive instruments, which are impossible of whole survey on the slope surface. To overcome of those defects, Softcopy Photogrammertry method is used, which can measure displacement of ground-surface on the slope and structure deformation vectors. Recently, the survey methods applying the advantages of Photogrammetry and Digital Photogrammetry Survey are widely used. In this study, therefore, the development and application of the new instrument mechanism on the the site example are studied. Through the application of Softcopy Photogrammetry, the 3-D data of ground surface on the dangerous slope could be effectively obtained at the long distance, which are obtained through the reform process of contour line. Those are different to the results of the Close-Range Photogrammetry analysis. In ground instrumentation parts, the new practical system shall be the technical base to improve of the instrument machine as well as can be widely applied in civil engineering and others branch.