• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.3
• /
• pp.477-484
• /
• 2000

Microcontamination caused by particle deposition on the head disk interface threatens the reliability of hard disk drive. Design of slider rail to control contamination becomes an important issue in magnetic recording. In this paper, how particles adhere to the slider and the disk is examined. To investigate accumulation mechanism of the particles, trajectory of the particles in a slider/disk interface is simulated with considering various forces including drag force, gravitational force, Saffman lift force, and electrostatic force. It is found that the charged particles can easily adhere to the slider or disk surface, if an electric field exists between the slider and the disk. It is supposed that the vertical motion of the particles should be related with not only Saffman force but also electrostatic force.

• Journal of environmental and Sanitary engineering
• /
• v.19 no.2
• /
• pp.30-36
• /
• 2004

Dry decontamination technique is required for maintaining nuclear material handling equipment contaminated with highly radioactive material in a hot cell. In order to determine the optimum blasting conditions of dry ice pellet blasting device, the basic experiments have been conducted on the simulated test specimens of four types of metals. The removal efficiency of test piece was evaluated by the XRF analysis and the change of the surface condition before and after blasting. The removal efficiency of cesium on loose contamination was 100% under blasting pressure; 3 kg/$cm^2$, blasting distance; 10 cm, blasting time: 10 sec. In case of fixed contamination, the removal efficiency of cesium was almost 96% under blasting pressure; 4kg/$cm^2$, blasting distance; 10 cm, blasting time; 30 sec.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.6
• /
• pp.474-480
• /
• 2012

Diagnostic tests were performed on two high voltage(HV) motor stator windings. These tests included the measurement of insulation resistance, polarization index, AC current, dissipation factor($tan{\delta}$) and partial discharge(PD) magnitude. Surface contamination of HV motor stator windings has an effect on the AC current and $tan{\delta}$. When the stator windings were finished cleaning and insulation reinforcement, the increase rate of AC current(${\Delta}I$) and dissipation factor(${\Delta}tan{\delta}$) were very small compared to those before cleaning. However, the PD magnitude remained the same. These tests show that cleaning and insulation reinforcement of HV motor stator windings can reduce the insulation failure.

• Journal of Astronomy and Space Sciences
• /
• v.32 no.3
• /
• pp.167-180
• /
• 2015

Herein, we discuss the in situ measurement of the electron temperature in the ionosphere/plasmasphere by means of DC Langmuir probes. Major instruments which have been reported are a conventional DC Langmuir probe, whose probe voltage is swept; a pulsed probe, which uses pulsed bias voltage; a rectification probe, which uses sinusoidal signal; and a resonance cone probe, which uses radio wave propagation. The content reviews past observations made with the instruments above. We also discuss technical factors that should be taken into account for reliable measurement, such as problems related to the contamination of electrodes and the satellite surface. Finally, we discuss research topics to be studied in the near future.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2006.04a
• /
• pp.209-212
• /
• 2006

Using sulfur sotope analysis of dissolved sulfate in surface water, we have investigated the source of sulfate in order to identify the abandoned metallic mines, which have the potential of heavy metal contamination within watershed. The range of the sulfur isotope values for dissolved sulfate in stream waters (DD-1 and 2) are similar to those of sulfides from the Dunjun mine, which suggests that oxidation of sulfides is the principal source of $SO_4^{2-}$ in these stream waters. Also, heavier sulfur isotopes in waters near Baekjun and Hamchang mines imply the possibility of contamination in waters by these metallic mines.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2006.04a
• /
• pp.424-427
• /
• 2006

Soil contamination with petroleum oil around a military army was investigated. It showed that soils of a riverside highland, an entrance of the military army, and nearby roads were contaminated with total petroleum hydrocarbons (TPH) released from the military army to the depth of approximately 2 m. The measured concentrations were as high as 15,277 mg/kg. A wide range of soil in the riverside highland was contaminated by the movement of oil to the surface soil, which occurred with the vertical movement of groundwater table caused by the change of river water level and groundwater level. Spilled petroleum oil components were released into Wonju Stream by the increase of hydraulic conductivity and the groundwater flow.

• Journal of Food Hygiene and Safety
• /
• v.12 no.1
• /
• pp.78-82
• /
• 1997

Surface swab samples from beef (188), pork (240) and chicken (95) carcasses were collected from slaughterhouse in Kangwon and Kyunggi areas from March through July 1996. The samples were examined on the level of E. coli biotype I relevant to fecal contamination due to unsanitary processing control and the existence of verocytotoxin-producing E. coli (VTEC). E. coli biotype I were confirmed from 38.8% of beef, 40.0% of pork, and 69.5% of chicken carcasses. Little variation was noted among three sampling points; rump, flank and neck of beef, ham, belly and jowls of pork. coli O157:H7 was only confirmed from 2 of 188 beef carcasses. E. coli biotype I. All the isolated E. coli O157 showed positive for vero cell cytotoxicity test. Isolation rate of E. coli O157 in summer was higher than in spring. In case of pork and chicken carcasses, E. coli O157 was isolated in summer only.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.04a
• /
• pp.115-119
• /
• 2003

Pollutants from industry, mining, agriculture, and other sources have contaminated sediments in many surface water bodies. Sediment contamination poses a severe threat to human health and environment because many toxic contaminants that are barely detectable in the water body can accumulate in sediment at much higher levels, the purpose of this study was to make convenient sampling method and optimal treatment of sediment for water quality improvement in reservoir or stream based on an evaluation of degree of contamination. Results for analysis of S-reservoir sediments were observed that copper concentration of almost areas were higher than the regulation of soil pollution (50 mg/1) for the riverbed. S-stream sediments were observed that copper, arsenic and TPH concentration of almost areas were exceeded soil pollution concerning levels for factorial areas. We used Remscreen(version. 1.0) program which is contaminated soil recovery program to select optimal treatment method of contaminant sediments. The result was shown in the order of Thermal Calcination > Excavation, Retrieval and Off-site Disposal(comparative less then contaminant) > Low Temperature Thermal Desorption + Solidification/Stabilization.

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.02a
• /
• pp.78-79
• /
• 2001

노광 후 지연(Post Exposure Delay： PED) 효과는 그림 1과 같이 노광 후 지연 시간에 따른 감광제의 Profile에 thinning, T-top, foot, undercut 를 보여주는 현상으로 화학 증폭형 감광제(Chemically Amplified Resist, CAR) 개발에 있어 PED의 안정성은 중요한 요소이다(1). 따라서 노광후 지연 효과에 대한 모델링은 연구와 개발을 위한 시뮬레이션 tool에 있어 매우 의미 있는 일이다. T-top 이나 undercut 를 형성하는 Surface inhibition layer(SIL) 은 노광 후 지연시 발생되는 environmental base contamination, acid evaporation 이 주요 원인이며 다른 원인으로는 감광제 속에서 acid migration, spin coating 동안에 photoacid generator (PAG)의 고갈, internal basic impurities 이며 그 외에 nonbsic atmospheric contamination, high power laser source의 영향 등이 있다. (중략)

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.4
• /
• pp.182-189
• /
• 2001

In this paper, the distribution suspension porecelain insulators which had been used for long periods in the contaminated area were evaluated. The contaminated area is close to the sea and in the high density of industries. The heavily contaminated domestic and imported insulators were investigated by using electrical characteristics, such as power-frequency dry flashover voltage, power-frequency wet, flahover voltage, and leakage current. Also, these electrical results were compared with the contaminants on the surface. From these analysis, we found that the contamination from the industrial dust, only slightly decreased flashover voltage and increased leakage current. Therefore, the electrical properties of insulators used for 30 years in the area of coast and industrial complex were not much changed.