• Tribology and Lubricants
• /
• 제26권1호
• /
• pp.14-20
• /
• 2010

Tribological properties of nanoporous structured alumina film was investigated. Alumina film (AAO: anodic aluminum oxide) of $60{\mu}m$ thickness having nanopores of 45 nm diameter with 105 nm interpore-diatance was fabricated by mild anodization process. Reciprocating ball-on-flat sliding friction tests using 1 mm diameter steel ball as a counterpart were carried out with wide range of normal load from 1 mN to 1 N in an ambient environment. The morphology of worn surfaces were analyzed using scanning electron microscopy. The friction coefficient was strongly influenced by the applied normal load. Smooth layer patches were formed on the worn surface of both AAO and steel ball at relatively high load (100 mN and 1 N) due to tribochemical reaction and compaction of wear debris. These tribolayers contributed to the lower friction at high loads. Extremely thin layer patches, due to mild plastic deformation of surface layer, were sparsely distributed on the worn surface of AAO at low loads (1 mN and 10 mN) without the evidence of tribochemical reaction. Delaminated wear particles were generated at high loads by fatigue due to repeated loading and sliding.

• 아시안잔디학회지
• /
• 제16권1호
• /
• pp.19-30
• /
• 2002

경직된 지반의 물리성 개선재로서 rubber chip의 토양 내 혼합 또는 배토는 잔디의 생육과 지반의 이·화학성 및 중금속 추출 실험을 통하여 다음과 같은 결론을 얻었다. Rubber chip의 토양 내 혼합은 지면의 온도 상승효과를 가져왔으며 이는 겨울철의 동해방지 및 맹아출현기를 앞당길 수 있을 것이라 추정된다. 그러나 복사열이 높은 여름에는 rubber chip에 의한 표면, 지중 온도의 상승으로 잔디의 피해가 우려된다. 또한 토양 내에 rubber chip의 혼합함량(rubber chip 20%, 40%)이 많을수록 잔디의 발아와 생육 및 피복에 부정적인 영향을 끼쳤다. Rubberchip의 토양혼합은 지반의 이·화학성 변화에 크게 작용하지 않았으며 중금속 추출실험에서도 차이를 나타내지 않아 토양환경 오염이 없을 것으로 판단된다. Rubber chip을 배토용 재료로서 사용했을 경우, 경직된 토양구조를 개선시켜 주었다. 특히 통기작업 후 rubber chip의 배토는 지반의 표면탄성을 현저히 완화시켰다. 따라서 현재 우리나라에서 보수중이 거나 건설중인 연습구장, 보조구장에 재활용이 가능한 폐타이어 rubber chip을 지반 답압 개선용, 배토용 재료로서 사용이 가능할 것으로 판단된다.

• 한국도로학회논문집
• /
• 제3권2호
• /
• pp.103-112
• /
• 2001

본 연구는 재생골재를 도로의 보조기층재료 및 포장용 콘크리트 골재로 사용하기 위하여 수행되었다. 우선 보조기층재료로서의 활용성 여부를 파악하기 위하여 실내다짐시험, CBR 시험, 평판재하시험을 수행하였으며, 콘크리트용 골재로의 활용성을 보기 위하여 재생골재 첨가비율을 0, 20, 40, 60, 80%로 하여 설계기준강도 $280kgf/cm^2$인 표층용 콘크리트를 제조하였다. 제조된 콘크리트로 굳지 않은 콘크리트 성질과 28일 양생 후 강도시험과 동결 융해에 따른 내구성 시험을 통해 폐콘크리트 재생골재의 활용성을 도로포장재료 측면에서 검토하였다. 실험결과 재생골재는 보조기층재료로서의 사용이 충분히 가능하며 표층용 콘크리트 골재로서 재생골재 첨가비율 40%까지 활용이 가능함을 알 수 있었다.

• 한국세라믹학회지
• /
• 제33권9호
• /
• pp.1057-1063
• /
• 1996

Y2O3-CeO2-ZrO2 powders were prepared from water-soluble salts using a coprecipitation method. The forming process of oxide and the characteristics of the calcined powders treated in different drying conditions were investigated. The oxidation was occurred at the temperature of around 40$0^{\circ}C$ and the main crystallization of ZrO2 around $600^{\circ}C$. On calcination at $600^{\circ}C$ heating lamp-dried powders consisted of agglomerates of globular morphology with average agglomerate size of 2.27${\mu}{\textrm}{m}$ and specific surface area of 68.3m2/g and spray dried powders contained dense spheric particles with average agglomerate size of 1.35${\mu}{\textrm}{m}$ and specific surface area of 11.0m2/g which exhibited low agglomeration tendency. Removal of the water by a freeze-drying technique produced calcined powders containing flake-like secondary particle structures with wide agglomerate size distri-bution of 0.1-60${\mu}{\textrm}{m}$ and specific surface area of 24.5${\mu}{\textrm}{m}$. The 20 MPa-pressed density (36.8-41.4% T,D) of calcined powders did not nealy depend on drying methods whilst compaction ratio of calcined powders derived from freeze-drying was the highest ( 6.24) among three drying methods. On continuous heating up to 150$0^{\circ}C$ the sinterability of calcined powders derived from heating lamp-drying was superior to those derived from spray-and freeze-drying. The final sintered density of calcined powders was the highest (96% T,D at 150$0^{\circ}C$) in case of heating lamp-drying.

• 펄프종이기술
• /
• 제30권3호
• /
• pp.74-83
• /
• 1998

The phenomenon of decrease in sizing efficiency when the stock temperature is increased is well recognized as summer sizing, and this is believed to be caused by uneven distribution of sizing agents on paper surface most often incurred by coagulation of sizing agents. When unevenly sized paper is used as coating base stock, nonuniform consolidation of the coating layer may result, which, in turn, causes uneven distribution of binder on coating surface. This causes nonuniform ink absorption to produce print mottle. In this study the effects of simple or polymeric electrolytes, storage temperature and time on the coagulation of cationic dispersed rosin size were investigated using a turbidity measurement method which was verified to correlate well with the particle size of rosin emulsion or its coagulates. Handsheets sized with rosin dispersions coagulated under various conditions were prepared and their sizing degree and coated paper properties including gloss and ink density were examined. The relationship between the sizing nonuniformity of coated papers and its ink absorption property was evaluated. Turbidity of rosin emulsion increased as the storage temperature and time were increased. Addition of simple or polymeric electrolytes caused reduction in $zeta$ -potential of the rosin dispersion and accelerated the coagulation tendency substantially. Reversion of the $zeta$ -potential of rosin dispersion, however, did not occur when coagulation was induced with simple electrolytes. On the other hand, addition of an anionic polyelectrolyte reversed the $zeta$ -potential of the flocculated rosin dispersion. This indicated that electrical double layer compaction and bridging flocculation were coagulation mechanisms for simple and polymeric electrolytes, respectively. Sizing degree decreased as coagulation of rosin was increased. Paper gloss, ink gloss and ink density were increased when sizing degree of base stock was increased most probably due to prevention of base paper swelling and increased binder migration to coating surface. This suggested that uneven printing ink density occurred when uneven sizing development was induced by coagulation of rosin particles.

• 한국토양비료학회지
• /
• 제42권Spc호
• /
• pp.40-44
• /
• 2009

이 연구는 Rock-dust로 채워진 농업 용지(Technosol)의 환경에서 물이 보이는 침투성과 삼투성의 특정을 파악하고자 수행되었다. 이 실험은 A와 B 두 장소에서 이루어졌으며 피실험지의 토양층은 각각 4가지 층으로 분류되었다. 모든 토양층의 토성은 미사질 양토로 분석되었으며 장소 A의 가장 낮은 층에서만은 양질사토였다. 두 토양에서, 각 토양층에 대한 용적밀도는 $1.49g{\cdot}cm^{-3}$을 대체로 상회하였으며, 이는 통상적인 medium textured mineral soil의 $1.25g{\cdot}cm^{-3}$을 크게 웃도는 값이다. 경운 직후 측정된 장소 A의 표토는 이보다 낮았다. 두 토양 표면에서의 $P_2O_5$의 집적은 각각 1962 (A), 1613 (B)$mg{\cdot}kg^{-1}$이었다. 이러한 집적은 3.2~6.5번에 걸쳐서 $300{\sim}500mg{\cdot}kg^{-1}$만큼 작물 생장에 알맞은 규모로 이루어졌다. 두 토양 표변에서의 Infiltration rate는 3.54 (A), 2.85 (B)$cm{\cdot}hr^{-1}$이었으나 각 토양층에 대한 percolation rate는 0.3 이하 (A), 0.003 이하 (B)$cm{\cdot}hr^{-1}$였다. 이러한 결과들은 표토가 동의 작용을 받은 반면 심토는 암분의 농업용지 형성 과정에서 생겨난 구조적인 문제인 바위 부스러기의 응집과 농업기계에 대한 다짐현상으로 인한 것임을 의미한다고 여겨진다.

• Corrosion Science and Technology
• /
• 제9권3호
• /
• pp.129-136
• /
• 2010

The corrosion behaviors of 316L stainless steel were investigated in simulated anodic and cathodic environments for proton exchange membrane fuel cell (PEMFC) by using electrochemical measurement techniques. Interfacial contact resistance(ICR) between the stainless steel and gas diffusion layer(GDL) was also measured. The possibility of 316L was evaluated as a substitute material for the graphite bipolar plate of PEMFC. The value of ICR decreased with an increase in compaction stress(20 N/$cm^2$~220 N/$cm^2$) showing the higher values than the required value in PEMFC condition. Although 316L was spontaneously passivated in simulated cathodic environment, its passive state was unstable in simulated anodic environment. Potentiostatic and electrochemical impedance spectroscopy (EIS) measurement results showed that the corrosion resistance in cathodic condition was higher and more stable than that in anodic condition. Field emission scanning electron microscopy (FE-SEM), and inductively coupled plasma(ICP) were used to analyze the surface morphology and the metal ion concentration in electrolytes.

• Geomechanics and Engineering
• /
• 제12권1호
• /
• pp.85-109
• /
• 2017

The paper presents the laboratory study of clayey soil stabilized with Pond ash (PA), Rice husk ash (RHA), cement and their combination used as stabilizers to develop and evaluate the performance of clayey soil. The effect of stabilizer types and dosage on fresh and mechanical properties is evaluated through compaction tests, unconfined compressive strength tests (UCS) and Split tensile strength tests (STS) performed on raw and stabilized soil. In addition SEM (scanning electron microscopy) and XRD (X-ray diffraction) tests were carried out on certain samples in order to study the surface morphological characteristics and hydraulic compounds, which were formed. Specimens were cured for 7, 14 and 28 days after which they were tested for unconfined compression tests and split tensile strength tests. The moisture and density curves indicate that addition of RHA and pond ash results in an increase in optimum moisture content (OMC) and decrease in maximum dry density (MDD). The replacement of clay with 40% PA, 10% RHA and 4% cement increased the strength (UCS and STS) of overall mix in comparison to the mixes where PA and RHA were used individually with cement. The improvement of 336% and 303% in UCS and STS respectively has been achieved with reference to clay only. Developed stabilized soil mixtures have shown satisfactory strength and can be used for low-cost construction to build road infrastructures.

• International Journal of Contents
• /
• 제14권3호
• /
• pp.53-60
• /
• 2018

Based on the previous studies on sinkholes and ground subsidence conducted until date, the factors affecting the occurrence of sinkholes can be divided into natural environmental factors and human environmental factors in accordance with the purpose of the study. Furthermore, to be more specific, the human environment can be classified into the artificial type and the social type. In this study, the assessment indices for assessing risks of sinkholes and ground subsidence were developed by performing AHP analysis based on the results of the study by Lee et al. (2016), who selected the risk factors for the occurrence of sinkholes by performing Delphi analysis targeting relevant experts. Analysis showed that the artificial environmental factors were of significance in affecting the occurrence of sinkholes. Explicitly, the underground factors were found to be of importance in the natural environment, and among them, the level of underground water turned out to be an imperative influencing factor. In the artificial environment, the underground and subterranean structures exhibited similar importance, and in the underground structures, the excessive use of the underground space was found to be an important influencing factor. In the subterranean ones, the level of water leakage and the erosion of the water supply and sewage piping system were the influential factors, and in the surface, compaction failure was observed as an imperative factor. In the social environment, the regional development, and above all, the groundwater overuse were found to be important factors. In the managemental and institutional environment, the improper construction management proved to be the most important influencing factor.

• 한국지반신소재학회논문집
• /
• 제8권4호
• /
• pp.35-40
• /
• 2009

본 논문에서는 순환골재 다공질 콘크리트말뚝(RAPP : Recycled-Aggregate Porous Concrete Pile)에 의한 압밀촉진효과를 파악하기 위하여 일련의 실내모형실험을 수행하였다. 본 연구에서 얻어진 실험 결과를 동일한 조건에서 수행한 모래다짐말뚝과 쇄석다짐말뚝에 대한 기존의 실험결과(유승경, 2009)와 비교하여 RAPP로 개량된 복합지반의 시간에 따른 침하량의 변화 특성과 압밀시간에 대하여 비교, 분석하였다. 또한 일련의 수치해석을 수행하여 실내모형실험 결과를 평가하였다. 분석 결과로부터 RAPP에 의한 일차압밀과 이차압밀에 대한 침하저감효과가 타 공법에 비해 탁월함을 알 수 있었으며 압밀 종료시간도 상대적으로 빠르게 나타나 RAPP에 의한 압밀촉진효과가 우수함을 입증할 수 있었다.