• Progress in Superconductivity and Cryogenics
• /
• v.1 no.2
• /
• pp.37-42
• /
• 1999

The stability of high-temperature superconducting current leads for cryogenic devices are investigated. By assuming full transition from superconducting state to normal state at a transition temperature, the HTS current at a transition temperature, the HTS current lead shows bifurcation phenomenon. There is a bifurcation shape-factor, HTS leads have three steady state. Below the bifurcation shape-factor, the superconducting current lead is unconditionally stable, because there exists only one steady-factor HTS current lead is conditionally stable depending on the shape and intensity of disturbance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.10
• /
• pp.943-949
• /
• 2008

We report on the development of transition edge sensors for x-ray detection. The sensor technology was based on the fabrication of a superconducting film on a thin membrane. A bilayer of a superconductor, Ti, and a noble metal, Au, was e-beam evaporated on a micromachined SiNx. Another Au layer was evaporated on the two side edges of the bilayer in order not to be affected by structural imperfections at the boundaries. With the method described in the present report, the superconducting transition temperature of the device was consistently achieved to near 80 mK with a sharp transition. The energy spectrum ueasured with the device provided 37 eV FWHM for 5.9 x-rays. We also discuss the design and fabrication considerations as well as the performance of the device in detail.

• 한국초전도학회:학술대회논문집
• /
• 2008.08a
• /
• pp.10-10
• /
• 2008

• Progress in Superconductivity
• /
• v.9 no.2
• /
• pp.162-166
• /
• 2008

We are developing a sensitive gamma ray spectrometer based on superconducting transition edge sensors. The detector consists of a small piece of high purity Sn as an absorber and a Ti/Au bilayer as a temperature sensor. It is designed to measure the thermal signal caused by absorption of gamma rays. The mechanical support and the thermal contact between the absorber and the thermometer were made with Stycast epoxy. The bilayer was formed by e-beam evaporation and patterned by wet etching on top of a $SiN_X$ membrane. A sharp superconducting transition of the film was measured near 100 mK. When the film was biased to the edge of the transition, signals were observed due to single photon absorption emitted from an $^{241}Am$ source. The measured spectrum showed several characteristic peaks of the source including 59.5 keV gamma line. The full with at half maximum was about 900 eV for the 59.5 keV gamma line. The background was low enough to resolve low energy lines. Considerations to improve the energy resolution of the gamma ray spectrometer are also discussed.

• Progress in Superconductivity
• /
• v.14 no.1
• /
• pp.34-38
• /
• 2012

The effect of graphene inclusion in the ex-situ $MgB_2$ was analyzed with the help of resistivity behavior and critical current density studies. Amount of graphene was systematically varied from 0% for pristine sample to 3% by the weight of $MgB_2$. Graphene that is considered as a good source of carbon was found to be intact without any significant carbon doping in $MgB_2$ structure as reveled by XRD measurements. There was no signature of graphene inclusion as far as the superconducting transition is concerned which remained same at 39 K for all the samples. The transition width being sensitive to defect doping remained more or less about 2 K for all the samples showing no variation due to doping. Although there was no change in the superconducting transition or transition width, the graphene doped sample showed noticeable decrease in the overall resistivity behavior with respect to decrease in temperature. The graphene inclusion acted as effective pinning centers which have enhanced the upper critical field of these samples.

• Progress in Superconductivity and Cryogenics
• /
• v.16 no.1
• /
• pp.23-26
• /
• 2014

This paper represents the detection method of voltage disturbance for high temperature superconducting (HTS) tape using electromagnetically coupled coils. In order to detect the voltage as the superconductor transits from the superconducting state to the normal conduction state, voltage taps are widely used to get the voltage signal. And voltage taps are connected to data acquisition device via signal wires. However this new suggested method can detect the superconducting transition voltage without signal wires between voltage taps and data acquisition device by using electromagnetically coupled coils. This system consists of two electromagnetically coupled coils, the first coil to detect and transmit the voltage of HTS tape and the second coil to pick up the transmitted voltage from the first coil. By using this new suggested method, we can build the 'separated voltage-detection system'. HTS tape and first coil are located under liquid nitrogen vessel and the second coil is located under room temperature condition. In this paper, experiments are performed to verify the feasibility of the proposed method. As the result of the experiment, the separated voltage-detection system using electromagnetically coupled coils can successfully observe superconducting-normal transition of HTS tapes.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.2
• /
• pp.451-454
• /
• 2011

The traditional BCS superconductors $AOs_2O_6$ (A=K, Rb, and Cs) were investigated to find the relationship between their structures and superconducting transition temperatures. The $T_c$ decreases with increasing the unit cell parameter of $AOs_2O_6$. This is in contrast to the case of conventional BCS superconductivity in a single bond model, where $T_c$ may increase with increasing the the unit cell parameter since the DOS at Fermi level increases as the unit cell parameter increases. Instead, the $T_c$ of a $\beta$-pyrochlore oxide is proportional to the lattice softness of the compound.

• Analytical Science and Technology
• /
• v.5 no.2
• /
• pp.223-228
• /
• 1992

$Bi_2Sr_2Ca_2Cu_3Oy$-based superconductor phases were synthesized by the wet process using acetate precursors. Superconducting transition temperature ($T_c$) was determined from both measurements of electrical resistivity and magnetic susceptibility for the samples which were sintered at the temperatures of $850^{\circ}C$, $860^{\circ}C$, and $870^{\circ}C$ for 40 hours, respectively. The values of carrier concentration from Hall measurements were compared with $T_c$ data as a function of the sintering temperature. The formation mechanism of the superconducting phase was tentatively discussed on a basis of the distribution profile concept of the carrier concentration and the amount of superconducting phases in a ceramic bulk. This explanation may be supported by the experimental results of correlation between the relative amount of superconducting phases and the difference of $T_c$ values between superconducting onset temperature and cutoff temperature at each sintering temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.794-797
• /
• 2000

The fabrication of high quality superconducting thin films using pulsed laser deposition (PLD) has been reported to find optimized processing conditions and to make the millimeter-wave devices. High temperature superconducting (HTS) YBCO films were prepared on MgO (10${\times}$10${\times}$0.5mm) substrates by the PLD. The 3 pole bandpass filter with the center frequency of 22 GHz for satellite communication was designed consisting of hairpin coupled-lines to reduce the configuration in size. YBCO films are c-axis oriented and show superconductive transition temperatures of 88∼89 K with the transition widths < 0.5 K. The insertion loss of passband at 70 K was about 5 dB. The measured frequency response of superconducting filter will be compared with the simulation result.

• Progress in Superconductivity and Cryogenics
• /
• v.20 no.2
• /
• pp.24-28
• /
• 2018

To understand the effects of Cd substitution for Cu, $(Pb_{0.5}Cu_{0.5-x}Cd_x)Sr_2(Ca_{0.7}Y_{0.3})Cu_2O_z$ (x = 0 ~ 0.5) compounds were synthesized and the structural and superconducting properties of the compounds were characterized. Resistivity data revealed that superconducting transition temperature rises initially up to x = 0.25 and then decreases as the Cd doping content increases. Room-temperature thermoelectric power decreases at first up to x = 0.25 and then increases with higher Cd doping content, indicating that the change in $T_c$ is mainly caused by the change in the hole concentration on the superconducting planes by the Cd doping. The non-monotonic dependence of the lattice parameters and the transition temperature with Cd doping content is discussed in connection with the possible formation of $Pb^{+2}$ ions and the removal of excess oxygen caused by Cd substitution in the charge reservoir layer. A correlation between transition temperature and c/a lattice parameter ratio was observed for the $(Pb_{0.5}Cu_{0.5-x}Cd_x)Sr_2(Ca_{0.7}Y_{0.3})Cu_2O_z$ system.