• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 1999.02a
• /
• pp.34-38
• /
• 1999

An acoustic emission(AE) technique has been used to monitor and diagnose quenching phenomenon in racetrack shaped superconducting magnets at cryogenic environment of 4.2K. The ultimate goal is to ensure the safety and reliability of large superconducting magnet systems by being able to identity and locate the sources of quench in superconducting magnets. The characteristics of AE parameters have been analyzed by correlating with quench number, winding tension of superconducting coil and charge rate by transport current. It was found in this study stat there was good correlation between quench current and AE parameters. The source location of quenching in superconducting magnet was also discussed on the correlation between magnet voltage and AE energy.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.8
• /
• pp.521-527
• /
• 1988

At present superconducting magnets have been feasible for many applications which require high field or highly homogeneous field that it is too difficult to be produced by conventional electromagnets. This paper is a stuny on Donble Helmholtz superconducting magnet and newly configurated superconducting magnet that realize highly homogeneous field with the minimum magnet volume. Nonlinear programming method is effectively used for the minimum volume of superconducting magnet that realizes the desired field intensity and high homogeneity. The results on Double Helmholtz and newly configurated superducting magnets that are presented in this paper are largely improved.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.1
• /
• pp.59-64
• /
• 2006

A closed-loop cryogenic cooling system for high field magnets is presented. This design is motivated by our recent development of cooling system for 21 tesla Fourier Transform ion Cyclotron Resonance (FT-ICR) superconducting magnets without any replenishment of cryogen. The low temperature superconducting magnets are immersed in a subcooled 1.8 K bath, which is connected hydraulically to the 4.2 K reservoir through a narrow channel. Saturated liquid helium is cooled by Joule-Thomson heat exchanger and flows through the JT valve, isenthalpically dropping its pressure to approximately 1 6 kPa, corresponding saturation temperature of 1.8 K. Helium gas exhausted from pump is now recondensed by two-stage cryocooler located after vapor purify system. The amount of cryogenic Heat loads and required mass flow rate through closed-loop are estimated by a relevant heat transfer analysis, from which dimensions of JT heat exchanger and He II heat exchanger are determined. The detailed design of cryocooler heat exchanger for helium recondensing is performed. The effect of cryogenic loads, especially superfluid heat leak through the gap of weight load relief valve, on the dimensions of cryogenic system is also investigated.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.89-91
• /
• 1996

In dry-winding(unfilled) superconducting magnets, the behavior of liquid helium occupying the extremely small void space within the winding is contributed as a primary factor for transient stability of magnets. Therefore, numerical experiments have been carried out concerning the influences of transient heat transfer of liquid helium ocupying the void space in the winding and thermal properties of insulation at the conductor surface on the transient stability of magnets, by using three-dimensional finite element method(FEM). In this paper, we are going to consider three different cases for heat transfer characteristics of liquid helium to observe the influences of the rest of liquid helium in void space within the winding on the transient stability.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1992.11a
• /
• pp.35-38
• /
• 1992

The feasibility of magnetohydrodynamic (MHD) Ship propulsion using superconduction magnets is reviewed in light of recent advances in high-temperature superconducting. The propulsion using a screw propeller in the noise reduction has it's own limitation. The epochal noiseless MHD propulsion method which does not have this disadvantage is studying nowadays. The subject of a marine MHD as propulsion has been examined before and was found to be interesting because of relatively low magnetic flux densities. It is demonstrated that the MHD propulsion is technically interesting with high magnetic flux density. The development of large-scale magnets using the high-temperature superconductors now under development could make it practical to construct submersibles for high-speed and silent operation.

• Progress in Superconductivity and Cryogenics
• /
• v.18 no.2
• /
• pp.37-41
• /
• 2016

This paper presents the developed quench analysis code and protection circuit design for a superconducting magnet system of 28GHz electron cyclotron resonance (ECR) ion source. The superconducting magnet is composed of a hexapole magnet and four solenoid magnets located outside of the hexapole one. All magnets are wound with NbTi composite wire and impregnated by epoxy. By using the developed characteristic analysis code, the normal zone resistance, decaying current and temperature rising can be estimated during quench. Also, the stored magnetic energy is successfully consumed from the series resistor of the designed protection circuit. The analytical results are compared with the experimental results to verify the developed quench analysis code and protection circuit.

• Progress in Superconductivity and Cryogenics
• /
• v.20 no.2
• /
• pp.20-23
• /
• 2018

The practical use of superconducting magnets is limited to medical equipment, energy equipment and the like. Therefore, it does not fully utilize the superior features of superconducting magnet or magnetic force. In order to overcome this blockage condition, The international Forum on Magnetic Force Control (IFMFC) was launched in Tokyo in 2010 by the magnetic separation researchers in Japan, Korea and China. The policy is to hold around the country every year, to apply the application to the engineering field of magnetic force utilization and information exchange about the development of applied science to mutual visit of researchers and to develop the application field of superconducting magnets in particular. The main object is to review the field of application of magnetic force with respect to published papers at 8 IFMFCs, and to introduce the trend of research forum utilizing strong magnetic force which is rare in the world. The United Nations is asking each country to achieve Corporate Social Responsibility (CSR) targets for 2030. This IFMFC review will be utilized in this field.

• Progress in Superconductivity and Cryogenics
• /
• v.7 no.4
• /
• pp.28-31
• /
• 2005

To verify the feasibility of bifilar winding type superconducting fault current limiter (SFCL) using BSCCO tape, two types of magnets were fabricated and tested by short-circuit in this research. Even if the FCL using high Tc superconducting (HTS) tape has zero resistance in normal state, it needs to be wound as a bifilar winding for zero inductance. Solenoid type and pancake type bifilar winding magnets are designed and fabricated with the same length of BSCCO tape. The test system consists of AC power supply, transformer, fault switch, load and bifilar winding magnet. The applied AC voltages during fault duration, 0.1s, were from 0.5V to 20V. The test results without bifilar winding magnet were compared with those with each type magnets. The test results include voltage against magnet, transport current and generated resistance curve. Thermal stability, the recovery time, was studied from the results of two type magnets. The pancake type was the most effective to limit fault current but the solenoid type was thermally the most stable. From this research, short-circuit characteristics of the two types were obtained.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.7
• /
• pp.1067-1074
• /
• 1994

This paper deals with the combined levitation and guidance EDS(Electrodynamic Suspension) Maglev system. Levitation and guidance forces generated in figured-of-eight coil are examined. End effect of Superconducting magnets is considered in that the air gap flux has been calculated using the finite number of magnets. Induced emfs and currents of ground coils are given as results. Eletromagnetic forces vary according to the built-in position of magnets. Levitation forces of the first magnet pair are the smellest and those of the second one are the largest. This result shows that the end effect of SCMs should be considered in a concentrated magnet system.

• Journal of Welding and Joining
• /
• v.14 no.5
• /
• pp.122-133
• /
• 1996

In order to evaluate the cryogenic fracture characteristics of structural steels for superconducting magnets of fusion reactor, small punch (SP) testing was performed on austenitic stainless steel (JN1 base metal) and its TIG weldments at 293K, 77K and 4K. The mechanical properties with respect to the extracted location of the weld metal, on the effects of welding heat cycle about base metal near fusion line in TIG weldments were investigated. The mechanical property of the weld metal in TIG weldments depends on distance from welding root, root region of weldments having the lowest mechanical property. The base metal near fusion line showed degradation of mechanical property caused by cyclic heating during the TIG welding. Based on the test results, HAZ was found to be up to 5mm from the fusion line. It is shown that SP testing is a useful tool to evaluate the mechanical properties with respect to the microstructures changes such as HAZ as well as weld metal in TIG weldments at cryogenic temperature.