• 생물환경조절학회지
• /
• 제7권1호
• /
• pp.55-61
• /
• 1998

본 실험은 배양액 내의 황산이온이 참쑥(Artemisia mongolica var. tenuifolia)의 생육에 미치는 영향을 알아보고자 수행되었다. 황산이온은 0, 0.5, 1, 2, 3mM의 농도로 처리되었는데 양액은 벨기에의 채소연구소에서 허브용양액으로 개발된 양액조성을 변형하여 이용하였다. 참쑥의 생육은 일반적으로 3mM 처리에서 좋았으며 건물률 또한 3mM 처리에서 가장 좋았다. 배양액내의 황산이온 농도가 증가할수록 참쑥의 엽록소 함량은 증가하였는데 특히 엽록소 a의 함량이 b함량에 비해 증가의 폭이 컸다. 참쑥의 무기물 함량은 배양액내의 황산이온 농도와 유의성을 보이지 않았으나 조직내 Ca의 함량은 3mM 처리에서 급격히 감소하였다. 식물에 의한 황산이온의 흡수는 배양액내의 농도가 증가할수록 증가하였는데 2mM까지는 서서히 증가 하다가 3mM에서 현저하게 증가하였다. 1mM 황산이온 처리에서 정유의 함량은 가장 높았으나 그 이상으로 농도가 증가할 경우 정유의 함량은 오히려 감소하였다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제19권4호
• /
• pp.601-604
• /
• 2006

The objective of this study was to investigate technical methods for extraction of mucopolysachharide-protein containing chondroitin sulfate from keel cartilage of chickens. The chemical composition of chicken keel cartilage was determined. For the preparation of mucopolysaccharide-protein from lyophilized chicken keel cartilage, hot water extraction and alcalase hydrolysis methods were examined. Results showed that the optimum condition of hot water extraction was incubation for 120 min with a yield of 40.09% and chondroitin sulfate content of 28.46%. For alcalase hydrolysis, the most effective condition was 2% alcalase in 10 volumes of distilled water for 120 min. The yield of hydrolysate was 75.87%, and chondroitin sulfate content was 26.61%. For further separation of chondroitin sulfate from the alcalase hydrolysate, which has a higher yield than that of hot water, 60% ethanol precipitation was performed. The yield of the ethanol precipitate was 21.41% and its chondroitin sulfate content was 46.31%. The hot water extract, alcalase hydrolysate and ethanol precipitate showed similar electrophoretic migration with standard chondroitin sulfate (chondroitin sulfate A), using cellulose acetate membrane electrophoresis. These results indicated that a significant amount of mucopolysaccharide-protein containing chondroitin sulfate could be acquired form chicken keel cartilage. Therefore, keel cartilage in chicken may provide an inexpensive source of chondroitin sulfate for commercial purposes.

• 한국세라믹학회지
• /
• 제44권9호
• /
• pp.465-470
• /
• 2007

This paper presents an experimental study of the sulfate resistance of mortars and pastes exposed to sodium sulfate solutions up to one year. In order to check deterioration modes due to sulfate attack, the sodium sulfate solution was varied at three concentration steps (3,380, 10,140 and 33,800 ppm of $SO_4^{2-}$ ions), and maintained at ambient temperature. The tests include a visual examination, expansion and compressive strength loss measurements as well as x-ray diffraction tests. The experimental data indicated that the use of cement with a low $C_3A$ content and low silicate ratio has a beneficial effect on the sulfate attack of mortars. In contrast, the mortars with a high $C_3A$ content and high silicate ratio became severely degraded due to the formation of ettringite, gypsum and/or thaumasite in the cement matrix.

• 대한치과보철학회지
• /
• 제28권1호
• /
• pp.137-163
• /
• 1990

The properties of a investment material can be described by the consistency at the slurry state, the setting time, the compressive strength and the thermal expansion during the casting. In this study the effect of the production parameters which are included the ratio of quartz and cristobalite, the content of binder, the water powder ratio and the content and concentration of additives on the Properties of the gypsum-bonded investments has been investigated with help of the consistency test, the vicat needle test, the compressive strength test, the thermal expansion test, x-ray diffraction and DTA thermal differential test. The experimental results showed that the constitution of a investment with W/P ratio of 0.34, 30% of gypsum, 0.8% aluminium sulfate, 2% magnesium sulfate, 0.6% sodium phosphate was adapted for the properties of the KDA Spec. No. 13 type I investment. The important experimental results are summarized as follows. 1. The consistency of the investment decreased with increasing amount of aluminium sulfate and decreasing amount of sodium phosphate. An addition of magnesium sulfate up to 2% an increase of the consistency was shown. But 3% magnesium sulfate in investment showed a decrease of the consistency. The consistency did not vary significantly with a variation of the content of gypsum and cristobalite and the W/P ratio. 2. Aluminium sulfate and the magnesium sulfate promoted the hardening and the aluminium phosphate delayed the hardening. The setting time increased with amount of gypsum. The effect of the matrix on the setting time was insignificant. With the W/P ratio of 0.34 the setting time was 14 min. 3. The compressive strength decreased with the amount of aluminium sulfate up to 0.25% and increased with the amount of aluminium sulfate greater than 3%. The compressive strength decreased as decreasing the amount of magnesium sulfate and gypsum and as increasing the W/P ratio. The effect of the refractory on the compressive strength was also not significant. With the W/P ratio of 0.34 the compressive strength was $34Kg/mm^2$. 4. The 1st thermal expansion was found at the temperature near and the steady state or the contraction stage was found at the temperature between $250^{\circ}C$ and $500^{\circ}C$. After this stage the 2nd thermal expansion took place at the temperature near $500^{\circ}C$. The amount of thermal expansion increased with decreasing the content of magnesium sulfate, aluminium sulfate and gypsum and the W/P ratio. And the amount of thermal expansion increased as the content of sodium phosphate and cristobalite. With the W/P ratio of 0.34 the amount of total expansion was 1.2%.

• 대한치과보철학회지
• /
• 제29권1호
• /
• pp.139-165
• /
• 1991

The properties of a investment material can be described by the consistency at the slurry state, the setting time, the compressive strength and the thermal expansion during the casting. In this study the effect of the production parameters which are included the ratio of quartz and cristobalite, the content of binder, the water powder ratio and the content and concentration of additives on the properties of the gypsum-bonded investments has been investigated with help of the consistency test, the vicat needle test, the compressive strength test, the thermal expansion test, x-ray diffraction and DTA thermal differential test. The experimental results showed that the constitution of a investment with W/P ratio of 0.34, 30% of gypsum, 0.8% aluminium sulfate, 2% magnesium sulfate, 0.6% sodium phosphate was adapted for the properties of the KDA Spec. No. 13 type I investment. The important experimental results are summarized as follows. 1. The consistency of the investment decreased with increasing amount of aluminium sulfate and decreasing amount of sodium phosphate. An addition of magnesium sulfate up to 2% an increase of the consistency was shown. But 3% magnesium sulfate in investment showed a decrease of consistency. The consistency did not vary significantly with a variation of the content of gypsum and cristobalite and the W/P ratio. 2. Aluminium sulfata and the magnesium sulfate promoted the hardening and the aluminium phoshpate delayed the hardening. The setting time increased with amount of gypsum. The effect of the matrix on the setting time was insignificant. With the W/P ratio of 0.34 the setting time was 14 min. 3. The compressive strength decreased with the amount of aluminium sulfate up to 0.25% and increased with the amount of aluminium sulfate greater than 3%. The compressive strength decreased as decreasing the amount of magnesium sulfate and gypsum and as increasing the W/P ratio. The effect fo the refractory on the compressive strength was also not significant. With the W/P ratio of 0.34 the compressive strength was $34Kg/mm^2$. 4. The 1st thermal expansion was found at the temperature near $250^{\circ}C$ and the steady state or the contraction stage was found at the temperature between $250^{\circ}C$ and $500^{\circ}C$. After this stage the 2nd thermal expansion took place at the temperature near $500^{\circ}C$. The amount of thermal expansion increased with decreasing the content of magnesium sulfate, aluminium sulfate and gypsum and the W/P ratio. And the amount of thermal expansion increased as the content of sodium phosphate ad cristobalite. With the W/P ratio of 0.34 the amount of total expansion was 1.2%.

• Advances in concrete construction
• /
• 제11권3호
• /
• pp.183-192
• /
• 2021

Due to economic and environmental benefits, increasing the substitution ratio of ordinary cement by industry by-products like fly ash (FA) is one of the best approaches to reduce the impact of the concrete industry on the environment. However, as the substitution rate of FA increases, it will have an adverse impact on the performance of cement-based materials, so the actual substitution rate of FA is limited to around 10-30%. Therefore, in order to increase the early-age strength of high replacement (30-70%) low-calcium ultrafine FA blended cement paste, sodium sulfate and calcium sulfate dihydrate were used to improve the reactivity of FA. The results show that sodium sulfate has a significant enhancement effect on the strength of the composite pastes in the early and late ages, while calcium sulfate dihydrate has only a slight effect in the late ages. The addition of sodium sulfate in the cement-FA blended system can enhance the gain rate of non-evaporation water, and can decrease the Ca(OH)2 content. In addition, when the sulfate chemical activators are added, the ettringite content increases, and the surface of the FA is dissolved and hydrated.

• 한국방사선학회논문지
• /
• 제14권5호
• /
• pp.627-634
• /
• 2020

본 연구는 기존의 납을 대신해 친환경 물질인 황산바륨과 3D 프린터 소재인 PLA 필라멘트를 혼합하여 형태학적 구현을 위한 차폐체를 개발하고자 하였다. 환경 물질인 황산바륨 분말 가루와 3D프린터 소재인 PLA 필라멘트를 사용하였으며, 황산바륨 분말 가루와 PLA를 혼합하기 위하여 압출기로 융합 후 3D 프린터로 차폐체를 제작하였다. 황산바륨 파우더 분말 가루와 PLA 필라멘트 혼합비율을 확인하기 위해 혼합입도를 분석하였으며, 혼합된 차폐체의 차폐능을 확인하기 위해 황산바륨 함유량에 따른 두께별 흡수선량을 구하여 선량을 평가한 후 차폐능을 분석했다.황산바륨 분말 입자와 PLA 필라멘트 혼합 입도 평가 시 외관상과 주사전자현미경 관찰사진에서 함유량이 30%일 때 가장 적정비율로 혼합된 것을 확인하였다. 황산바륨 함유량에 따른 두께별 흡수선량 결과에서 함유량이 0%일 때와 각 % 별 함유량을 비교했을 때 두께 0.5 cm에서 흡수선량의 차이가 가장 크게 나타났으며, 바륨함유량이 30%일 때 두께 3 cm에서 가장 낮은 선량값을 나타냈다. 또한 바륨함유량이 30%를 기점으로 함유량이 증가할수록 흡수 선량값은 다시 높아지는 결과가 나타났다. 기존의 납 대신 친환경 물질인 황산바륨을 필라멘트 소재인 PLA와 혼합하여 형태학적인 차폐체를 만들 수 있었다. 혼합물에 대한 바륨의 혼합비율은 30%가 가장 적절하며, 본 연구를 토대로 진단 방사선 분야 내 3D 프린터를 이용한 형태학적 차폐체 구현을 위한 기초 자료로 사용될 것으로 기대한다.

• 한국작물학회지
• /
• 제28권4호
• /
• pp.391-418
• /
• 1983

질소질 비료로서 황산암모니아와 요소를 시용하는 경우 수도의 생육과 양분흡수에 미치는 영향을 검토하기 위하여 수원 26004와 진흥을 공시하여 묘대의 종류를 달리한 시험과 폿트에서 황산암모니아 및 요소의 시용 비율을 달리하고, 황산나트륨을 첨가한 시험, 그리고 양 비종을 각각 장기간 연용해온 논에서 시험을 수행한 바 그 결과를 요약하면 다음과 같다. 황산암모니아와 요소의 시용에 따른 수도묘의 생육 및 양분 흡수에 관한 시험에서는 1. 초장 및 묘의 건물중은 황산암모니아의 시용이 요소 시용보다 크고 특히 보온 밭 못자리에서 그 효과가 컸다. 2. 황산암모니아의 시용은 묘의 엽록소 함량을 증대시켰는데 수원 26004가 진흥보다 반응이 더 컸다. 3. 주요 무기성분의 흡수에 미치는 영향은 양 품종 모두 황산암모니아구가 요소구보다 크고 모대에 따라서는 보온 밭 못자리가 보온절충못자리보다 크며 특히 질소와 가리의 흡수를 증대시켰다. 4. 식물체의 황과 주요 무기성분과의 상관관계는 대부분 정의 상관이었으며 수원 26004가 진흥보다 그 관계가 더 뚜렷하였다. 황산암모니아 및 요소의 시용비율, 그리고 황산나트륨을 첨가한 풋트시험에서는 1. 수도의 간발, 수수, 엽중 및 정조 수량은 황산암모니아의 시용비율이 높아질수록 증대하였으며 황산나트륨의 첨가구는 저하하였다. 2. 출수전후기의 엽면적, 엽록소 함량 및 건물중은 황산암모니아의 시용비율이 높아질수록 증대하였으며 황산나트륨의 첨가는 엽록소 함량만을 증대시켰다. 3. 황산암모니아의 시용비율이 높아질수록 질소 및 칼리의 함량은 증가하였고 칼슘 함량은 감소하였는데 황산나트륨의 첨가시용도 같은 경향이었다. 3. 황산암모니아의 시용비율이 높아질수록, 그리고 황산나트륨의 첨가시용으로 출수기 지엽의 광합성 용력이 증대되었으며 수원 26004가 진흥보다 그 반응이 더 뚜렷하였다. 5. 염록소 함량 및 건물중과 엽신의 황의 함량과는 정의 상관을 보였으며 수원 26004가 진흥보다 더 큰 상관을 보였다. 황산암모니아와 요소를 각각 연용해온 논에서의 시험은 1. 엽록소 함량 및 건물중은 황산암모니아 시용구에서 더 컸으며 수확기 볏짚중의 질소 및 주요 무기성분의 함량은 황산암모니아구가 커서 양분의 잠재능력이 요소구보다 컸다. 2. 황산암모니아의 시용은 수수 및 등숙율을 높히는 경향이었고 통계적인 유의차는 없었으나 수량이 증대되었다.

• 한국환경과학회지
• /
• 제28권2호
• /
• pp.287-290
• /
• 2019

This study investigates the changes in ammonia fluxes, pH and total nitrogen of liquid ferrous sulfate-treated litter over 5 weeks. A total of 200 broiler chicks (Arbor Acres, 1 d old) was separated into two treatment groups (0 g and 100 g liquid ferrous sulfate/kg litter) with four replications of 25 birds in each group. Liquid ferrous sulfate was sprayed on the litter by using a small sprayer. There was no difference (p>0.05) in the ammonia fluxes observed between the control and liquid ferrous sulfate treatment groups at 0, 1, and 5 weeks, except for 2, 3 and 4 weeks. At 5 weeks, the litter pH and total nitrogen content did not show any difference (p>0.05) between the control and liquid ferrous sulfate treatment groups. In conclusion, the use of liquid ferrous sulfate is not a suitable for use in poultry litter to reduce ammonia and pH or improve the total nitrogen content.

• 한국대기환경학회지
• /
• 제20권6호
• /
• pp.803-810
• /
• 2004

Water contents in fine particles at Seoul and Gosan are estimated by using a gas/particle equilibrium model, SCAPE (Simulating Composition of Atmospheric Particles at Equilibrium). Also, sensitivity of particulate inorganic ionic concentrations on the total ionic species is estimated. Water content at Gosan is more sensitive to ambient relative humidity (RH) than Seoul. At both sites water content is most sensitive to sulfate concentration among sulfate, nitrate, and ammonium. Solid salts levels and compositions are also studied.