• Journal of Environmental Science International
• /
• v.6 no.2
• /
• pp.113-124
• /
• 1997

The basic mechanism of the granular sludge formation which is the most important factor in the start-up and stable operators is not confirmed yet. In this study, the effect of granular sludge formation was investigated with the different substrate concentrations and the various ratios of substrate supply/deficiency. The granular sludge formation in the UASB reactor was closely related to the substrate concentrations and the ratio of substrate supply/deficlency The granular sludge formation was not accelerated at low substrate concentration. It was convinced that granular sludge formation was accelerated when the substrate supply with high concentration was stopped at UASB reactor. From this experiment, it was estimated that granular sludge was formed by the combination of hydrogen utilizing bacteria that form hydrogen condition and acid forming bacteria at substrate deficit condition by mutual symbiosis. Though the removal efficiency of organic matter was decreased as the influent substrate concentration was Increased, the higher the influent substrate the better the granular sludge formation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.458-458
• /
• 2012

Fuel Cell is used stacking metal or polymer substrate. This hydro property of substrate surface is very important. Usually, surface property is hydrophilic. The surface oxidation of SUS is investigated through plasma treatments with an atmospheric-pressure dielectric barrier discharge (DBD) for increasing hydrophilic property. The plasma process makes an experiment under various operating conditions of the DBD, which operating conditions are treatment time, plasma gas mixture ratio, the plasma source supply frequency. Two kinds of SUS substrate, SUS-304 and SUS 316L, were used. Discharge frequency has a crucial impact on equipment performance and gas treatment. After the plasma treatment of a SUS plate, highly improved wettability was noted. But, when high oxygen supply, the substrate damaged seriously.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.703-706
• /
• 1998

This paper presents an efficient substrate-bias generator(SBG)for low-power, high-density DRAM's The proposed SBG can supply stable voltage with switching the supply voltage of driving circuit, and it can substitude the small capacitance for the large capacitance. The charge pumping circuit of the SBG suffere no VT loss and is to be applicable to low-voltage DRAM's. Also it can reduce the power consumption to make VBB because of it's high pumping efficiency. Using biasing voltage with positive temperature coefficient, VBB level detecting circuit can detect constant value of VBB against temperature variation. VBB level during VBB maintaining period varies 0.19% and the power dissipation during this period is 0.16mw. Charge pumping circuit can make VBB level up to -1.47V using VCC-1.5V, and do charge pumping operation one and half faster than the conventional ones. The temperature dependency of the VBB level detecting circuit is 0.34%. Therefore the proposed SBG is expected to supply a stable VBB with less power consumption when it is used in low power DRAM's.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.54-57
• /
• 2002

In this study, a new programming method, to minimize the generation of Si-SiO$_2$ interface traps of scaled SONOS flash memory as a function of number of program/erase cycles has been proposed. In the proposed programming method, power supply voltage is applied to the gate, forward biased program voltage is applied to the source and the drain, while the substrate is left open, so that the program is achieved by Modified Fowler-Nordheim (MFN) tunneling of electron through the tunnel oxide over source and drain region. For the channel erase, erase voltage is applied to the gate, power supply voltage is applied to the substrate, and the source and drain are open. A single power supply operation of 3 V and a high endurance of 1${\times}$10$\^$6/ prograss/erase cycles can be realized by the proposed programming method. The asymmetric mode in which the program voltage is higher than the erase voltage, is more efficient than symmetric mode in order to minimize the degradation characteristics of scaled SONOS devices because electrical stress applied to the Si-SiO$_2$ interface is reduced by short programming time.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.40-47
• /
• 2002

Because UV wavelength lights can activate photocatalysts, plasma is used as a light source of a photocatalytic reactor. Even though plasma has good intensity for photo reaction, substrate of catalyst coating was limited by the geometry of plasma generator. Usually bead type substrate was used for a pack bed type reactor. Honeycomb monolith type substrate was used with UV lamps instead plasma, due to the light penetration the honeycomb monolith length was too short to show good activity In this study a photocatalytic reactor, which is using a honeycomb monolith substrate, was investigated with plasma as an activation light source. As a parametric study the effects of 1311owing factors on plasma generation and power consumption are examined; supply voltage, substrate length, environment condition, catalyst loading and ratio. Using the test results, the practicability test was done with simulated synthetic gases representing bad smells and automotive exhaust gases.

• Proceedings of the Korea Society of Information Technology Applications Conference
• /
• 2005.11a
• /
• pp.99-102
• /
• 2005

In the paper, a proposed VCO based on bondwire inductances and nMOS varactors was implemented in a standard $0.25\;{\mu}m$ CMOS process. Using the new drain current model and a propagation delay time model equations, the operation speed of CMOS gate will predict the dependence on the load capacitance and the depth of oxide, threshold voltage, the supply voltage, the channel length. This paper describes the result of simulation which calculated a gate propagation delay time by using new drain current model and a propagation delay time model. At the result, When the reverse bias voltage on the substrate changes from 0 voltage to 3 voltage, the propagation delay time is appeared the delay from 0.8 nsec to 1 nsec. When the reverse voltage is biased on the substrate, for reducing the speed delay time, a supply voltage has to reduce. The $g_m$ value of MOSFET is calculated by using new drain current model.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.1 s.343
• /
• pp.1-6
• /
• 2006

This paper proposes substrate-bias voltage generator to reduce leakage power consumption of digital logic circuits operating at supply voltage of 0.5V. Proposed substrate-bias voltage generator is composed of VSS and VBB generator. The former circuit produces negative voltage and supplies its output voltage for VBB generator. As a result VBB generator develops much lower negative voltage than that of conventional one. Proposed circuit is fabricated using 0.18um 1Poly-6Metal CMOS process and measurement result demonstrated stable operation with substrate-bias voltage of -0.95V.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.1
• /
• pp.5-10
• /
• 2003

In this study, a new programming method to minimize the generation of Si-SiO$_2$interface traps of SONOS nonvolatile memory device as a function of number of porgram/erase cycles was proposed. In the proposed programming method, power supply voltage is applied to the gate. forward biased program voltage is applied to the source and the drain, while the substrate is left open, so that the program is achieved by Modified Fowler-Nordheim(MFN) tunneling of electron through the tunnel oxide over source and drain region. For the channel erase, erase voltage is applied to the gate, power supply voltage is applied to the substrate, and the source and dram are left open. Also, the asymmetric mode in which the program voltage is higher than the erase voltage, is more efficient than symmetric mode in order to minimize the degradation characteristics or SONOS devices because electrical stress applied to the Si-SiO$_2$interface is reduced due to short program time.

• Journal of Environmental Science International
• /
• v.30 no.8
• /
• pp.605-612
• /
• 2021

Supply electrical conductivity (EC) concentration of the nutrition solution is an important factor in the absorption of nutrients by plants and the management of the root zone, as it can control the vegetative/reproductive growth of a plant. Paprika usually undergoes its reproductive and vegetative growth simultaneously. Therefore, ensuring proper growth of the plant leads to increased yield of paprika. In this study, growth characteristics of paprika were examined according to the EC concentration of a coir and a rockwool substrate. The supply EC was 1.0, 2.0, and 4.0 mS·cm^-1 applied at the initial stages of the growth using the rockwool (commonly used by paprika farmers) and the coir substrate with a chip and dust ratio of 50:50 and 70:30. For up to 16 weeks of paprika growth, EC concentrations of 1.0 and 2.0 mS·cm^-1 were found to have a greater effect on the growth than EC at 4.0 mS·cm^-1. The normality (marketable) rate of fruit, the soluble solid content, and paprika growth showed that the coir was generally better than the rockwool regardless of the supply EC concentration. The values of the yield per plant at an EC concentration of 4.0 mS·cm^-1 was mostly similar at 1.6 kg (coir 50:50), 1.5 kg (coir 70:30) and 1.5 kg (rockwool), but the yield of the rockwool was 88%, which was lower than 98% and 94% yield of the coir substrate. Therefore, this concludes that coir substrate is more effective than rockwool at improving paprika productivity. The results also suggest that the use of coir substrate for paprika has many benefits in terms of reducing production costs and preventing environmental destruction during post-processing.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.6 no.1
• /
• pp.42-50
• /
• 2001

The activity of immobilized cell-support particle aggregates is influenced by physical and biochemical elements, mass transfer, and physiology. Accordingly, the mathematical model discussed in this study is capable of predicting the steady state and transient concentration profiles of the cell mass and substrate, plus the effects of the substrate and product inhibition in an immobilized cell-support aggregate. The overall mathematical model is comprised of material balance equations for the cell mass, major carbon source, dissolved oxygen, and non-biomass products in a bulk suspension along with a single particle model. A smaller bead size and higher substrate concentration at the surface of the particle, resulted in a higher supply of the substrate into the aggregate and consequently a higher biocatalyst activity.