• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.2
• /
• pp.252-257
• /
• 2011

Magnesium thin films for marine engine parts such as the engine block and the cylinder head cover etc. were prepared on the magnesium alloy(AZ91D) substrate by Thermo-electron activated Ion-plating method. The influence of gas pressure and substrate bias voltages on the crystal orientation and morphology of the films was investigated with X-ray diffraction and field emission scanning electron microscope(FE-SEM), respectively. Moreover, the effect of crystal orientation and morphology of the magnesium films on the its hardness property was investigated as well. From the results, the hardness of the films was increased in Ar gas pressure due to the grain boundary strengthening and occlusion effects.

• Applied Science and Convergence Technology
• /
• v.26 no.1
• /
• pp.11-15
• /
• 2017

To improve the adhesion of Mo thin film as a back contact material, a DC magnetron sputtering system was used to deposit in the form of a bi-layer on soda-lime glass. Films with low resistivity and good adhesion were obtained from this deposition, even though the two qualities were found be hard to obtain at the same time. The best Mo bi-layer showed a resistivity of $8.13{\times}10^{-4}{\Omega}{\cdot}cm$ at $500^{\circ}C$ and $3.0{\times}10^{-3}\;Torr$. The XRD measurements showed that the crystallites of the films were mainly oriented in the (110) direction, the FE-SEM images revealed that the resistivity of the Mo films decreased with increasing substrate temperature, which temperature reduction is accompanied by an increase of the grain size. These experimental results were analyzed using the Fuchs-Sondheimer theory. Our Mo bi-layer film with better crystallinity and lower resistivity can be suitably used as a back-contact layer for CIGS solar cells.

• KSBB Journal
• /
• v.19 no.1
• /
• pp.38-41
• /
• 2004

Enantioselective hydrolysis for the producing chiral epichlorohydrin from its racemic substrate was investigated using epoxide hydrolase activity of Rhodosporidium toruloides SJ-4. The effects of reaction parameters including pH, temperature, initial substrate concentration on initial hydrolysis rate and enantioselectivity were analyzed and optimized. The addition of detergent, Tween 20, enhanced the hydrolysis rate and enantioselectivity. Chiral (R)-epichlorohydrin with high optical purity (＞99% ee) and yield of 25% (theoretically 50% maximum yield) was obtained from its racemate of 20 mM.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.452-455
• /
• 2003

[ $ZrO_2$ ] dielectric layers were grown on the p-type Si (100) substrate by metalorganic molecular beam epitaxy(MOMBE). Zrconium t-butoxide, $Zr(O{\cdot}t-C_4H_9)_4$ was used as a Zr precursor and Argon gas was used as a carrier gas. The thickness of the layers was measured by scanning electron microscopy (SEM) and the properties of the $ZrO_2$ layers were evaluated by X-ray diffraction, high frequency capacitance-voltage measurement. and HF C-V measurements have shown that $ZrO_2$ layer grown by MOMBE has a high dielectric constant (k=18-19). The growth rate is affected by various process variables such as substrate temperature, bubbler temperature, Ar, and $O_2$ gas flows.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.1
• /
• pp.66-74
• /
• 2000

The structural and electrical characteristics of SBT thin films, fabricated on Pt/Ti/SiO\ulcorner/Si substrates by a pulsed laser deposition(PLD), were investigated to develop ferroelectric thin films for capacitor lay-ers of FRAM. EFfects of target composition on the characteristics of SBT thin films were examined. Target were prepared by mixed oxide method, and composition of Sr/Bi/Ta on SBT was changed to 1/2/2, 1/2.4/2, 1/2.8/2, 0.8/2/2 and 1.2/2/2. SBt thin films were fabricated, as a function of substrate temperature and oxygen pressure, by PLD. The optimized ocndition, to fabricate high quality SBT thin films, was 700 $^{\circ}C$ of substrate temperature, 200 mTorr of oxygen pressure, and 2 J/$\textrm{cm}^2$ of laser energy density. Maximum remnant value(2Pr) of 9.0 $\mu$C/$\textrm{cm}^2$, coercive field value(Ec) of 50 kV/cm, dielectric constant value of 166, and leakage current densities of <10\ulcorner A/$\textrm{cm}^2$ were observed for the films with 1/2/2 composition, which was prepared at the above PLD condition.

• Journal of Surface Science and Engineering
• /
• v.24 no.1
• /
• pp.1-17
• /
• 1991

Understanding of the detailed reaction mechanisms during MOVPE and ALE is essential to further improve the properties of the grown crystals and the controllability of the growth parameters. The unified models for the detailed reaction paths are not available at this stage. The study, however, has been advanced to the extent that consensus on some of the reaction paths can be drawn from the scattered data. Metalakyls such as TMGa and TMIn seem to nearly fully decompose in the gas phase through homogeneous reaction at the typical MOVPE growth temperature. Hydrides such as AsH3 and PH3, on the contrary. seem to decompose heterogeneously onthe substrate surfaces as well as homogeneously in the gas phase. However, at lower temperatures, where ALE crystals are typically grown, the growth process is strongly dependent on the surface reactions. It seems that steric hindrance effects which the radicals reaching the substrate exhibit on the surface the growth rate a function of the metalalkyle supply durations. In addition, dydrogens released from hydrides seem to play an essential role in removing carbons leberated from the metalalkyls. High growth temperatures also seem to be effective in desorbing carbons from surface. The understanding of the reaction mechanisms was possible though diverse appraaches utilizing many ex-situ and in-situ diagnostic techniques and genuine experimental designs. It is the purpose of this paper to review and discuss many of these efforts and to draw some possible conclusions from them.

• Journal of Surface Science and Engineering
• /
• v.24 no.1
• /
• pp.1.1-1.1
• /
• 1991

Understanding of the detailed reaction mechanisms during MOVPE and ALE is essential to further improve the properties of the grown crystals and the controllability of the growth parameters. The unified models for the detailed reaction paths are not available at this stage. The study, however, has been advanced to the extent that consensus on some of the reaction paths can be drawn from the scattered data. Metalakyls such as TMGa and TMIn seem to nearly fully decompose in the gas phase through homogeneous reaction at the typical MOVPE growth temperature. Hydrides such as AsH3 and PH3, on the contrary. seem to decompose heterogeneously onthe substrate surfaces as well as homogeneously in the gas phase. However, at lower temperatures, where ALE crystals are typically grown, the growth process is strongly dependent on the surface reactions. It seems that steric hindrance effects which the radicals reaching the substrate exhibit on the surface the growth rate a function of the metalalkyle supply durations. In addition, dydrogens released from hydrides seem to play an essential role in removing carbons leberated from the metalalkyls. High growth temperatures also seem to be effective in desorbing carbons from surface. The understanding of the reaction mechanisms was possible though diverse appraaches utilizing many ex-situ and in-situ diagnostic techniques and genuine experimental designs. It is the purpose of this paper to review and discuss many of these efforts and to draw some possible conclusions from them.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.3_1spc
• /
• pp.544-550
• /
• 2013

A grooved surface with anisotropic wettability was fabricated on a silicon substrate using photolithography, reactive ion etching, and a KOH etching process. The contact angles (CAs) of water droplets were measured and compared with the theoretical values in the Cassie state and Wenzel state. The experimental results showed that the contact area between a water droplet and a solid surface was important to determine the wettability of the water. The specimens with native oxide layers presented CAs ranging from $71.6^{\circ}$ to $86.4^{\circ}$. The droplets on the specimens with a native oxide layer could be in the Cassie state because they had relatively smooth surfaces. However, the CAs of the specimens with thick oxide layers ranged from $33.4^{\circ}$ to $59.1^{\circ}$. This indicated that the surface roughness for a specimen with a relatively thick oxide layer was higher, and the water droplet was in the Wenzel state. From the CA measurement results, it was observed that the wetting on the grooved surface was anisotropic for all of the specimens.

• Korean Journal of Organic Agriculture
• /
• v.6 no.1
• /
• pp.127-132
• /
• 1997

This experiment was carried out to examine the effect of various functional materials such as bioceramic podwers, crushed shells and elvanites supplemented to the each substrate on the seedlings growth of rices. The rice seedlings were grown in pots filled with substrates supplemented with bioceramic podwers, crushed shells and elvanites. The growth of rice seedlings in terms of plant height, stem diameter, root length and leaf width, plant fresh and dry weight was promoted by adding the bioceramic powders (2 to 3g/kg), crushed shells (10g/kg) or elvanites (20 to 40g/kg). Plant height was also promoted by the adding of bioceramic powder from 16 days after treatment, whereas crushed shells and elvanites from 10 days after treatment. Especially, root growth was greatly influenced by bioceramic powder, whereas the shoot growth(leaves and stem) was stimulated by the crushed shells and elvanites supplemented into each substrate. In the field, plant growth in terms of plant height, leaf length and leaf width were also influenced by crushed shells and elvanites at 74 days after treatment. The growth of rices in terms of tiller number, spikelets, panicles and spikelets/panicle was incresed by adding the crushed shells and elvanites from 100 to 200g per m2.

• Applied Chemistry for Engineering
• /
• v.25 no.2
• /
• pp.152-156
• /
• 2014

Isoquercitrin (IQ), quercetin monoglycoside, is classified as a polyphenol, and a minute quantity of IQ is known to be present in several plants. Recently, it was reported that IQ can be prepared by the partial enzymatic hydrolysis of quercetin diglycoside (rutin, RU). In this paper, the effects of enzyme types, enzyme amounts, and substrate concentrations on the reactivity were investigated using a series of $Pecinex^{TM}$ multi-enzymes. The reaction, when a 8 ml of Ultra Clear to 1 g of RU was applied with the substrate concentration of 1% at $50^{\circ}C$, was found to be optimum, based on the reaction rate and the selectivity to IQ.