• Tribology and Lubricants
• /
• 제36권3호
• /
• pp.153-160
• /
• 2020

In this paper, we present a hydrostatic bearing design and rotordynamic analysis of a pump-and-drive turbine module for a 250-kW supercritical CO₂ cycle application. The pump-and-drive turbine module consists of the pump and turbine wheel, assembled to a shaft supported by two hydrostatic radial and thrust bearings. The rated speed is 21,000 rpm and the rated power is 143 kW. For the bearing operation, we use high-pressure CO₂ as the lubricant, which is supplied to the bearing through the orifice restrictor. We calculate the bearing stiffness and flow rate for various orifice diameters, and then select the diameter that provides the maximum bearing stiffness. We also conduct a rotordynamic analysis based on the design parameters of the pump-and-drive turbine module. The predicted Campbell diagram shows that there is no critical speed below the rated speed, owing to the high stiffness of the bearings. Furthermore, the predicted damping ratio indicates that there is no unstable mode. We conduct the operating tests for the pump and drive turbine modules within the supercritical CO₂ cycle test loop. The pressurized CO₂, at a temperature of 136℃, is supplied to the turbine and we monitor the shaft vibration during the test. The test results show that there is no critical speed below the rated speed, and the shaft vibration is controlled to below 3 ㎛.

• Steel and Composite Structures
• /
• 제51권1호
• /
• pp.25-41
• /
• 2024

The measurement of pile bearing capacity is crucial for the design of pile foundations, where in-situ tests could be costly and time needed. The primary objective of this research was to investigate the potential use of fuzzy-based techniques to anticipate the maximum weight that concrete driven piles might bear. Despite the existence of several suggested designs, there is a scarcity of specialized studies on the exploration of adaptive neuro-fuzzy inference systems (ANFIS) for the estimation of pile bearing capacity. This paper presents the introduction and validation of a novel technique that integrates the fire hawk optimizer (FHO) and equilibrium optimizer (EO) with the ANFIS, referred to as ANFIS_FHO and ANFIS_EO, respectively. A comprehensive compilation of 472 static load test results for driven piles was located within the database. The recommended framework was built, validated, and tested using the training set (70%), validation set (15%), and testing set (15%) of the dataset, accordingly. Moreover, the sensitivity analysis is performed in order to determine the impact of each input on the output. The results show that ANFIS_FHO and ANFIS_EO both have amazing potential for precisely calculating pile bearing capacity. The R² values obtained for ANFIS_FHO were 0.9817, 0.9753, and 0.9823 for the training, validating, and testing phases. The findings of the examination of uncertainty showed that the ANFIS_FHO system had less uncertainty than the ANFIS_EO model. The research found that the ANFIS_FHO model provides a more satisfactory estimation of the bearing capacity of concrete driven piles when considering various performance evaluations and comparing it with existing literature.

• Geomechanics and Engineering
• /
• 제29권5호
• /
• pp.487-496
• /
• 2022

Most of the pile's vertical static load tests in construction sites are the proof load tests, which is difficult to accurately estimate the ultimate bearing capacity and analyze the reliability of piles. Therefore, a reliability analysis method based on the proof load-settlement (Q-s) data is proposed in this study. In this proposed method, a simple ultimate limit state function based on the hyperbolic model is established, where the random variables of reliability analysis include the model factor of the ultimate bearing capacity and the fitting parameters of the hyperbolic model. The model factor M = R_uR / R_uP is calculated based on the available destructive Q-s data, where the real value of the ultimate bearing capacity (R_uR) is obtained by the complete destructive Q-s data; the predicted value of the ultimate bearing capacity (R_uP) is obtained by the proof Q-s data, a part of the available destructive Q-s data, that before the predetermined load determined by the pile test report. The results demonstrate that the proposed method can easy and effectively perform the reliability analysis based on the proof Q-s data.

• Nuclear Engineering and Technology
• /
• 제54권4호
• /
• pp.1175-1184
• /
• 2022

The pore structure of uranium-bearing sandstone is one of the critical factors that affect the uranium leaching performance. In this article, uranium-bearing sandstone from the Yili Basin, Xinjiang, China, was taken as the research object. The fractal characteristics of the pore structure of the uranium-bearing sandstone were studied using mercury intrusion experiments and fractal theory, and the fractal dimension of the uranium-bearing sandstone was calculated. In addition, the effect of the fractal characteristics of the pore structure of the uranium-bearing sandstone on the uranium leaching kinetics was studied. Then, the kinetics was analyzed using a shrinking nuclear model, and it was determined that the rate of uranium leaching is mainly controlled by the diffusion reaction, and the dissolution rate constant (K) is linearly related to the pore specific surface fractal dimension (D_S) and the pore volume fractal dimension (D_V). Eventually, fractal kinetic models for predicting the in-situ leaching kinetics were established using the unreacted shrinking core model, and the linear relationship between the fractal dimension of the sample's pore structure and the dissolution rate during the leaching was fitted.

• Earthquakes and Structures
• /
• 제22권6호
• /
• pp.597-608
• /
• 2022

One of the most important parameters affecting nonlinearsoil-structure interaction, especially rocking foundation, is the vertical factor of safety (F.S_v). In this research, the effect of F.S_v on the behavior of rocking foundations was experimentally investigated. A set of slow, cyclic, horizontal loading tests was conducted on elastic SDOF structures with different shallow foundations. Vertical bearing capacity tests also were conducted to determine the F.S_v more precisely. Furthermore, 10% silt was mixed with the dry sand at a 5% moisture content to reach the minimum apparent cohesion. The results of the vertical bearing capacity tests showed that the bearing capacity coefficients (N_c and N_γ) were influenced by the scaling effect. The results of horizontal cyclic loading tests showed that the trend of increase in capacity was substantially related to the source of nonlinearity and it varied by changing F.S_v. Stiffness degradation was found to occur in the final cycles of loading. The results indicated that the moment capacity and damping ratio of the system in models with lower F.S_v values depended on soil specifications such cohesiveness or non-cohesiveness and were not just a function of F.S_v.

• Geomechanics and Engineering
• /
• 제31권4호
• /
• pp.385-393
• /
• 2022

Previous studies postulated insignificant capillary rise (h_c) effect above the water table (H_w) for unsaturated soils. In addition, these studies utilised dry unit weight above H_w. This paper, therefore, addresses the effect of these postulations on strength where the influence of h_c using a modified upper bound approach, Discontinuity Layout Optimization (UNSAT-DLO) for a simulated soil was predicted. Two different parametric studies to model passive earth pressure and bearing capacity problems are carried out to provide an insight into the effect of capillary rise on strength. Significant increase in strength, owing to unsaturated conditions, was obtained where the maximum increase was when suction slightly less or greater than the air entry suction. On the other hand, the results showed a negative effect of h_c. For example, up to 8.24% decrease in passive thrust (P_p) was obtained at H_w=0 m when h_c rose 1 m from 0 m. To put this into perspective, this was equivalent to a decrease of about 2° in 𝜙 at H_w=0 m and h_c =0 m in order to obtain the same result at h_c =1 m. For the bearing capacity problem, the effect was seen to be higher, up to 18.4% decrease in N_𝛾 was obtained when h_c rose from 0 m to 2.5 m at H_w =0 m. In addition, the results revealed a negative influence of assigning dry unit weight above H_w or h_c.. However, considerable increase in strength was obtained when unsaturated unit weight above h_c was assigned.

• 한국산림과학회지
• /
• 제107권2호
• /
• pp.166-173
• /
• 2018

본 연구는 목재운송 효율을 도모하기 위하여 목재운송차량이 대형화 되어감에 따라 대형 목재운송차량의 원활한 임도 통행을 위한 노면지지력 확보할 수 있는 노반 시설기준을 마련하고자 실시하였다. 산림기술경영연구소 관내 연약지반 임도 노면에 대하여 토목섬유를 활용하여 적정 골재배합비로 조성한 노반의 두께별 노면지지력 강화효과를 분석한 결과는 다음과 같다. 토목섬유를 활용하여 상굴식으로 노반을 0.2 m 이상 포설한 시험구간은 노면지지력이 CBR 15% 이상으로 양호한 것으로 나타났다. 그러나 토목섬유 종류별 노면지지력 보강효과는 큰 차이가 없었고, 상치식으로 조성한 구간의 경우 노면지지력이 미흡한 것으로 나타났다. 따라서 연약지반 구간에서는 상굴식으로 터파기 한 후 토목섬유를 부설하고, 노반층 두께를 0.2 m 이상 조성한 후 표층을 포설하여야 대형 목재운송차량의 원활한 통행에 필요한 노면지지력 확보가 가능할 것으로 판단된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.810-816
• /
• 2001

In this paper, we theoretically analyzed the NRRO(the non-repeatable run-out) of a ball bearing with geometric imperfection. The quasi-static and dynamic analysis of a ball bearing was performed to calculate the displacement of shaft center caused by the form errors while the shaft is rotating. From consideration of the generating mechanism of NRRO, it is found that the waviness of one ball generates vibrations with nf$\sub$b/${\pm}$f$\sub$c/(where n is odd) components. Also it is confirmed that the outer race waviness of the order n = jZ${\pm}$1 generates vibration with jZf$\sub$c/ components. The form errors of ball bearing elements were precisely measured and NRRO of a ball bearing was calculated using the measured data. It is concluded that the ball bearings must has large ball number and small ball diameter to obtain low NRRO.

• 한국지반공학회논문집
• /
• 제37권6호
• /
• pp.5-20
• /
• 2021

본 연구에서는 풍화암에 근입된 강관 매입말뚝의 지지력 공식 제안을 위하여 정재하시험 20본과 확인지반조사를 수행하였다. 기존 공식의 표준관입저항치를 50으로 제한하는 문제를 극복하기 위해 지반 현장 상태를 고려할 수 있도록 확장된 표준관입저항치를 기반으로 새로운 지지력 공식을 제안하였다. 재하시험 데이터는 통계적 처리를 수행하였다. 이때, 통계적 처리를 수행하여 얻어진 지지력과 기존공식을 이용한 지지력을 비교한 결과 기존공식이 지지력을 보수적으로 평가하고 있는 것으로 나타났다. 제안된 공식은 기존공식에 비해 지지력은 선단 15%, 주면 20% 더 높게 (q_t=230P_driven(kN/m²), f_max=3.0N_s^E(kN/m²)) 평가되는 것으로 확인되었다. 제안식은 여타 현장에 대해 재하시험 결과와 검증을 수행하였으며, 검증 과정에서 제안된 공식이 기존 공식보다 정확히 평가하는 것으로 나타났다.

• Computers and Concrete
• /
• 제33권5호
• /
• pp.573-594
• /
• 2024

This article presents a research study, with both laboratory and field tests, of a deep foundation in a markedly anisotropic medium. Particularly it has focused on the evaluation of the behavior of a pile, one meter in diameter, embedded in a rocky environment with difficult conditions, in the Flysch of the Spanish city of San Sebastián. To carry out the research, the site of a bridge over the Urumea River was chosen, which was supported by pre-excavated reinforced concrete piles. 4 borings were carried out, by the rotation and washing method, with continuous sampling and combined with flexible dilatometer tests. In the field, an Osterberg load test (O-cell) was performed, while in the laboratory, determinations of natural moisture, natural unit weight, uniaxial compressive strength (UCS), point load strength (PLS), compressive wave propagation velocity (V_c) and also triaxial and direct shear tests were carried out. The research results indicate the following: a) the empirical functions that correlate the UCS with the PLS are not always linear; b) for the studied Flysch it is possible to obtain empirical functions that correlate the UCS with the PLS and with the V_c; c) the bearing capacity of the studied Flysch is much greater than if it is evaluated by different load capacity theories; d) it is possible to propose an empirical function that allows evaluating the mobilized shear strength (τ_m), as a function of the UCS and the displacement relative of the pile (δ_r).