• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.865-870
• /
• 2001

This paper propose a new seismic detail for ductility enhancement by interlocking spiral reinforcement in the potential yield regions of a wall. Through the theoretical consideration and experiment program, confinement with interlocking spirals lead the structural walls to ductile behavior. All specimens show stable hysteretic behavior and good energy dissipation capacity. Also the increase of shear strength mainly induces a flexural failure mode. As interlocking spiral are used in lapped splice region, they increase the bond strength and prevent a early tensile failure caused by the loss of bond stresses. Consequently, the confinement with interlocking spirals may result in a lower value of force reductions factor, newly proposed detail will be provide more economical design.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.21 no.1
• /
• pp.21-29
• /
• 2017

Purpose of this study is to investigate structural behavior of the rectangular hollow column with various transverse reinforcement details. Experimental variables are diameter, arrangement details and lateral spacing of cross tie. A total of 66 column specimens have been prepared and tested under axial compressive load. Test results showed that behaviors of column specimens were different depending on the cross tie details. Specimens with cross tie wrapping longitudinal steel and transverse steel have greater strength and ductility than specimens with cross tie wrapping the longitudinal steel.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.2
• /
• pp.191-197
• /
• 2010

In spite of a large amount of previous research, detail study on modified mass in proportional damping system is not well understood. It is common to predict structural dynamic design parameters due to the change of mass, but to predict the amount of modified mass and the location where the mass is being modified are rarely found in previous literature. Such inverse problem required detail analytical study in order to understand structural modification in proportional damping system. This paper predicts the modified mass and the modified mass location in proportional damping system using sensitivity coefficients and iterative method. The sensitivity coefficients are obtained from the change of eigenvectors due to mass modification. This method is applied to a horizontal beam and three degree of freedoms system. To validate the predicted changing mass and its location, the obtained results are compared to the reanalysis result which shows good agreement.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1998.10a
• /
• pp.53-60
• /
• 1998

Efficiency of design process for large scale structures highly depends on the development of efficient structural analysis and structural response control algorithms because a successful design involves a number of structural analysis based on iterative structural response control process. In this paper, distributed structural analysis model on multiple personal computers connected by ethernet network is presented. To reduce communication cost required in the process of analysis, substructuring techniques are adopted to evenly distribute computational loads on each processor. With its applications on structural analysis of plane frame structures, performance of the proposed computational model are presented in detail.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.3
• /
• pp.319-329
• /
• 2001

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.265-268
• /
• 2008

With application of IT convergence technique in AEC industry, it is currently conducted the research on the virtual construction system. This paper aims at the pilot study on the structural design based on BIM used in collaboration environment. The work scope of structural design includes the structural analysis model, structural detail model and analytic model and we focuse the research on the interoperability among them. It is partly utilized the transfer module supplied by software developer and partly developed here the interface module through API. This paper shows the interoperability process to pilot test and indicates the problems occurred in interface.

• Journal of Korean Society of Steel Construction
• /
• v.25 no.5
• /
• pp.451-461
• /
• 2013

In steel bridges, there are several details that constrain the deformation such as buckling by external forces. Most of these details which are composed of the intersection members have scallops in order to exclude the weld defects inherently and to get the ease of fabrication and also to decrease the stress concentration. In this study, stress relief hole (SRH) near stress concentration zone with detail category D or under is proposed as a method to improve the resistance on the fatigue crack initiation to detail category C. And the effects of the appropriate size and location of SRH were examined and the applicability to improve the fatigue resistance of the floorbeam web and the rib wall at rib/floorbeam intersection in the orthotropic steel deck bridge was evaluated.

• Aerospace Engineering and Technology
• /
• v.8 no.1
• /
• pp.117-131
• /
• 2009

In this study, a detail design was conducted for KSLV-1 1st stage Rear Fuselage Upper Compartment assembly. A basic structural sizing was done by the aircraft fuselage sizing in-house program. The frame structural design and the interface check were conducted by the FE and the CAD program. The structural margin of safety was conformed by FE analysis for the normal section model and duct cut-out section models which are the weakest parts of the rear fuselage. The shear stress analysis was performed for a fastener design of the skin-stringer which is most affected by the shear stress induced by the shear load.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2010.05a
• /
• pp.29-31
• /
• 2010

This study investigated the typical standards of B kind of standard specification related to home and abroad forms design and compared them, and the results can be summarized as follows. In case of domestic standards, regulations on most forms design was described relatively in detail. and in case of CTEA among them, it included detailed contents of load conditions, lifting and subsidence. In case of abroad standards, the design regulations are only simply mentioned, not in detail, in ACI, CEB-FIP and BS, and JCI and JASS were similar to domestic KCI and KASS regulations. As to structural calculation in forms design regulations, most of domestic regulations included detailed matters on structural calculation, among them, CTEA shows the most detailed matters on it. On the other hand, it could be known that in case of abroad standards, most standards do not include matters on structural calculation except ACI, JCI and JASS.

• Journal of Fashion Business
• /
• v.23 no.3
• /
• pp.1-9
• /
• 2019

The purpose of this study was to develop questions for fashion design development, by applying 7 elements of the scamper to the fashion design elements, and to present a scamper checklist of fashion design elements, and item structures. In this study, the scope of research was limited to clothing design among various fashion products, and among various design development stages. Fashion design development focusing on design sketching, was limited to the research scope. The research method was based on an empirical study that derived scamper questions through FGI (Focus Group Interview), consisting of 5 fashion experts. Fashion design elements applied to development of scamper questions consisted of silhouettes, constructive lines, structural details, decorative details, patterns and textures of fabrics, and item structures, derived by applying these elements to the individual 7 elements of the scamper: substitute, combine, adjust, modify, put to other uses, eliminate, and reverse. Results of the study included 7 questions for substituting, 8 questions for combining, 6 questions for applying, 15 questions for modifying, 4 questions for putting to other uses, 4 questions for eliminating, and 7 questions for reversal. The scamper checklist for fashion design elements and item structures drew to 5 lists of silhouette variations, 7 lists of constructive line variations, 11 lists of structural detail variations, 10 lists of decorative detail variations, 11 lists of fabric variations, and 9 lists of structural modifications of items.