• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.1
• /
• pp.21-28
• /
• 2000

Although commercial PIV systems have been widely used for the non-intrusive velocity field measurement of fluid flows, they are still under development and have considerable room for improvement. In this study, a single-frame double-exposure PIV system using a high-resolution CCD camera was developed. A pulsed Nd:Yag laser and high-resolution CCD camera were synchronized by a home-made control circuit. In order to resolve the directional ambiguity problem encountered in the single-frame PIV technique, the second particle image was genuinely shifted in the CCD sensor array during the time interval dt. The velocity vector field was determined by calculating the displacement vector at each interrogation window using cross-correlation with 50% overlapping. In order to check the effect of spatial resolution of CCD camera on the accuracy of PIV velocity field measurement, the developed PIV system with three different resolution modes of the CCD camera (512 ${\times}$ 512, lK ${\times}$ IK, 2K ${\times}$ 2K) was applied to a turbulent flow which simulate the Zn plating process of a steel strip. The experimental model consists of a snout and a moving belt. Aluminum flakes about $1{\mu}m$ diameter were used as scattering particles for the liquid flow in the zinc pot and the gas flow above the zinc surface was seeded with atomized olive oil with an average diameter of 1-$3{\mu}m$. Velocity field measurements were carried out at the strip speed $V_s$=1.0 m/s. The 2K ${\times}$ 2K high-resolution PIV technique was significantly superior compared to the smaller pixel resolution PIV system. For the cases of 512 ${\times}$ 512 and 1K ${\times}$ 1K pixel resolution PIV system, it was difficult to get accurate flow structure of viscous flow near the wall and small vortex structure in the region of large velocity gradient.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.8
• /
• pp.39-47
• /
• 1999

This paper describes on-line retrainable RBF network in order to control the coiling temperature for a hot coil strip at Pohang Iron & Steel Company(POSCO). The proposed neural network can be used for improving conventional rule-based lookup table, which generates a heat transmission coefficient. To cope with time-varying characteristics of hot coil process, additional synaptic weights for on-line retraining purposes are introduced to hidden-to-output weights of conventional RBF network. Those weights are locally adjusted to newly incoming test data while preserving old information trained with off-line past data. Hence the effect of catastrophic interference can be greatly alleviated with the proposed network. In addition, rejection scheme is introduced for reliability concerns. From the experimental results applied to the actual process, it is noticed that overall control performance represents about 2.2% increase compared to the conventional one.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.5
• /
• pp.687-695
• /
• 2007

Statement of problem: The proper contact relation between adjacent teeth in each arch plays an important role in the stability and maintenance of the integrity of the dental arches. Proximal contact has been defined as the area of a tooth that is in close association, connection, or touch with an adjacent tooth in the same arch. Purpose: The aim of this study was to develop a digital device for measuring the proximal tooth contact tightness by pulling a thin stainless steel strip (2mm wide, 0.03mm thick) inserted between proximal tooth contact. Material and method: This device consists of measuring part, sensor part, motor part and body part. The stainless steel strip was connected to a stain gauge. The strain gauge was designed to convert the frictional force into a compressive force. This compressive force was detected as a electrical signal and the electrical signal was digitalized by a A/D converter. The digital signals were displayed by a micro-processor. The pulling speed was 8mm/s. Results: For testing reliability of the device in vivo, two healthy young adults (A, B) participated in this experiment. The tightness of proximal tooth contact between the second premolar and the first molar of mandible (subject A) and maxilla (subject B) was measured fifteen times for three days at rest. We double-checked the accuracy of the device with a Universal Testing Machine. Output signals from the Universal Testing Machine and the measuring device were compared. Regression analysis showed high linearity between these two signals. In vivo test, no significant differences were found between measurements. Conclusion: This device has shown to he capable of producing reliable and reproducible results in measuring proximal tooth contact. Therefore, it was considered that this device was appropriate to apply clinically.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.20 no.1
• /
• pp.59-67
• /
• 2002

Recently, much demand of vector data have increased rapidly such as a digital map instead of traditional a paper map and the raster data such as a high-resolution orthoimage have been used for many GIS application with the advent of industrial high-resolution satellites and development of aerial optical sensor technologies. Aerial photogrammetric technologies using an airship can offer cost-effective and high-resolution color images as well as real time images, different from conventional remote sensing measurements. Also, it can acquire images easily and its processing procedure is short and simple relatively. On the other hand, it has often been used for the production of a small-scale land use map not required high accuracy, monitoring of linear infrastructure features through mosaicking strip images and construction of GIS data. Through this study, the developed aerial photogrammetric system using the airship expects to be applied to not only producing of scale 1:5, 000 digital map but also verifying, editing, and updating the digital map which was need to be reproduced. Further more, providing the various type of video-images, it expects to use many other GIS applications such as facilities management, scenery management and construction of GIS data for Urban area.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.1
• /
• pp.45-50
• /
• 2009

By Laser Through-Silicon-Via process, debris and particles occur when you are forming. Therefore the research of TSV cleaning become important to remove those particles and debris. Both chemical cleaning method that uses a surfactant and physical cleaning method that uses a brush were studied with the via of $30{\mu}m$ diameter and $100{\mu}m$ depth on the 8 inch CMOS Image Sensor wafer. On the DI water and a surfactant in mixture ratio of 2:1, debris show $73{\mu}m^2$ per $0.054mm^2$. Cleaning is superior by lower mixture ratio of DI water and surfactant. In addition, It is less than 5% of debris distribution in the laser condition changed by Laser's frequency and its speed and cleaning had no effect. In the physical cleaning, there are no crack and damage when the system condition is set by $1000{\sim}3000rpm$ strip, $50{\sim}3000rpm$ rinsing, and $200{\sim}300rpm$ brushing Therefore, debris and particles can be removed by enforced chemical method and physical method.

• Journal of Sensor Science and Technology
• /
• v.20 no.5
• /
• pp.343-350
• /
• 2011

The compliance and stiffness of artery are closely related with disease of arteries. Pulse wave velocity(PWV) in the blood vessel is a basic and common parameter in the hemodynamics of blood pressure and blood flow wave traveling in arteries because the PWV is affected directly by the conditions of blood vessels. However, there is no standardized method to measure the PWV and it is difficult to measure. The conventional PWV measurement has being done by manual calculation of the pulse wave transmission time between coronary arterial proximal and distal points on a strip chart on which the pulse wave and ECG signal are recorded. In this study, a pressure sensor consisting of strain gauges is used to measure the blood pressure of arteries in invasive method and regular ECG electrodes are used to record the ECG signal. The R-peak point of ECG is extracted by using a reference level and time windowing technique and the ascending starting point of blood pressure is determined by using differentiation of the blood pressure signal and time windowing technique. The algorithm proposed in this study, which can measure PWV automatically, shows robust and good results in the extraction of feature points and calculation of PWV.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.2
• /
• pp.9-14
• /
• 2009

This study was conducted to develop a electronic circuit of primary color reaction for urine analyzer for measuring color response of urine strip. A primary color reaction system is equipped with the computer, electronic circuit, tray, detecting assembly and software. The determination of coefficient($R^2$) between reagent and color sensor were 0.9801(R), 0.9868(G) and 0.9837(B). To evaluate the system verification, we measured the primary color reaction of erythrocytes, Bilirubin, Urobilinogen, Ketones and Protein. We concluded that it is possible to use the developed the primary color reaction system for urine analyzer using u-health.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.6
• /
• pp.631-640
• /
• 2009

The highest priority of the cruise trip is the safety and comfort of its passengers. Though the cruise lines take every appropriate measure to ensure that their Passengers are safe and experience enjoyable vacations it is hard to fulfill all passenger's personnel requirement with limited number of crews. Generally, each passenger is issued an identification card which contains their digital photo and personal identification information on a magnetic strip that he or she must present when entering or leaving the ship. This technology allows the ship to know which Passengers and crew members are on board and which are not. However, this system has some limitations of functions and usage. To support each passenger as his or her personal liking, additional number of crews or some kind of new system is needed. In this paper, the crew support system based on sensor network using wireless and wired communication technologies was studied. To design the system, PLC(Power Line Communication) system and ZigBee based passenger location recognition, classification system has studied experimentally. By using this system, crews can serve passengers more closely and personally with less effort.

• Journal of Biosystems Engineering
• /
• v.36 no.2
• /
• pp.140-146
• /
• 2011

This study was performed to develop a rapid test kit for pathogenic Salmonella in various samples. The rapid detection kit has been fabricated based on nitrocellulose lateral-flow strip. Colloidal gold and biotin conjugated Salmonella antibodies were used as a tag and a receptor, respectively. Manually spotted Salmonella antibody and Neutravidin on nitrocellulose membrane were used as test and control lines, respectively. Feasibility of the rapid kit to detect Salmonella typhimurium in samples were evaluated. The intensity of the color of the test line started to increase with the samples in which higher concentration of the cells were contained. The sensitivity of the sensor was $10^6$ cfu/mL Salmonella spiked in PBS. Also, the rapid test kit could detect $10^6$ cfu/mL of Salmonella in chicken meat extract.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.100-108
• /
• 2004

In reverse engineering, data acquisition methodology can generally be categorized into contacting and non-contacting types. Recently, researches on hybrid or sensor fusion of the two types have been increasing. In addition, efficient construction of a geometric model from the measurement data is required, where considerable amount of user interaction to classify and localize regions of interest is inevitable. Our research focuses on the classification of each bounded region into a pre-defined feature shape fer a hybrid measuring scheme, where the overall procedures are described as fellows. Firstly, the physical model is digitized by a non-contacting laser scanner which rapidly provides cloud-of-points data. Secondly, the overall digitized data are approximated to a z-map model. Each bounding curve of a region of interest (featured area) can be 1.aced out based on our previous research. Then each confined area is systematically classified into one of the pre-defined feature types such as floor, wall, strip or volume, followed by a more accurate measuring step via a contacting probe. Assigned to each feature is a specific digitizing path topology which may reflect its own geometric character. The research can play an important role in minimizing user interaction at the stage of digitizing path planning.