• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.201-207
• /
• 1999

The automatic pinhole detection system is described. The goal of this project is to study the feasibility test of the new concept for hole detection. The developed method is able to detect almost 50$\mu\textrm{m}$ pinhole by evaluating the shining of the light as if there is pinhole in the strip. Moreover, it is possible to inspect up to the 200$\mu\textrm{m}$ inclined pinhole. The system cosists of three main functional parts: the source part of the light which is using the linear halogen lamp, the image gathering part which is using a line CCD and the image processing part. The light spot can be controlled and optimized corresponding to the situation of the strip. To eliminate back ground noise, the binary image processing method is adopted.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.7
• /
• pp.1597-1603
• /
• 1995

A prediction model on forward slip has been developed for presetting rolling speed of each finish mill stand in the continuous hot strip roduction. Those factors such as neutral point, friction coefficient, volume fractions undergoing width spread, shape of deformation zone at each side of entry and delivery of the rolls were taken into account. To reduce the speed unbalance between adjacent stands a refining method of adjusting friction coefficient has also been developed. On-line application of the model showed a good agreement in rolling speeds between the predictions and the actual measurements, and gave an outstanding improvement in the travelling stability of strip passing through the finishing mill train.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.04a
• /
• pp.73-76
• /
• 2009

Increase in tensile strength of steel is important for fuel efficiency and $CO_2$ reduction. But the higher the strip strength, the more defect could be generated in hot strip mill. This study focuses on line-type edge scab. One of the causes for the defect is initial edge cracks commonly observed on a slab but their correlation has not been verified yet. Thus, the objective of this report is to verify if the edge crack is exactly the seed for edge scab. For this, we conducted pilot hot rolling test with cracked slab and compared the development of cracks and edge scabs on hot-rolled strip.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.69.1-69
• /
• 2002

1. Introduction 2. STS Cold Rolling Process 3. Shape Control Method 4. On Line Test 5. Conclusions

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.4
• /
• pp.498-505
• /
• 1999

The ferrite device that has nonreciprocal characteristics has been used as various microwave components. In this paper, the spectral-domain method was used to analyze the characteristics of structure(strip line on multilayer structure with ferrite material) for which no paper has been published yet. It is assumed that an external dc magnetic field is applied perpendicular to the ground conductor. The propagation constant is calculated for each parameter and frequency. Also we considered convergence by increasing the number of basis functions and verified the numerical analysis results. From the results, we could confirm that as the thicknesses of YIG is increased, the cutoff region is widened and the propagation constant is decreased at the frequency of upper cutoff region. For a larger applied dc magnetic field, the frequency of cutoff region is found to be increased. Also the simulation results for strip line show that the cutoff region is widened and the propagation constant is larger than that of microstrip line.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.1
• /
• pp.15-22
• /
• 2018

In this paper, a microstrip-fed triple-band monopole antenna for WLAN/WiMAX applications was proposed. The proposed antenna is consist of two arc-shaped and one strip line structure, then get the three current path and then designed in order to get triple resonant characteristics. We carried out simulation about parameters. Taking account of coupling effect, Adjusted the length of the two arc-shaped and one strip line, we get the optimized parameters. The proposed antenna is fabricated on an FR-4 substrate, the dielectric constant is 4.4, and total size is $23.5mm(W1){\times}32.0mm(L1){\times}1.0mm(t)$, and its proposed antenna size is $21.0mm(W6){\times}31.0mm(L7)$. From the measured results, return loss of the proposed antenna satisfied return loss 927 MHz (1.844~2.771 GHz), 926 MHz (3.33~4.256 GHz), and 1,415 MHz (5.13~6.545 GHz). And measured results of gain and radiation patterns displayed for operating bands.

• Transactions of Materials Processing
• /
• v.11 no.2
• /
• pp.138-146
• /
• 2002

This paper is concerned with the simulation-based process design method involved non-steady state problem of tension levelling considering the elasto-plastic hardening behavior of a metallic strip by a commercial code ABAQUS/Standard. The tension levelling process is peformed to elongate the strip plastically in combination of tensile and bending strain by a controlled manner so that all longitudinal fibers in the strip have an approximately equal amount of length and undesirable strip shapes are corrected to the flat share. Objectives of this paper are the development of a general method for the design of a tension leveller by a finite element method and parameter studies for the deisgn variables such as the applied tension, the roll intermash includes the determination of the steady state using the simple unit of the tension levelling line and the effect of the finite element mesh size on the amount and distribution of the strain calculated. The analysis provides the information about the intermesh effect on the amount and final shapes of the strip and distribution of the strain in order to determine the amount elongation for correction of the irregular share.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.4691-4696
• /
• 2010

The This research paper deals with research on the 3D strip layout design of HEV UV terminal by utilizing the Cimatron Die Design, an automation module. To ensure smooth stamping of the product, strip layout was corrected for 33.5 degrees of slope, and blank layout of the double-width, 1-line, 1-pull out inner carrier was then optimized as a single arrangement. To mass-produce two different terminals from one common die, 3D strip layout design and die design were completed in 29 different processes.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.56-59
• /
• 1988

The main purpose of Set-up control of hot strip mill plant is to obtain the most regular thickness. Then the learning or adaptive computer control in hot strip rolling mill has been developed. But it is very difficult to keep the inter-stands load distribution ratio uniform; so that the deviation of strip flatness is not avoidable. This leads to the degradation of quality of the products. In this report, an improved method base on the steepest descent method including the computation of optimum step size. This method is applied to the off-line simulation. In consequence, the better balances of inter-stands load distribution is achieved in addition to improvements of output thickness of hot strip mill in POSCO.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.180-180
• /
• 2000

The shape of cold strip for the stainless process has been become issue in quality recently, and hence POSCO (Pohang Iron & Steel Co., Ltd) developed an automatic control system for strip shape in the sendzimir mill. The strip shape is measured by an outward measuring roll and is controlled by As_U roll and first intermediate roll. As_U roll consists of 8 saddles, which are controlled vertically. The fist intermediate rolls, which are controlled horizontally, consist of two pairs of rolls up and down. A developed shape control system is applied to real plant by using fuzzy logic and neural network method to control actuators; As_U roll and first intermediate roll. This system composes mainly of three parts as a real-time system, input to output conditioner board, and man-machine interface. The actual shape is recognized by neural network and converted into symmetric shape. The fuzzy controller, based on the shape from neural network and sensor, controls positions of the As_U roll and first intermediate roll. This paper verifies the shape controller performance. The experiments are made on line for the sendzimir mill. The shape control performance shows very efficient for the target tracking, shape symmetry, and fluctuation of shape.