• Proceedings of the Safety Management and Science Conference
• /
• 2004.05a
• /
• pp.1-4
• /
• 2004

Need safety diagnostic indicator pointer that is objective as estimation basis to be scientific and manages systematically safety existing condition and level for city gas facilities. Safety diagnostic indicator pointer can divide by greatly two. One is management (Software) side that one that differ with mechanical (Hardware) side that handle laying stress on equipment connected with safety manages organization and management connected with safety. Weight appropriates according to specific gravity that relevant element occupies in facilities. To give so big value in particular element in grant of weight pays attention because break balance of whole guideline and should gives. Finally, efficient safety net may see effect before self-regulation inside by minimum target establishment by government and legal, systematic countermeasure establishment for this, strict law application and each business proprietor and though activity and user's active safety activity forms harmony properly.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.2
• /
• pp.55-60
• /
• 2004

This paper describes the estimation method of hull girder response of ships due to springing. To this aim, nonlinear springing effect on the hull girder is evaluated including vertical, horizontal, and torsional deformation of the hull. The Timoshenko beam model is used to calculate the stress distribution on the hull girder. The quadratic strip method is employed to calculate the hydrodynamic forces and moments on the hull. In order to remove the irregular frequencies, 'rigid lid'is adopted on the hull free surface level and hydrodynamic coefficients are interpolated for asymptotic values. The results of example calculation show a reasonable agreement with previous results for both symmetric and anti-symmetric responses.

• Proceedings of the KSR Conference
• /
• 2001.05a
• /
• pp.212-216
• /
• 2001

Recently, it has been trending toward speed-up not only in the passenger car but in the freight cu. In this study, we thus performed stress analysis for the carbody for high speed container freight car in use and field test of the freight car in Gyungbu-line so that we may utilize the results as a design guide for speed-up hereafter- Five vertical loading conditions due to dynamic effect and the weight of the carbody and the container applied to locking devices of the carbody and its results are compared with that of a test, As a result, we found that there is need to complement the strength of the carbody in some measure when speed up the present freight car.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.2
• /
• pp.120-123
• /
• 2001

Despite the increasing necessity of accurate estimation of ring-stiffened cylinders'ultimate strength, the complex structural behavior of cylinders has made their design mainly depend on empirical formulas mostly based on limited test data rather than theoretical background. This paper has developed the imperfection method which enables the ultimate strength analysis of buckling-sensitive structures by combining two separate functions covered by common commercial finite element softwares, which are linear elastic buckling analysis and nonlinear stress analysis. Developed method was applied to two of the world most renowned softwares, MSC/NASTRAN and ABAQUS, for the analysis of ring-stiffened cylinders and unexpectedly big difference in their analysis results was found. This tells that many widely used commercial softwares have their different strong points and weak points and the choice of commercial software should be cautiously made after thorough inspection. This paper ends with some useful information about which of the two aforementioned softwares is more respectively for the linear elastic buckling analysis and the ultimate strength analysis of ring-stiffened cylinders.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.1
• /
• pp.63-68
• /
• 2004

The purpose of this study is to estimate the contribution of concrete and shear reinforcement, in shear carrying capacity, on concrete beams, reinforced with steel and/or FRP rods. The experimental tests for 12 concrete beams, reinforced with steel and/or FRP rods, are carried out. Experimental parameters includes the mechanical properties of reinforcements in shear and bending, and the ratio of shear reinforcement. This study compares the experimental results of shear carrying capacity in concrete beams, reinforced with steel and/or FRP rods, with the proposed equations. According to the experimental results, the effect of the concrete in concrete beams reinforced with FRP rods is decreased with decreasing Young's modulus of longitudinal tensile reinforcement. This results from the large deflection of concrete beams reinforced with decreasing Young's modulus of longitudinal tensile reinforcement. Also, the contribution of shear reinforcement is smaller than the calculated value, using the truss analogy. This results from the fact that the stress redistribution is not exhibited after the break of shear reinforcement.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.605-612
• /
• 2002

The objective of this study is to investigate the behavior of Visco-Elasto-Plastic materials of Silicate Grouted Sands due to external load. Uniaxial compression strength of silicate grouted sands was increased accordingly with curing time, but it was almost unchanged after 7days. A series of uniaxial compression creep tests were peformed for $\sigma$/$\sigma$$\sub$f/ = 8%,16% and 24%. The tested Silicated Grouted Sands exhibits three types of strains : elastic, plastic, viscoelastic. It is seen that the magnitude of the instantaneous recoverable strains $\varepsilon$$\sub$r/(o) is approximately independent of the unloading time. In this tests, The total creep strains( elastic, plastic, viscoelastic) are proportional to the stress level. Based on the constant creep test results, relationships between the time and the creep compliance are developed.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.7-14
• /
• 2001

구조물 하중에 의한 점성토 지반의 침하량을 보다 정확하게 평가하기 위해서는 지반 내의 흙요소가 경험하는 실제적인 응력경로와 이에 따른 변형양상이 적절하게 고려되어야만 한다. 따라서 본 연구에서는 축대칭 조건의 다양한 응력경로를 따라 발생하는 정규압밀 점성토의 변형 거동을 고찰한 기존의 실험적 연구결과를 바탕으로 응력경로법에 근거한 보다 간편하고 합리적인 침하량 평가기법을 제시하였다. 또한 본 연구에서는 제시된 평가기법을 기존의 1차원적인 침하량 평가기법들과 함께 실제와 유사한 조건을 가지는 가상지반의 침하량 산정에 적용해 보았으며, 동일한 조건에 대해 소성모델(MCC 모델)과 혼합압밀이론에 바탕을 둔 유한요소해석을 실시하였다. 그리고 이를 통해 얻어진 결과들을 비교.분석함으로써 기존 평가기법들의 문제점과 한계를 명확히 제시하였으며, 응력증분 평가방법이 침하량 평가에 미치는 영향을 분석하였다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1278-1284
• /
• 2008

This study carried out bender element tests in a calibration chamber in order to estimate the characteristics of soil specimen prepared in a calibration chamber. Basically, the purpose of bender element test is to measure the shear wave velocity. Bender element test cannot only confirm the status of soil specimen deposited in a chamber, but also estimate the consolidation process indirectly. In order to carry out bender element test in a calibration chamber, a pair of bender elements was installed inside the chamber, using the 'ㄷ' shaped frame. For the sandy soils having various relative densities in various stress conditions, the maximum shear modulus was estimated. From the comparison with bender element test results in a triaxial testing device, testing device and procedure was validated.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.484-491
• /
• 2008

The purpose of this study is to compare the cementation effect on cone resistance and DMT indices and to evaluate the deformation characteristic of cemented sand using cone resistance and dilatometer modulus. Specimens of various relative densities with three different cementation levels are prepared in a large calibration chamber under different vertical stress levels. Test result shows that the cone resistance and dilatometer modulus underestimate the deformation modulus of cemented sand, since in situ penetration tests such as CPT and DMT damage the cementation bonds during penetration. By regression analysis, the constrained modulus of cemented sand is related with the cone resistance and the dilatometer modulus.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.161-164
• /
• 1999

Estimation system of aging diagnosis using partial discharge(PD) is being highlighted as a research area for the residual lifetime pridiction of industrial equipment. But the application of PD requires complicated analysis method as expert system because the PD has complex progressing forms according to external stress. In this paper, it has been investigated the statistical distribution to express the 2D PD patterns of the diagnosis system using neural network(NN).