• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.915-922
• /
• 2017

The study on the thermal and oil resistance rubber composite, 2016. [6] predicted the lifetime of Fluorocarbon Rubber by accelerating aging at high temperature ($150^{\circ}C$, $175^{\circ}C$, $200^{\circ}C$). general rubber products are likely to exhibit different properties depending on the degradation factors such as temperature, humidity, ozone, light, emulsion, mechanical and electrical stress. To solve these problems, We compared the rate of change about tensile strength, elongation rate, volume change rate, weight change rate, thickness change rate, thermal conductivity in low temperature promoting aging on the basis of predictive lifetime of high temperature promoting aging. As a result of the review, the required life expectancy was satisfied, but there was a slight difference in the rate of change between the high-temperature promoted aging life result and the low temperature promoted aging life result. The cause was a reduction in "tensile strength / elongation" and an increase in "volume / weight / thickness" caused by the main chain decomposition of fluorine rubber due to aging at high temperature promoting aging. However, the low temperature promoting aging was caused by the curing reaction of fluorine rubber at $80^{\circ}C$. The tensile strength / elongation and volume / weight / thickness changes were small.

• Journal of the Korean association of regional geographers
• /
• v.6 no.1
• /
• pp.1-28
• /
• 2000

The purpose of this study is to clarify the suburbanization of manufacturing, and location and linkages of decentralized manufacturing from Metropolitan Pusan by means of case study on manufacturing location and linkages in the suburb of Metropolitan Pusan. Kimhae city and Yangsan-Gun toward which heavy decentralization of manufacturing from the Metropolitan Pusan has been done. Both hard data and soft data were used as the basic data. Hard data are the statistical data in statistical yearbooks and firm list in directories. The former consists of the number of establishments and employees classified by product type, firm size and unit area. The latter consists of owner's names, addresses, employee number, products and headquarters of firms. Soft data are the results of the interviews with the 242 owners of firms in the four case study areas selected by Proportional Stratified Sampling Method. The major findings are as follows: 1. The spatial variations of manufacturing in the suburb was regularized in the latter half of 1970's. The primary processes to decentralize manufacturing from Metropolitan Pusan were the birth, relocation and establishment of branches of the firms. Among them the relocation of small outer-oriented single-location firms from Pusan was the most important. 2. The spatial variations undergoing spatial expansion of manufacturing distribution and increase of agglomeration degree of manufacturing, proceeded from the adjacents of Metropolitan Pusan to the outer areas along the main transportation route. 3. The main factors which caused manufacturing to decentralize from the Metropolitan Pusan were firm policy and land for this policy. The main locational factors which induced the decentralizing manufacturing into the suburb were land, market and transportation. 4. The strength of linkages with the outside of the study area is stronger than that of linkages with the inside. There is distance-decay-function in the strength of linkages with the outside, and linkages with short distant areas are stronger than those with long distant areas. 5. The ranges of spatial linkages in procurement of materials, in subcontraction and in marketing are wider than those in ordering. 6. The main factors which cause the formation of linkages are different by types of linkages: monopolistic and oligopolistic supply are important in procurement linkages; characteristics of products and the subsequent marketing difficulties, in subcontraction linkages; fluctuation, cost reduction, insufficient facility and characteristics of products, in ordering linkages; subcontract, characteristics of product and the subsequent marketing difficulties, in marketing linkages. 7. The changes of linkages owing to locational changes of firms were great, and were greater in long distant areas than in short distant areas. 8. The main factor influencing on the changes of linkages was the easiness in the transportation of goods, movement of labour and contacts with customers. In conclusion, some facts described above were proved to be consistent with the results of proceeding studies in the other areas: influence of relocation of decentralizing firms on the suburbanization; the factors of manufacturing decentralization; spatial characteristics of linkages; linkage changes owing to relocation of firms. Some were proved to be partly consistent: locational factors inducing decentralized manufacturing into the suburb were proved to be inconsistent. I think that the results of previous studies on the other areas can be applicable to the explanation on the decentralization of Metropolitan manufacturing from the viewpoint of the suburb. For the better explanation on the decentralization of Metropolitan manufacturing, more empirical case studies on the suburbanization of manufacturing are necessary.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.1 s.53
• /
• pp.97-105
• /
• 2009

Development and use of blended cement concrete is gaining more importance in the construction industry with reference to durability mainly due to the pore refinement and reduction in permeability. Cracks play a major role on important parameters like permeability, rate of chloride ingress, compressive strength and thus affect the reinforcement corrosion protection. Furthermore, when a crack occurs in the cover concrete, the corrosion of the steel reinforcement may be accelerated because the deterioration causing factors can pass through the crack. In recent years the effect of cracking on the penetration of concrete has been the subject of numerous investigations. Therefore assessing the service life using blended concrete becomes obviously in considering the durability. In the present study, the corrosion assessment of composite concrete beams with and without crack with of 0.3mm using OPC, 30% PFA, 60% GGBS, 10% SF was performed using half cell potential measurement, galvanic potential measurement, mass loss of steel over a period of 60days under marine environmental conditions and the results were discussed in detail.

• Korean Journal of Adult Nursing
• /
• v.25 no.5
• /
• pp.483-493
• /
• 2013

Purpose: The purpose of this study was to examine late-onset hypogonadism, erectile dysfunction, depression, and quality of life among middle-aged male workers. Methods: The subjects included 343 men aged between 40 and 64, responded to self-report questionnaires on general characteristics, late-onset hypogonadism, erectile dysfunction, depression, and quality of life. Data were collected from May 16, 2012 to October 9, 2012 and analyzed using t-test, ANOVA, $x^2$-test, hierarchical multiple regression. Result: The prevalence rate of late-onset hypogonadism was 63.8% with high points in reduction of libido, energy, physical strength and endurance, and erectile function. There were significant differences in late-onset hypogonadism according to age($x^2$=8.98, p=.048) and in erectile dysfunction according to age(F=11.03, p<.001), monthly income(F=2.84, p=.024) and smoking( t=2.96, p=.018). Significant differences were also found in depression according to educational level(F=8.12, p<.001) and in quality of life according to monthly income(F=7.21, p<.001). The factors which influenced quality of life were late-onset hypogonadism, erectile dysfunction, depression, marital status and religion. Conclusion: Symptoms of erectile dysfunction can be improved by smoking cessation education program. In order to improve the life quality of middle-aged men, nursing intervention programs that would both provide proper knowledge on climacteric syndrome and alleviate symptoms should be designed while, at the same time, other programs to evaluate, prevent and control depression are developed.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.3
• /
• pp.59-65
• /
• 2007

Excess pore pressures in low permeability soils may not dissipate quickly enough and decrease the effective stresses inside the soil, which in turn may cause a reduction of the shear strength at the interface between the soil and the reinforcement in MSE walls. For this condition the dissipation rate of pore pressures is most important and it varies depending on wall size, permeability of the backfill, and reinforcement length. In this paper, a series of numerical analysis has been performed to investigate the effect of those factors. The results show that for soils with a permeability lower than $10^{-3}cm/sec$, the consolidation time gradually increases. The increase in consolidation time indicates the decrease in effective stress thus it will result in decrease in pullout capacity of the reinforcement as verified by the numerical analyses. It is also observed that larger consolidation time is required for longer reinforcement length (longer drainage path).

• Clinics in Shoulder and Elbow
• /
• v.1 no.1
• /
• pp.83-92
• /
• 1998

Fractures of the clavicles are extremely common, accounting for 5 to 10% of all injuries in the adult skeletal trauma. Despite this, nonunions and symptomatic malunions after clavicular fracture are uncommon. When these complications occur, however, they may be associated with 11 pattern of disability that includes not only pain but also impairment of upper extremity function. The purpose of this study was to clarify the outcome of clavicular fractures treated by conservatively, and emphasize treatment and factors that possibly predispose a clavicular fracture to poor function or nonunion. We evaluated 9] consecutive fractures of the middle-third of the clavicle in adults which had been treated conservatively. There were 59 males and 33 females ranging in age from 17 to 80 years (average 36.8 years). Nine of the 91 fractures (10%) had developed nonunion, and 4 fractures (4.4%) reported unsatisfactory results. No patients had significant impairment of range of motion or strength as a result of the injury. We found that initial shortening at the fracture of≥20mm(6 cases) had a highly significantly association with nonunion(P<0.0001). Final shortening of 20mm or more (4 cases) was associated with an unsatisfactory result, but not with nonunion(P<0.0001). Our results have led us to recommend the open reduction and internal fixation of severely displaced fractures of the middle third of the clavicle in adults patients.

• Polymer(Korea)
• /
• v.25 no.3
• /
• pp.441-449
• /
• 2001

Compatibilization of blends based on poly(phenylene ether) (PPE) and polyamide (PA) has been practiced with the incorporation of a copolymer formed by grafting polystyrene onto polybutadiene latex (g-BS) which is further functionalized with maleic anhydride (MAH) (g-BS*) to impart reactivity with amine groups of PA. The major focus has been placed on the effect of the various structural factors in g-BS8 on the phase morphology and mechanical performance of the blends. For the balance of impact strength and heat resistance, it was important to locate g-BS n particles inside of the PPE phase, which was accomplished by the proper control of the molecular weight and amount of PS in g-BS*. For g-BS*'s having constant molecular weight and amount of PS, the reduction of MAH content or increase of rubber particle size in g-BS* resulted in the increase of domain size and consequently loss in mechanical properties. Based on the comparison made with the conventional PPE/PA blend comprising MAH grafted PPE as a compatibilizer, it was confirmed that the comparable level of mechanical performance can be achieved by an appropriate g-BS* type material with improved whiteness index.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.3
• /
• pp.457-476
• /
• 2016

This was investigated on the major issues and research trends regarding the heat-treatment of woods through literature reviews. The principal heat-treatment technologies utilized for industrial purposes include the Plato-process (Netherlands), the Retification process (France), the OHT-process (Germany), and the Thermowood Process (Finland). Factors that mainly influence the heat-treatment process are the wood species, process temperature, processing time, and the heating medium (air, steam, vacuum, N2, oil, etc.). Researches on investigating the optimal conditions with these process conditions being the variables stand as the mainstream. Heat-treated woods present dimensional stability improvement, but mass loss and strength reduction, a wide variations for decaying inhibition, and insufficient resistance against mold, wood borer, and termites. For further improvement in respects of durability or resistance to biological degradation, necessity to search for more suitable heat treatment process and processing conditions fit for each wood species has been suggested. Exploiting new ways to utilize heat-treated wood and extending its range of use have been considered to be important matters that need more effort put into for the sustainable and sound environment as well as saving the wood resources.

• Journal of Ocean Engineering and Technology
• /
• v.20 no.6 s.73
• /
• pp.123-129
• /
• 2006

The mechanical properties of bellows, such as the extensibility and the strength can be changed depending on the shape. For the shipbuilding material, it is desirable that the fatigue life is long due to the elastic property and the reduction of thermal stress in piping system. Nowadays, the domestic production and design of bellows are based on the E.J.M.A. Code. Therefore, the design standard is in need because of much errors and lack of detailed analysis. In this study, it is attempted to find out the optimal shape of U-type bellows using the finite element analysis. The design factors, mountain height, length, thickness, and the number of convolutions are considered and the proper values are chosen for the simulation. The results shaw that as the number of convolutions reduces, the volume decreases while the stress increases. However, as the number of convolutions increases, the volume increases above the standard volume and the stress obviously increases. In addition, the effect of the thickness of bellows on the stress is very large. Both of the mass and stress are decreasing at a certain lower value region. Also, we investigated shape optimization with considering maximum stress distribution tendency.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.5
• /
• pp.627-637
• /
• 1985

The combustion process and the performance of a diesel engine are seriously affected by the ignition delay period of the fuel used. Some methods for improving the combustion process in the engine cylinder are to well match the strength of air swirl with the space of sprays in the cylinder, to blend an ignition improver in the fuel, to inject a small amount of auxiliary fuel prior to main injection and so on. Recently, the improvement of fuel economy and the reduction of exhaust smoke and NO have been successfully achieved by supplying diesel engines with emulsified fuel. However, it is very difficult to know real combustion mechanism under such special conditions, because of many factors affecting on the combustion process in practical reciprocating engine. In the present paper, the combustion processes of diesel fuel and emulsion fuel were tried to improve and to observe by making contact with various lean pre-mixtures in the hot air stream duct. This hot air stream method has an advantage that the spontaneous combustion process can be observed under a simplified condition.