• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.5
• /
• pp.41-50
• /
• 2014

This study evaluated the bonding property of fiber and flexural behavior of fiber reinforced concrete. Amorphous steel fiber, hooked steel fiber and polyamide fiber was used for evaluation of bonding property and flexural behavior. As a result, the hooked steel fiber was pulled out from matrix when peak stress. However amorphous steel fiber occurred shear failure because bonding strength between fiber and matrix was higher than tensile strength of fiber. Polyamide fibers occurred significantly displacement to peak stress because of elongation of fiber. After that peak stress, fiber was cut off. Amorphous steel fiber reinforced concrete had a greater maximum flexural load compared with hooked steel fiber reinforced concrete because bonding performance between fiber and matrix was high and mixed population of fiber was many. However flexural stress was rapidly reduced in load-deflection curve because of shear failure of fiber. Flexural stress of hooked steel fiber reinforced concrete was slowly reduced because fiber was pulled out from the matrix. In the case of polyamide fiber reinforced concrete, flexural stress was rapidly lowered because of elongation of fiber. However flexural stress was increased again because of bonding property between polyamide fiber and matrix. The pull-out properties of the fiber and matrix has effect on the deformation capacity and flexural strength of fiber reinforced concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.53-56
• /
• 2005

This paper investigates the effect of ductile deformation behavior of high performance hybrid fiber-reinforced cement composites (HPHFRCCs) on the shear behavior of coupling beams to lateral load reversals. The matrix ductility and the reinforcement layout were the main variables of the tests. Three short coupling beams with two different reinforcement arrangements and matrixes were tested. They were subjected to cyclic loading by a suitable experimental setup. All specimens were characterized by a shear span-depth ratio of 1.0. The reinforcement layouts consisted of a classical scheme and diagonal scheme without confining ties. The effects of matrix ductility on deflections, strains, crack widths, crack patterns, failure modes, and ultimate shear load of coupling beams have been examined. The combination of a ductile cementitious matrix and steel reinforcement is found to result in improved energy dissipation capacity, simplification of reinforcement details, and damage-tolerant inelastic deformation behavior. Test results showed that the HPFRCC coupling beams behaved better than normal reinforced concrete control beams. These results were produced by HPHFRCC's tensile deformation capacity, damage tolerance and tensile strength.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.2
• /
• pp.189-196
• /
• 1994

Quality assurance in the process of manufacturing high strengh bolt sets used in the frictional joints of structures in one of important concern to users as well as to manufactures. In case of occurrences of either defective or low-quality products, even if they are quite rare, some systematic means of localizing the cause-characteristics and matching to corresponding production process is necessary. Control chart of torque factor is the primary indicatir in finding defectiveness of the products. Use of correlation diagrams ofnhardness of the bolt set presents in part a way of screening the cause. Retest data of the bolt set provide additional ideas of localizing the cause, for which theoretical background is presented in this regard. A process-characteristics matrix relating the causes of low quality to the corresponding process of manufacturing, which is of prime importance for the feedback control of production, is also proposed. Finally general features of control to assure quality of the set is described.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.82-87
• /
• 2012

For different ferrite-pearlite matrix structure, contain more than 90% spheroidal ratio of graphite, GCD 45-3, GCD 50, GCD 60 series and 70%, 80%, 90% spheroidal ratio of graphite, GCD 40, GCD 45-1, GCD 45-2 series, this paper has carried out rotary bending fatigue test, estimated maximum and mean size of spheroidal graphite, investigated correlation. It was concluded as follows. (1) Fatigue limit in $10^7$cycles and numbers of spheroidal graphite per 1$mm^2$ was linear relation. (2) projection area of graphite can be used to predict fatigue limit of Ductile Cast Iron. The Statistical distribution of extreme values of projection area of defects may be used as a guideline for the control of inclusion size in the steelmaking processes.

• Journal of Korea Foundry Society
• /
• v.13 no.3
• /
• pp.276-284
• /
• 1993

The interfacial phenomena between intermetallic compounds and Al matrix have been studied at $680^{\circ}C$ for various holding time under argon atmosphere. Model experiments were performed using Fe, Ni and Ti wire to observe the interfacial phenomena. The interfacial phenomena between intermetallic compounds and Al matrix were analysed by optical microscope, SEM and EDX. The results of EDX and XRD showed that the interfacial zones of intermetallic compounds/Al matrix were composed of several intermetallic layers. The reaction layer was varied with holding time and heating temperature. The investigation of interfacial zones in the specimen as a function of heat treatment time at $680^{\circ}C$ indicated that the best heat treatment condition for squeeze casting was $680^{\circ}C$ for 5min.

• Archives of Metallurgy and Materials
• /
• v.67 no.4
• /
• pp.1543-1546
• /
• 2022

The aluminum composite with dispersed high entropy alloy were developed by stir casting involving the powder-in-tube method. First, Al_0.5CoCrCuFeNi high entropy alloy (HEA) powder was made by mechanical alloying, and the powder was extruded in a tube-type aluminum container to form HEA precursor. The extruded HEA precursor was then dispersed in the aluminum matrix via stir casting. As a result, Fe-Cr-Ni based high-entropy phases was uniformly formed in the aluminum matrix, revealing ~158, 166, 235% enhancement of tensile strength by incorporating 1, 3, and 5 wt% HEA particles, respectively.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.1
• /
• pp.107-111
• /
• 2011

Polypropylene(PP)/carbon fiber(CF)/multi-walled carbon nanotube(MWCNT) nanocomposites along with various CF and MWCNT contents were prepared in a Twin screw extruder. Electrical, mechanical property and morphology were investigated with a variation of CF and MWCNT contents. From the surface resistance of PP/CF/MWCNT composites, MWCNT can increase the conductivity of composites compared with PP/CF composites without MWCNT. It is suggested that MWCNT and CF can make the conductive network in the polymer matrix. Flexural modulus and Izod impact strength of the PP/CF/MWCNT composites were improved with the increase of CF contents. Morphology showed that length of CF in polymer matrix was shortened by torque during melt mixing with MWCNT. As a result of this phenomenon, the impact strength of composites was somewhat decreased.

• The Journal of Korean Academy of Prosthodontics
• /
• v.30 no.4
• /
• pp.481-492
• /
• 1992

Author measured the bonding strength between Dental Porcelain and Nonprecious Dental Alloy and analyzed diffusion Phenomena at the interfaceby by Auger electron spectroscopy and also Electron spectroscopy for Chemical Analysis. The each specimen was sputtered with Al, Cr, In and Sn. 1. Ni whic is the main element of the matris of dental nonprecious alloy diffuse more than the other element and the Ni diffusion rate of each specimen was well coordinated with the bonding strength of each. 2. The Sn thin film suppress the diffusion rate of Ni of matrix into the Dental Porcelain than the In or Cr thin films. 3. The Al thin film suppress the diffusion rate of Ni than the Sn thin film. 4. The main coponent of dental porcelain : Al, Si, Mo diffused into the matrix of alloy. It means that the each element of dental alloy and dental porelain diffused into the each other part.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.115-116
• /
• 2022

This study incorporates fine waste glass (GS) as a replacement for natural sand (NS) in fly ash (FA) based alkali activated mortar (AAm). AAms were heated at elevated temperature of 200℃, 400℃, 600℃, and 800℃ to explore the residual mass, compressive strength, thermal expansion and change in microstructure of matrix. Results showed greater resistance of AAms with increasing GS content to 50% at each temperature. Owing to the melting of GS at 800℃, the greater matrix bond was observed for AAm incorporating 75% and 100% GS as a result, the residual compressive strength was increased.

• Journal of the Korean Ceramic Society
• /
• v.45 no.4
• /
• pp.204-207
• /
• 2008

This paper presents a new process for producing SiC fiber-SiC matrix(SiC/SiC) composites by reaction sintering. The processing strategy for the fabrication of the SiC/SiC composites involves the following: (1) infiltration of the SiC fiber fabric using a slurry consisting of Si and C precursors, (2) stacking the slurry-infiltrated SiC fiber fabric at room temperature, (3) cross-linking the stacked composites, (4) pyrolysis of the stacked composites, and (5) hot-pressing of the pyrolyzed composites. It was possible to obtain dense SiC/SiC composites with relative densities of >96% and a typical flexural strength of ${\sim}400$ MPa.