• Journal of the Korean Institute of Gas
• /
• v.12 no.4
• /
• pp.14-20
• /
• 2008

In this numerical study, the leakage safety of the LNG tank in which is constructed by membrane inner tank-plywood-polyurethane form-plywood-prestressed concrete structures has been presented for four leakage analysis models. The LNG leak criterion of the tank wall with a storage capacity of $200,000\;m^3$ is analyzed based on the thermal resistance technique. This means that if the cryogenic temperature of a leaked LNG is detected at the outer side of the PC wall, it may be leaked through the wall thickness of the tank. The calculated results based on the thermal resistance method between two walls show that the plywood, PUF, and another plywood walls may block the leakage of the leaked LNG even though the strength of these walls is already collapsed by a leaked LNG pressure. But, the leaked LNG may pass the thickness of the prestressed concrete wall for a period of elapsed time even though the PC outer tank supports the leaked LNG pressure. Thus, the PC outer tank may extend the leakage time of a leaked LNG.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.6 no.3
• /
• pp.227-235
• /
• 2004

Tunneling in rock mass produces two types of damages in the vicinity of a tunnel: structural and constructional damages. Structural damage represents the damage induced by the unbalance of geostatic stress caused by the tunneling, and constructional damage is the damage produced during the construction. In this study, formulations of tangential and radial stresses in the elastic and plastic zones near a tunnel, and the calculation of radius of plastic zone surrounding a tunnel are introduced by modifying the Hoek-Brown criterion of 2002 edition, which has capability of considering in situ rock mass characteristics and construction damage. From the parametric study, influences of rock mass quality, uniaxial compressive strength of intact rock, and the dimension of the tunnel on the plastic zone are investigated. The accuracy of the proposed approach is evaluated by comparing with results from the previous study.

• Geomechanics and Engineering
• /
• v.5 no.5
• /
• pp.463-483
• /
• 2013

Considering the influences of fluid penetration, casing, excavation processes of wellbore and perforation tunnels, the seepage-deformation finite element model of oil and gas well coupled with perforating technique is established using the tensile strength failure criterion, in which the user-defined subroutine is developed to investigate the dynamic evolvement of the reservoir porosity and permeability. The results show that the increases of perforation angle and decreases of perforation density lead to a higher fracture initiation pressure, while the changes of the perforation diameter and length have no evident influences on the fracture initiation pressure. As for initiation location for the fracture in wellbore, it is on the wellbore face while considering the presence of the casing. By contrast, the fractures firstly initiate on the root of the tunnels without considering casing. Besides, the initial fracture position is also related with the perforation angle. The fracture initiation position is located in the point far away from the wellbore face, when the perforation angle is around $30^{\circ}$; however, when the perforation angle is increased to $45^{\circ}$, a plane fracture is initiated from the wellbore face in the maximum horizontal stress direction; no fractures was found around perforation tunnels, when the angel is close to $90^{\circ}$. The results have been successfully applied in an oilfield, with the error of only 1.1% comparing the fracture initiation pressure simulated with the one from on-site experiment.

• Geotechnical Engineering
• /
• v.3 no.2
• /
• pp.55-70
• /
• 1987

An analytical solution procedure is described to estimate the developed passive lateral earth Pressures behind a vertical rigid retaintng wall rotating about its toe into a mass of cohesionless soil. Various stases of wall rotation, starting from an at-rest state to an initial Passive state to a full Passive state, are considered in the analysis. Condition of failure defined by a modified Mohr-coulomb criterion, together with equilibrium conditions, is used to obtain the necessary equations for the solution. Using methods of stress characteristics and numerical finite difference, a complete solution within and on the boundaries of the entire solution domain is made possible. The variations of the soil shear strength and the wall friction at various depths and stages of wall rotation are also taken into account in the analysis. The results predicted by the developed method of analysis are compared with those obtained from the experimental model tests on loose and dense sand. The comparisons show good agreements at various stages of retaining wall rotation Fin- ally, results of analytical parametric study are presented to demonstrate the effects of wall fric- tion on the resultant thrust and distribution of developed lateral earth pressures.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.1
• /
• pp.103-110
• /
• 2003

The development of reinforced-roadbed material in substitute for existing roadbed is necessary to protect its failure from the dynamic stress and vibration caused by the traveling of the high-speed and heavy trains. The water quenched blast furnace slag having potential hydraulic reactivity is one of the materials in substitute for soil reinforced-roadbed. We carried out the study of basic properties of roadbed material using Portland cement and CSA(calcium sulphoaluminate) as the activator for the evaluation of its application. As the result of the strength test, this material satisfied design criterion for reinforced-roadbed. Optimum mixing ratio of this reinforced-roadbed material was 15 ~ 17.5 percent of cement and 2.5 percent of CSA by weight of the blast furnace slag. Especially, as permeability is above $10^{-3}$cm/sec, this material proved to have functions of both reinforced roadbed and drainage layer.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.3
• /
• pp.183-193
• /
• 1987

After clay particles have been sedimented isotropically, the clay deposits have been consolidated under $K_0$-stress system. Therefore, in order to predict the behavior in-situ of normally consolidated clays, the effect of $K_0$-consolidation should be considered. A series of undrained and drained triaxial compression tests was performed on remolded specimens of clay consolidated under both $K_0$-and isotropic stress systems and the effect of $K_0$-consolidation was investigated. $K_0$-consolidation has much effect on the deviator stress, especially at initial deformation stage of consolidated-undrained tests, but has little effect on the principal effective stress ratio. Thus, the undrained strength behavior of $K_0$-consolidated samples can not be predicted from isotropically consolidated test data. However, the failure envelop, provided by the maximum principal effective stress ratio failure criterion, is unique and curved.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.95-102
• /
• 2006

In this paper, we present the performance analysis and design of a multi-path searcher operating over Rayleigh fading channels when multiple transmit antennas are employed in the down-link of W-CDMA system. The simulation results for the receiver operating characteristics (ROC) for 1, 2, and 4 transmit antennas are presented to corroborate the theoretical analyses. We also propose a procedure to find the optimum parameters of double-dwell serial searcher according to the number of the multiple transmit antennas. Our analyses and simulations indicate that post-detection integration is not necessary when the number of transmit antennas is more than two. Finally, we found that increasing transmit diversity order does not necessarily improve the detection performance when the received pilot signal strength is relatively low. Therefore, this gives us a practical criterion on increasing transmit diversity order.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.6
• /
• pp.29-40
• /
• 2004

The bearing capacity of drilled shaft is affected by several factors, such as shaft length, shape, surface roughness, young's modulus of geomaterials and shaft, soil strength, confining stress and so on. However, there has been no design method of drilled shaft considering all factors mentioned above. Moreover, since geomaterials are simply classified as sand, clay and rock, there was no design criterion for IGM (Intermediate Geomaterials). Therefore, the rigorous design approach of drilled shaft was not possible by classical design method. However, since these characteristics were not considered in classical theories, bearing capacity was generally different ken practical value. In this study, the bearing capacity of drilled shaft with the IGM's theory was compared with those of classical theories. The results showed that classical method showed smaller values of bearing capacity than those of field load transfer data. Moreover, the evaluated value of bearing capacity with IGM theory corresponded fairly well with those of field data.

• Earthquakes and Structures
• /
• v.19 no.5
• /
• pp.395-409
• /
• 2020

With verifications through many relevant researches in the past few decades, adopting the equivalent lateral force procedure for designing seismically isolated structures as a preliminary or even final design approach has become considerably mature and publicly acceptable, especially for seismic isolation systems that mechanically exhibit bilinear hysteretic behavior. During the design procedure, in addition to a given seismic demand, structural designers still need to previously determine three parameters, such as mechanical properties of seismic isolation systems or design parameters and performance indices of seismically isolated structures. However, an arbitrary or improper selection of given parameters might cause diverse or even unacceptable design results, thus troubling structural designers very much. In this study, first, based on the criterion that at least either two design parameters or two performance indices of seismically isolated structures are decided previously, the rationality and applicability of design results obtained from different conditions are examined. Moreover, to consider variations of design parameters of seismically isolated structures attributed to uncertainties of mechanical properties of seismic isolation systems, one of the conditions is adopted to perform bounding analysis for seismic isolation design. The analysis results indicate that with a reasonable equivalent damping ratio designed, considering a specific variation for two design parameters (the effective stiffness and equivalent damping ratio) could present more conservative bounding design results (in terms of isolation displacement and acceleration transmissibility) than considering the same variation but for two mechanical properties (the characteristic strength and post-yield stiffness).

• Korean Membrane Journal
• /
• v.7 no.1
• /
• pp.1-18
• /
• 2005

The permeate flux decline due to membrane fouling can be addressed using a variety of theoretical stand-points. Judicious selection of an appropriate theory is a key toward successful prediction of the permeate flux. The essential criterion f3r such a decision appears to be a detailed characterization of the feed solution and membrane properties. Modem theories are capable of accurately predicting several properties of colloidal systems that are important in membrane separation processes from fundamental information pertaining to the particle size, charge, and solution ionic strength. Based on such information, it is relatively straight-forward to determine the properties of the concentrated colloidal dispersion in a polarized layer or the cake layer properties. Incorporation of such information in the framework of the standard theories of membrane filtration, namely, the convective diffusion equation coupled with an appropriate permeate transport model, can lead to reasonably accurate prediction of the permeate flux due to colloidal fouling. The schematic of the essential approach has been delineated in Figure 5. The modern approaches based on appropriate cell models appear to predict the permeate flux behavior in crossflow membrane filtration processes quite accurately without invoking novel theoretical descriptions of particle back transport mechanisms or depending on adjust-able parameters. Such agreements have been observed for a wide range of particle size ranging from small proteins like BSA (diameter ${\~}$6 nm) to latex suspensions (diameter ${\~}1\;{\mu}m$). There we, however, several areas that need further exploration. Some of these include: 1) A clear mechanistic description of the cake formation mechanisms that clearly identifies the disorder to order transition point in different colloidal systems. 2) Determining the structure of a cake layer based on the interparticle and hydrodynamic interactions instead of assuming a fixed geometrical structure on the basis of cell models. 3) Performing well controlled experiments where the cake deposition mechanism can be observed for small colloidal particles (< $1\;{\mu}m$). 4) A clear mechanistic description of the critical operating conditions (for instance, critical pressure) which can minimize the propensity of colloidal membrane fluting. 5) Developing theoretical approaches to account for polydisperse systems that can render the models capable of handing realistic feed solutions typically encountered in diverse applications of membrane filtration.