The out-of-phase thermo-mechanical fatigue (OP TMF) in a <001> oriented single crystal nickel-based superalloy CMSX-4 has been studied. OP TMF life was less than a half of low cycle fatigue(LCF) life in spite of a small hysteresis loop area of OP TMF compared to that of LCF. The failure was caused by the initiation of a crack at the oxide-layered surface followed by its planar growth along the <100> ${\gamma}$ channel in both LCF and OP TMF. However, deformation twins appeared near the major crack of OP TMF. The multiple groups of parallel twin plates on {111} planes provided a preferential path for crack propagation, which caused a significant decrease in OP TMF life. Additionally, the analysis on the surface crack morphology revealed that the tensile strain at the minimum temperature of OP TMF was found to accelerate the crack propagation.
High temperature high cycle and low cycle fatigue deformation behavior of automotive heat resistant aluminum alloys (A356 and A319 based) were investigated in this study. The microstructures of both alloys were composed of primary Al-Si dendrite and eutectic Si phase. However, the size and distribution for eutectic Si phase varied: a coarse and inhomogeneous distributed was observed in alloy B (A319 based). A brittle intermethallic phase of ${\alpha}-Fe\;Al_{12}(Fe,Mn)_3Si_2$ was detected only in B alloy. Alloy B exhibited high fatigue life only under a high stress amplitued condition in the high cycle fatigue results, whereas alloy A showed high fatigue life when stress was lowered. With regard to the low-cycle fatigue result ($250^{\circ}C$) showing higher fatigue life as ductility increased, alloy A demonstrated higher fatigue life under all of the strain amplitude conditions. Fractographic observations showed that large porosities and pores near the outside surface could be the main factor in the formation of fatigue cracks. In alloy B. micro-cracks were formed in both the brittle intermetallic and coarse Si phasese. These micro-cracks then coalesced together and provided a path for fatigue crack propagation. From the observation of the differences in microstructure and fractography of these two automotive alloys, the authors attempt to explain the high-temperature fatigue deformation behavior of heat resistant aluminum alloys.
In coal mining activities, the abutment stress of the coal has to undergo cyclic loading and unloading, affecting the strength and seepage characteristics of coal; additionally, it can cause dynamic disasters, posing a major challenge for the safety of coal mine production. To improve the understanding of the dynamic disaster mechanism of gas outburst and rock burst coupling, triaxial devices are applied to axial pressure cyclic loading-unloading tests under different axial stress peaks and different pore pressures. The existing empirical formula is use to perform a non-linear regression fitting on the relationship between stress and permeability, and the damage rate of permeability is introduced to analyze the change in permeability. The results show that the permeability curve obtained had "memory", and the peak stress was lower than the conventional loading path. The permeability curve and the volume strain curve show a clear symmetrical relationship, being the former in the form of a negative power function. Owing to the influence of irreversible deformation, the permeability difference and the damage of permeability mainly occur in the initial stage of loading-unloading, and both decrease as the number of cycles of loading-unloading increase. At the end of the first cycle and the second cycle, the permeability decreased in the range of 5.777 - 8.421 % and 4.311-8.713 %, respectively. The permeability decreases with an increase in the axial stress peak, and the damage rate shows the opposite trend. Under the same conditions, the permeability of methane is always lower than that of helium, and it shows a V-shape change trend with increasing methane pressures, and the permeability of the specimen was 3 MPa > 1 MPa > 2 MPa.
Connections with damage concentrated to pre-selected components can enhance seismic resilience for moment resisting frames. These pre-selected components always yield early to dissipate energy, and their energy dissipation mechanisms vary from one to another, depending on their position in the connection, geometry configuration details, and mechanical characteristics. This paper presents behaviour insights on two types of beam-to-beam connections that the angles were designed as energy dissipation components, through the results of experimental study and finite element analysis. Firstly, an experimental programme was reviewed, and key responses concerning the working mechanism of the connections were presented, including strain distribution at the critical section, section force responses of essential components, and initial stiffness of test specimens. Subsequently, finite element models of three specimens were established to further interpret their behaviour and response that were not observable in the tests. The moment and shear force transfer paths of the composite connections were clarified through the test results and finite element analysis. It was observed that the bending moment is mainly resisted by axial forces from the components, and the dominant axial force is from the bottom angles; the shear force at the critical section is primarily taken by the slab and the components near the top flange. Lastly, based on the insights on the load transfer path of the composite connections, preliminary design recommendations are proposed. In particular, a resistance requirement, quantified by a moment capacity ratio, was placed on the connections. Design models and equations were also developed for predicting the yield moment resistance and the shear resistance of the connections. A flexible beam model was proposed to quantify the shear resistance of essential components.
Jinhai Zhao;Weilong Zhu;Wenbin Sun;Changbao Jiang;Hailong Ma;Hui Yang
Geomechanics and Engineering
/
제38권3호
/
pp.215-229
/
2024
Because of the various patterns of deep-water inrush and complicated mechanisms, accurately predicting mine water inflows is always a difficult problem for coal mine geologists. In study presented in this paper, the water inrush channels were divided into four basic water diversion structures: aquifer, rock fracture zone, fracture zone and goaf. The fluid flow characteristics in each water-conducting structure were investigated by laboratory tests, and multistructure and multisystem coupling flow analysis models of different water-conducting structures were established to describe the entire water inrush process. Based on the research of the water inrush flow paths, the analysis model of different water inrush space structures was established and applied to the prediction of mine water inrush inflow. The results prove that the conduction sequence of different water-conducting structures and the changing rule of permeability caused by stress changes before and after the peak have important influences on the characteristics of mine water-gushing. Influenced by the differences in geological structure and combined with rock mass RQD and fault conductivity characteristics and other mine exploration data, the prediction of mine water inflow can be realized accurately. Taking the water transmitting path in the multistructure as the research object of water inrush, breaking through the limitation of traditional stratigraphic structure division, the prediction of water inflow and the estimation of potentially flooded area was realized, and water bursting intensity was predicted. It is of great significance in making reasonable emergency plans.
탄소성(彈塑性) 변형경화(變形硬化) 거동(擧動)을 하는 흙은 토질(土質)의 상태(狀態)와 시험조건(試驗條件)에 따라 다양(多樣)한 응력경로(應力經路)를 갖는다. 체적비(體積比) ${\upsilon}$인 흙을 주응력공간(主應力空間)에서 표시(表示)하면 불규칙육각형(不規則六角形)피라밋에 캡을 씌운 형상(形狀)이다. 캡은 ${\upsilon}$값이 변(變)하면 그 크기가 달라지나 형상(形狀)은 항상 닮은 꼴이며 소성체적변형(塑性體積變形)의 증감(增減)에 따라 이동(移動)이 결정된다. 이와 같은 토질특성(土質特性)을 반영하여 현재(現在)까지 많은 학자(學者)들이 캡모델을 연구발표(硏究發表)하였으며 본(本) 연구(硏究)에서는 비선형(非線形) 탄성변형(彈性變形) 경화(硬化) 소성(塑性) 캡과 Mohr-Coulomb의 파괴곡면(破壞曲面)을 접합(接合)한 흙의 구성(構成) 모델(M-C 캡모델)의 함수식(函數式)을 유도(誘導)하였다. 변형경화(變形硬化) 소성(塑性) 캡모델을 사용(使用)한 해석(解析)의 결과(結果)에 의하면 정규압밀(正規壓密) 상태(狀態)에서는 전단(剪斷)을 통한 경화(硬化)와 소성(塑性)흐름(캡의 이동(移動))의 형상(形狀)을 보여주고 있으나 과압밀상태(過壓密狀態)의 전단(剪斷)에서는 파괴포락선(破壞包絡線)에 도달할 때까지 탄성거동(彈性擧動)을 보이고 캡은 이동(移動)하지 않았다.
본 연구는 2017년 11월 15일에 발생한 규모 5.4의 포항지진을 대상으로 영일만항 안벽 및 배면에서 발생한 피해의 메커니즘을 규명하는 것이 목적이다. 현장조사 등에 의해 영일만항은 케이슨이 5cm~15cm 정도의 수평변위가 발생하였고, 뒤채움 지반에서는 10cm 이상의 침하가 발생하였다. 이에 대한 원인을 규명하기 위해 2차원 유효응력해석을 수행하였다. 입력 지진하중은 포항구항의 기반암에서 계측된 지진가속도($3.25m/s^2$)를 이용하였다. 수치해석 결과 배후지의 뒤채움 지반내 국부적으로 과잉간극수압이 증가하여 유효응력이 감소한 것으로 밝혀졌다. 이로 인해 케이슨의 경우 수평방향으로 약 14cm의 변위가 발생하였고, 3cm 정도 침하하였다. 뒤채움 지반의 경우 6cm~9cm 정도 침하한 것으로 나타났다. 이는 현장조사와도 유사한 결과임이 밝혀졌다. 또한, 뒤채움 지반내 유효응력 경로 및 응력-변형률 거동으로부터 반복적 하중에 의해 지반이 Mohr-Coulomb의 파괴선에 근접하는 것으로 나타났고, 이는 과잉간극수압의 증가에 따른 유효응력의 소실에 의한 지지력의 감소로 판단된다.
n형 SiC 반도체에서 적층 결함이 열전 물성에 미치는 영향에 대해 연구하였다. -SiC 분말 성형체를 질소 분위기에서 1600~2100 ℃, 20~120분간 열처리해서 30~42 %의 기공률을 갖는 다공질 SiC 반도체를 제작하였다. X선 회절 분석으로 적층 결함량, 격자 스트레인 및 격자 상수를 산출하였고, 미세 구조 분석을 위해서 기공률 및 비표면적 측정과 함께, 주사 전자현미경 (SEM), 투과 전자현미경 (TEM) 및 고분해능 전자현미경 (HREM) 등을 관찰하였다. Ar 분위기 550~900 ℃에서 도전율과 Seebeck 계수를 측정 및 산출하였다. 열처리 온도가 높을수록, 처리 시간이 길어질수록 캐리어 농도 증가 및 입자와 입자간의 연결성 향상에 의해 도전율이 향상되었다. 도너로 작용하는 질소의 고용으로 Seebeck 계수는 음(-)의 값을 나타내었고, 도전율과 마찬가지로 열처리 온도 및 시간이 상승함에 따라 Seebeck 계수의 절대 값이 증가하였다. 이는 적층 결함의 감소, 즉 입자 및 결정 성장과 함께 적층 결함 밀도의 감소에 의해 포논의 평균 자유 행정이 증가해서 결과적으로 포논-드랙 효과에 의한 Seebeck 계수의 향상으로 나타난 것으로 판단된다.
탄성파 피에조콘 관입 시험(SCPTU)은 동적 물성을 포함한 지반의 공학적 특성 평가에 가장 유용 한 조사 기법 중의 하나이다. 본 연구에서는 국내 지반에 대한 실질적 활용 연구로서 국내 대표적 퇴적지층 발달 지역인 부산과 인천을 대상으로 각각 두 부지와 네 부지에서 SCPTU를 수행하였다. 현장에서 SCPTU로부터 획득한 파형 신호에 대해 교차법을 이용한 신호 판독을 실시하여 깊이별 전단파의 초기 도달 시점 및 그에 따른 깊이별 도달 시차를 결정하였다. 이를 토대로 Snell의 법칙에 근간한 굴절 전파경로법을 이용하여 전단파 속도(VS) 주상도를 도출하였으며, 대체로 깊이별 VS 분포는 콘 선단 저항력(qt) 분포 경향과 유사하게 나타났다. 인천 지역에서는 병행된 일반적인 다운홀 탄성파 시험에 비해 SCPTU를 보다 깊은 심도까지 효율적으로 수행할 수 있었다. 이와 더불어, 일반적인 CPTU 자료의 지진공학적 활용을 목적으로 SCPTU로부터 측정된 결과를 토대로 VS와 콘 관입 특성값의 상관관계를 분석 도출하였다. 다중 회귀 분석을 수행하여 전단파 속도와 콘 관입 특성값 중 네가지의 독립변수인 콘 관입 저항력(qt), 주면 마찰력(fs), 유효상재응력($\sigma$'v0), 간극수압계수(Bq) 간의 상호 관련성을 정량적으로 평가하였으며, 특히 흙 분류 지수인 Ic 값에 의하여 객관적으로 구분된 사질토 및 점토와 전체 토사에 대한 변수별 경험적 상관식을 제안하였다. SCPTU의 다운홀 탄성파 시험과 일반적인 CPTU의 대상 변형률 수준이 다름에도 불구하고 본 연구에서 도출 제안된 VS와 CPTU 특성값의 상관관계는 국내 퇴적 지반에 대한 VS의 예측에 매우 유용하였으며, 기존 해외 연구의 상관관계에 비해서도 높은 상관성을 보였다.> (p value<0.000) 낮춤으로써, 전통적인 2문 대칭 조사법보다 우수한 방법으로 확인되었다. 반면에 공용보상체의 사용은 평균 DII를 $3.7\%$ 낮추지만(p value=0.260) 평균 $D_{max}$는 거의동일 하여($0.3\%$ 감소, p value=0.867), 전통적인 방법보다 우수성이 크게는 없는 것으로 평가되었다. 그러나 환자의 체곡선이 보상체와 잘 일치하는 경우에는 DII가 $18\%$까지 감소하였다. 결론 : Multistatic field 방법은 모든 환자에 대하여 선량분포의 균일성을 전반적으로 향상시키는 효과적인 방법으로 평가되는 반면 공용보상체의 사용은 보상체의 크기가 환자의 체 윤곽과 잘 일치하는 경우만 효과적으로, 적용의 범위에는 한계가 있는 방법으로 평가되었다.비교하여 계통에 따르는 차이가 있음을 알 수 있었다. 그러므로 가임기 여성의 방사선 진단 및 치료시 Rugh의 10일 법칙을 적용하여 착상전기 방사선 조사로 인한 부작용들을 적극적으로 예방하는 것이 매우 중요하다고 생각한다.equirements of the prematured infants during the early weeks of life. 모든 치근단 수준에서 비표준화 medium 크기 master cone 사용군이 ISO 표준화 규격의 master cone 사용군에 비해 유의하게 높은 gutta-percha 면적비를 나타내었다 (p < 0.01). 비표준화 medium크기 master cone 사용군에서는 표준화 규격의 master cone 사용군에 비해 유의하게 적은 수의 accessory cone이 사용되었다 (p < 0.01). 대학생간에는 유의한 차이(p<0.05)가 인정되었
탄성파 피에조콘 관입 시험(Seismic Piezo-Cone Penetration Test, SCPTu)은 동적 및 정적 물성과 같은 지반의 공학적 특성 평가에 가장 유용한 조사 기법 중의 하나이다. 본 연구에서는 국내 지반에 대한 실질적 활용 연구로서, 국내 대표적 퇴적 지층 발달 지역인 부산과 인천을 대상으로 각각 두 부지와 네 부지에서 SCPTu를 수행하였다. 현장에서 SCPTu로부터 획득한 파형 신호에 대해 교차법을 이용한 신호 판독을 실시하여 깊이별 전단파의 초기 도달 시점 및 그에 따른 깊이별 도달 시차를 결정하였다. 이를 토대로 Snell의 법칙에 근간한 굴절 전파 경로법을 이용하여 전단파 속도$(V_S)$의 깊이별 분포를 도출하였다. 결정된 깊이별 $V_S$ 분포를 콘 선단 저항력$(q_t)$과 비교해 본 결과, 깊이에 따른 두 값의 경향이 유사하게 나타났다. 일반적인 CPTu 자료의 지진공학적 활용을 목적으로 SCPTu로부터 측정된 결과를 토대로 $V_S$와 콘 관입 특성값의 상관관계를 분석 도출하였다. 다중 회귀 분석을 수행하여 전단파 속도와 콘 관입 특성값 중 네 가지의 독립변수인 콘 관입 저항력$(q_t)$, 주면 마찰력$(f_s)$, 유효상재응력$(\sigma'_{v0})$ 및 간극수압계수$(B_q)$ 간의 상호 관련성을 정량적으로 평가하였으며, 특히 흙 분류 지수인 $I_c$값에 의하여 객관적으로 구분된 사질토 및 점토와 전체 토사에 대한 변수별 경험적 상관식을 제안하였다. SCPTu의 하향식 탄성파 시험과 일반적인 CPTu의 대상 변형률 수준이 다름에도 불구하고 본 연구에서 도출 제안된 $V_S$와 CPTu 특성값의 상관관계는 국내 일부 퇴적 지반에 대한 $V_S$의 예비적 평가에 매우 유용하였으며, 기존 해외 연구의 상관관계에 비해서도 높은 상관성을 보였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.