• Geomechanics and Engineering
• /
• 제12권3호
• /
• pp.361-397
• /
• 2017

The unloading effect from excavations can cause the deformation of adjacent tunnels, which may seriously influence the operation and safety of those tunnels. However, systematic studies of the deformation characteristics of tunnels located along side excavations are limited, and simplified methods to predict the influence of excavations on tunnels are also rare. In this study, the simulation capability of a finite element method (FEM) considering the small-strain characteristics of soil was verified using a case study. Then, a large number of FEM simulations examining the influence of excavations on adjacent tunnels were conducted. Based on the simulation results, the deformation characteristics of tunnels at different positions and under four deformation modes of the retaining structure were analyzed. The results indicate that the deformation mode of the retaining structure has a significant influence on the deformation of certain tunnels. When the deformation magnitudes of the retaining structures are the same, the influence degree of the excavation on the tunnel increased in this order: from cantilever type to convex type to composite type to kick-in type. In practical projects, the deformation mode of the retaining structure should be optimized according to the tunnel position, and kick-in deformation should be avoided. Furthermore, two methods to predict the influence of excavations on adjacent tunnels are proposed. Design charts, in terms of normalized tunnel deformation contours, can be used to quantitatively estimate the tunnel deformation. The design table of the excavation influence zones can be applied to determine which influence zone the tunnel is located in.

• Composites Research
• /
• 제30권1호
• /
• pp.52-58
• /
• 2017

본 논문에서 제시한 복합재 날개 구조물의 최적설계 기법은 파손모드를 통합한 최적화 프레임 웍을 사용하여 복합재 날개 구조물의 안전율을 자동으로 계산한다. 개발된 최적화 프레임 웍은 복합재 구조물의 설계요소에 가장 큰 영향을 주는 파손모드 즉, 최초 파손모드, 좌굴 파손 모드 및 베어링-바이패스 파손을 확인하여 구축된 적층 데이터베이스 안에서 적층수를 찾아낸다. 이는 개발과정에서 수정 및 반복되는 설계 및 해석 시간을 단축시킬 수 있는 효과가 있다. 설계변수는 계단형태로 이루어진 적층 데이터베이스이며 응답은 변형률, 좌굴, 볼트 주변부의 응력장이며 목적함수는 날개구조의 질량이다. 그리고 최적화 프레임 윅을 구동하는 Composite Optimizer의 해석결과를 검증하기 위하여 유한요소모델의 좌굴해석 결과와 비교하여 유효성을 검증하였다.

• Steel and Composite Structures
• /
• 제26권6호
• /
• pp.793-808
• /
• 2018

In this study, the seismic performance of the connections between L-shaped columns composed of concrete-filled steel tubes (L-CFST columns) and H-beams used in high-rise steel frame structures was investigated. Seven full-scale specimens were tested under quasi-static cyclic loading. The variables studied in the tests included the joint type, the axial compression ratio, the presence of concrete, the width-to-thickness ratio and the internal extension length of the side plates. The hysteretic response, strength degradation, stiffness degradation, ductility, plastic rotation capacity, energy dissipation capacity and the strain distribution were evaluated at different load cycles. The test results indicated that both the corner and exterior joint specimens failed due to local buckling and crack within the beam flange adjacent to the end of the side plates. However, the failure modes of the interior joint specimens primarily included local buckling and crack at the end plates and curved corners of the beam flange. A design method was proposed for the flexural capacity of the end plate connection in the interior joint. Good agreement was observed between the theoretical and test results of both the yield and ultimate flexural capacity of the end plate connection.

• 한국강구조학회 논문집
• /
• 제19권1호
• /
• pp.43-52
• /
• 2007

CFT(Concrete Filled Steel Tube, 콘크리트 충전 강관) 부재는 뛰어난 구조거동으로 인하여 그 사용 영역이 점차 확대되고 있는 추세이나, 대단면의 부재로 사용될 경우에는 자중과 경제성에서 불리할 수 있다. 본 연구에서는 CFT 부재의 단면을 중공으로 만듦으로써, 콘크리트 사용량을 절감하여 부재의 자중을 감소시키고, 중공면에 강관 또는 FRP 튜브를 삽입하여 성능을 향상시킨 내부 구속 중공 CFT 부재의 합리적인 해석을 위하여 비선형 콘크리트 모델을 개발하였다. 개발된 비선형 콘크리트 모델은 구속효과를 고려한 Mander의 일축 압축 콘크리트 모델을 기본으로 하였으며, 내부 구속 중공 CFT 부재 내 콘크리트의 응력-변형율 선도를 결정하기 위해서, 내부 구속 중공 CFT 부재의 발생 가능한 파괴 형상을 제시하고, 각각의 파괴 형상이 발생할 때의 구속응력을 평형방정식을 통하여 유도하였다. 유도된 식을 통하여, 컴퓨터를 이용한 해석 프로그램이 작성되었으며, 매개변수 연구가 수행되었다. 해석결과, 내부 구속된 콘크리트는 비구속 상태 또는 이축 구속 상태의 콘크리트에 비하여, 향상된 강도와 연성을 갖는다는 것을 확인하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.572-578
• /
• 2003

The free vibration of a spinning flexible disk-spindle system supported by hydro dynamic bearings in a HDD is analyzed by FEM. The spinning flexible disk is described using Kirchhoff plate theory and von Karman non-linear strain, and its rigid body motion is also considered. It is discretized by annular sector element. The rotating spindle which includes the clamp, hub, permanent magnet and yoke, is modeled by Timoshenko beam including the gyroscopic effect. The flexible supporting structure with a complex shape which includes stator core, housing, base plate, sleeve and thrust pad is modeled by using a 4-node tetrahedron element with rotational degrees of freedom to satisfy the geometric compatibility. The dynamic coefficients of HDB are calculated from the HDB analysis program, which solves the perturbed Raynolds equation using FEM. Introducing the virtual nodes and the rigid link constraints defined in the center of HDB, beam elements of the shaft are connected to the solid elements of the sleeve and thrust pad through the spring and damper element. The global matrix equation obtained by assembling the finite element equations of each substructure is transformed to the state-space matrix-vector equation, and the associated eigenvalue problem is solved by using the restarted Arnoldi iteration method. The validity of this research is verified by comparing the numerical results of the natural frequencies with the experimental ones. Also the effect of supporting structures to the natural modes of the total HDD system is rigorously analyzed.

• 한국재료학회지
• /
• 제16권4호
• /
• pp.241-247
• /
• 2006

Structural studies have been performed on precipitation hardening discovered in $L1_2-ordered\;Ni_3(Al,Cr)$ containing 0.2 to 3.0 mol% of carbon using transmission electron microscopy (TEM). Fine octahedral precipitates of $M_{23}C_6$ appeared in the matrix by aging at temperatures around 973 K after solution treatment at 1423 K. TEM examination revealed that the $M_{23}C_6$ phase and the matrix lattices have a cube-cube orientation relationship and keep partial atomic matching at the {111} interface. After prolonged aging or by aging at higher temperatures, the $M_{23}C_6$ precipitates then adopt a rod-like morphology elongated parallel to the <100> directions. Deformation at temperature below 973 K, typical Orowan loops were observed surrounding the $M_{23}C_6$ particles. At higher deformation temperatures, the Orowan loops disappeared and the morphology of dislocations at the particle-matrix interfaces suggested the existence of attractive interaction between dislocations and particles. The change of the interaction modes between dislocation and particles with increasing deformation temperature can be considered as a result of strain relaxation at the interface between matrix and particles.

• 한국농공학회지
• /
• 제40권5호
• /
• pp.68-79
• /
• 1998

In the years, the concern about high-strength concrete which is new material has been heightened as a result of active research and development. Recently, as the building structure has been being bigger, higher, longer and more specialized, the demand of material with high-strength concrete for building has been increasing. The demand of high -strength concrete is expected to increase with expansion of usage about the complex concrete structures such as bridge structure as well as nuclear plants, underground structures, hydraulic structures and arctic area sturctures. In this research, silica-fume was used as an admixture in order to get a high-strength concrete. Water/binder ration was limited no more than 18 percent and the amount of unit cement was increased. In this study, a number of trial in concrete mix was carried out to get optimal mix design, and the target slump with $10{\pm}2cm$ was set for in-situ construction. High-strength concrete with cylinder strength of 1,200kgf/$cm^2$ in the 28-days was produced and tested. The static test was carried out to measure the ultimate load, the initial load of flexural and diagonal cracking, crack patterns, fracture modes. The load versus strain and load versus deflection relations were obtained form the static test. The test results were compared with the shear strengths predicted by the equations of ACI code 318-89 and orther researchers. Based on the test results, shear strength equation of reinforced concrete beam using high strength concrete was proposed. Form an evaluation of the results of this experimental investigation, it was concluded that shear strength after diagonal tention cracking diminished with the increase in compressive strength for beams.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권3호
• /
• pp.119-126
• /
• 2008

국내에서 공동주택이 대량으로 공급되었던 1980~1990년대에는 콘크리트의 설계기준강도가 약 18MPa로 낮았으며 또한 대부분의 기둥은 수직하중만을 고려하여 설계되었다. 본 연구에서는 수명이 오래된 콘크리트 기둥의 성능을 향상시키기 위하여 시공이 간편하고 내식성이 우수하며 인장성능이 매우 뛰어난 탄소섬유시트로 보강된 RC 기둥의 압축강도 성능평가 실험을 수행하였다. 기둥을 구속하는 탄소섬유시트의 wrapping 각도는 수직하중과 수평하중에 저항할 수 있도록 기둥의 재축방향에 대하여 ${\pm}60^{\circ}$ 각도로 보강하였다. 실험을 수행한 후 압축강도 및 변형률의 증가양상과 시험체의 파괴양상을 분석하였으며 실험결과의 회귀분석을 수행하여 향상된 압축강도를 예측할 수 있는 회귀식을 작성하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권3호
• /
• pp.93-100
• /
• 2008

혹독한 자연환경하에서의 구조물의 내구성이 주요한 관심사도 대두되면서 건설분야에서 섬유강화폴리머의 사용이 점차 증가하고 있는 추세이다. 본 연구에서는 FRP bar를 휨부재의 휨보강근으로서의 적용가능성을 평가하기 위하여 휨실험을 수행하였다. 탄소섬유, 유리섬유 및 탄소와 유리섬유를 혼합한 hybrid 섬유 보강근을 사용하여 보강량을 변화시킨 12개의 실험체를 제작하여 실험을 수행하였으며, 그결과는 파괴형태, 모멘트-변위, 휨강도, 연성지수 및 단면에서의 변형율분포 등에 대하여 분석하였다. 실험결과는 ACI 기준에 제시된 모델과 비교하였으며, 전체적으로 보의 휨강도는 강도설계이론에 의한 결과와 거의 유사한 것으로 나타났다. 그러나 처짐의 경우에는 유리섬유의 경우는 이론이 과대평가 되었으며, 탄소섬유는 과소평가되는 것으로 나타났다.

• Steel and Composite Structures
• /
• 제19권5호
• /
• pp.1095-1113
• /
• 2015

In order to determine the mechanical behavior of the curved laminates in practical applications, three right-angled composite brackets with different lay-ups were investigated both experimentally and numerically. In the experimental, quasi-static tests on both unidirectional and multidirectional curved composite brackets were conducted to study the progressive failure and failure modes of the curved laminates. In the numerical modeling, three-dimensional finite element analysis was used to simulate the mechanical behavior of the laminates. Here, a strength-based failure criterion, namely the Ye criterion, was used to predict the delamination failure in the composite curved laminates. The mechanical responses of the laminate subjected to off-axis tensile loading were analyzed, which include the progressive failure, the failure locations, the load-displacement relationships, the load-strain relationships, and the stress distribution around the curved region of the angled bracket. Subsequently, the effects of stacking sequence and thickness on the load carrying capacity and the stiffness of the laminates were discussed in detail. Through the experimental observation and analysis, it was found that the failure mode of all the specimens is delamination, which is initiated abruptly and develops unstably on the symmetric plane, close to the inner surface, and about $29^{\circ}$ along the circumferential direction. It was also found that the stacking sequence and the thickness have significant influences on both the load carrying capacity and the stiffness of the laminates. However, the thickness effect is less than that on the curved aluminum plate.