• 한국강구조학회 논문집
• /
• 제10권2호통권35호
• /
• pp.303-315
• /
• 1998

크레인 주행거더에 발생된 피로균열에 대한 보수방법으로 stop-hole(5mm 또는 9mm), stop-hole에 고력볼트 체결, 용접. 첨판과 고력볼트에 의한 4가지 보수방법을 적용하였다. 이중에서 stop-hole로 보수를 한 경우와 용접보수를 한 경우에는 재균열이 발생하였다. 그러나 stop-hole에 고력볼트를 체결한 경우 및 첨판과 고력볼트로 보수한 경우에는 재균열이 발생하지 않았다. 보수전과 보수후 피로강도를 비교해보면 stop-hole 또는 stop-hole과 고력볼트로 보수를 한 경우에는 모두 보수전과 동등한 피로강도를 얻었다. 용접보수를 할 경우에는 정확한 시공이 시행되면 보수전과 동등한 피로강도를 기대할 수 있지만. 시공이 잘못되면 피로강도가 현저하게 저하될 수 있음을 알 수 있었다. 피로균열이 발생된 위치에 첨판과 소요볼트를 시공할 수 있는 조건이라면 첨판과 고력볼트로 보수하는 것이 가장 확실한 보수법임을 알 수 있었다.

• 대한토목학회논문집
• /
• 제7권4호
• /
• pp.115-124
• /
• 1987

본 연구는 피로균열이 발생한 부재의 응급적인 보수, 보강방법으로 예로부터 실제로 이용되어 온 stop-hole에 대하여 그 보수, 보강효과를 잔존수명의 관점에서 정량적인 평가를 시도한 것이다. 이를 위하여 대상 시험편에 대한 피로시험을 실시하여 그 피로거동을 검토한 결과, 피로균열에 대한 응급조치로서 stop-hole을 이용할 경우, 균열이 탄소성 거동을 하는 영역에 이르기 전에 처리하는 것이 바람직함을 알 수 있었다.

• Steel and Composite Structures
• /
• 제2권6호
• /
• pp.475-488
• /
• 2002

In steel bridges fatigue cracks are sometimes repaired by placing drilled holes at the crack tips. From the meaning that the drilled holes stop the propagation of cracks, they are called stop-holes. Since stop-holes are regarded as an emergency measure to delay crack propagation, usually some substantial repair follows. However, if the stress at the stop-holes is below their fatigue limit, fatigue cracks would not be expected to occur. The purpose of this study is to present the conditions under which stop-holes prevent the reinitiation of fatigue cracks. The fatigue limit of stop-holes and the equations necessary to estimate the maximum stress on the circumference of the stop-holes are provided.

• Structural Monitoring and Maintenance
• /
• 제6권4호
• /
• pp.291-315
• /
• 2019

Fatigue cracks are inevitable in circumstances in which the cyclic loading exists. Therefore, many of mechanical components are in a risk of being in exposure to fatigue cracks. On the other hand, renewing the facilities or infrastructures is not always possible. Therefore, retrofitting the structures by means of the available methods, such as crack arrest methods is logical and in some cases inevitable. In this regard, this paper considers three popular crack arrest methods (e.g., drilling stop-hole, steel welded patch, and carbon fiber reinforced (CFRP) patch), which have been compared by using extended finite element method (XFEM). In addition, effects in terms of the width and thickness of patches and the configuration of drilling stop holes have been evaluated. Test results indicated that among the considered methods, CFRP patches were the most effective means for arresting cracks. Besides, in the case of arresting by means of drilling stop holes, drilling two holes next to the crack-tip was more effective than blunting the crack-tip by drilling one hole. In other words, the results indicated that the use of symmetric welded metal patches could lead to a 21% increase in fatigue life, as compared to symmetric stop holes. Symmetric CFRP patches enhanced the fatigue life of cracked specimen up to 77%, as compared to drilling symmetric stop holes. In addition, in all cases, symmetric configurations were far better than asymmetric ones.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.204-213
• /
• 2001

This paper develops the compliance approach to the problem of load sharing between a cracked plate and a cover plate used to bridge the crack. The theory is validated by using calculated stress intensity factors for the covered and uncovered cases and by using stop hole method to reduce experimentally observed growth rates to a common base. Calculations are then made on the effect of cover plate width on fatigue crack retardation in order to demonstrate the predictive capability of the technique.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 센서 박막재료 반도체재료 기술교육
• /
• pp.12-15
• /
• 2002

In this paper, we fabricated a electro-chemical discharge machine for drilling microscopic glass hole. In this research, we used a glass plate and NaOH solution. From the experimental result, we knew that the change of voltage wave was caused by drilling microscopic hole of glass using electro-chemical discharge method. So, we can give a function of the power auto stop to electro-chemical discharge machine with the change of voltage wave.

• 한국안전학회지
• /
• 제25권1호
• /
• pp.65-71
• /
• 2010

In this study, a series of finite element analysis using LUSAS were performed in order to assess the quantitative effects of repair and retrofit of stringer in steel plate girder railway bridge with fatigue cracks. And cutoff types of end part of upper flange were considered as right-angled type and round-angled type. Also, as a method of repair and retrofit of fatigue cracks in stringer, perforation of stop-hole and installation of bracket were considered. From the analysis result, it was possible to assess the fatigue safety and fatigue life of stringer with fatigue cracks, and to estimate the stress intensity factor range in cut-off part of stringer using J-integral method. Also, according to the method of perforation of stop-hole and installation of bracket, it was possible to calculate the crack propagation life at the cut-off part of stringer.

• 한국강구조학회 논문집
• /
• 제9권3호통권32호
• /
• pp.363-375
• /
• 1997

절취된 세로보를 갖는 강철도교량의 바닥판에서의 피로거동 및 손상시 보수 보강의 효과를 연구하기 위해 8개 대형시험체에 대한 모형시험을 수행하였다. 실교량을 대상으로 실동응력을 측정하여 기본 응력범위 빈도히스토그램을 작성하고 이에 의한 변동응력의 등가응력범위를 산출하였다. 이 등가응력범위를 기준으로 피로시험의 응력변동범위의 크기를 조정하면서 정적 및 피로시험을 보강전과 보수 보강후로 구분하여 실시하였다. 정적시험에 의하면 재하하중의 크기가 등가실동응력 수준인 시험체의 경우에서 이미 허용응력과 비슷한 응력을 나타내므로서 피로균열의 발생조건을 충족하고 있었다. 손상된 시험체에 대해 다양한 보수 및 보강을 실시하여, 각각의 결과를 비교검토하였다. 그 결과 보수효과는 stop hole을 천공하고 고장력볼트를 체결한 경우에 피로균열성장의 지체효과가 뚜렷하게 나타났다. 한편 보강효과는 휨의 지배를 받는 세로보의 경우 인장측 플랜지의 보강이 효과적이며, 복부의 보강은 보강방법으로 적절하지 않음을 알 수 있었다. 또한 직각절취된 세로보의 피로설계등급은 우리나라 시방서 피로설계규정의 E등급에 해당한다는 것을 확인할 수 있었다.

• 한국공작기계학회논문집
• /
• 제11권2호
• /
• pp.103-111
• /
• 2002

Out of all metal-cutting process, the hole-making process is the most widely used. It is estimated to be more than 30% of the total metal-cutting process. It is therefore desirable to monitor and detect drill wear during the hole-drilling process. One important aspect in controlling the drilling process is monitoring drill wear status. There are two systems, Basic system and Online system, to detect the drill wear. Basic system comprised of spindle rotational speed, feed rates, thrust torque and flank wear measured by tool microscope. Outline system comprised of spindle rotational speed feed rates, AE signal, flank wear area measured by computer vision, On-line monitoring system does not need to stop the process to inspect drill wear. Backpropagation neural networks (BPNs) were used for on-line detection of drill wear. The output was the drill wear state which was either usable or failure. This paper deals with an on-line drill wear monitoring system to fit the detection of the abnormal tool state.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.821-826
• /
• 2001

Out of all metal-cutting processes, the hole-making process is the most widely used. It is estimated to be more than 30% of the total metal-cutting process. It is therefore desirable to monitor and detect drill wear during the hole-drilling process. One important aspect in controlling the drilling process is monitoring drill wear status. Accordingly, this paper deals with Basic system and Online system. Basic system comprised of spindle rotational speed, feed rates, thrust, torque and flank wear measured tool microscope. Online system comprised of spindle rotational speed, feed rates, AE signal, flank wear area measured computer vision. On-line monitoring system does not need to stop the process to inspect drill wear. Backpropagation neural networks (BPNs) were used for on-line detection of drill wear. This paper deals with an on-line drill wear monitoring system to fit the detection of the abnormal tool state.