• Journal of the Korea Concrete Institute
• /
• v.12 no.2
• /
• pp.99-107
• /
• 2000

This research investigates experimentally an effect on the properties of the high flowing concrete to be poured in the under-ground slurry wall of Inchon LNG receiving terminal(#213,214-TK) according to variations of concrete materials. Variables for sensitivity test were selected items as followings. 1) Concrete temperature (3cases), 2) Unit water (5cases), 3) Fineness modulus of fine aggregate (5cases), 4) Particle size of lime stone powder (3cases), 5) Replacement ratio of blast-furnace slag (4cases) and 6) Addition ratio of high range water reducing agent (5cases). And fresh conditions of the super flowing concrete should be satisfied with required range including slump flow(65$\pm$5cm), 50cm reaching time of flow(4~10sec), V-lot flowing time(10~ 20sec), U-box height(min. 300mm) and air content(4$\pm$1%). As results for sensitivity test, considered flow-ability, self-compaction and segregation resistance of the high flowing concrete, material variations and conditions of fresh concrete should be satisfied with the range as follwings. 1) Concrete temperature are 10~2$0^{\circ}C$(below 3$0^{\circ}C$), 2) Surface moisture of fine aggregate is within $\pm$ 0.6%, 3) Fineness modulus of fine aggregate is 2.6$\pm$0.2, 4)Replacement ratio of blast-furnace slag is 45~50% and 5) Addition ratio of high range water reducing agent is within 1%. Based on the specification for quality control, we successfully finished concrete pouring on the under-ground slurry wall having 75,000㎥(#213,214-TK) and accumulated real date in site.

• Journal of Technologic Dentistry
• /
• v.35 no.1
• /
• pp.57-64
• /
• 2013

Purpose: Waste parts of zirconia blocks and powders were remained after CAD/CAM process. In order to make these residual zirconia fit for practical use, zirconia single cores were produced by drain casting process. Methods: Remained zirconia blocks were reduced to powders with zirconia mortar, and screened with 180 mesh sieve. Zirconia slip was prepared from waste parts of zirconia by ball milling. Plaster molds for forming cores by slip casting were also prepared. Formed cores were removed from mold after partial drying. Dried cores were biscuit fired at $1,100^{\circ}C$ for 1hour. Biscuit fired cores were treated with tools to control the fitness and thickness. Finished cores were $2^{nd}$ fired at $1,500^{\circ}C$ for 1hour. Microstructure of cross section of core was observed by SEM. Results: When mill pot was filled with 100g of zirconia and alumina mixed powder, 300g of zirconia ball, and 180g of distilled water, the optimum slip for drain casting was obtained. Gypsum plaster for ceramic forming was more suitable then yellow stone plaster for casting process. SEM photograph showed the microstructure of fully dense with uniform grain size of zirconia and well dispersed alumina grains into the zirconia matrix. Conclusion: Zirconia single cores were produced by drain casting process. Drain casting is useful process to make these residual zirconia fit for practical use. Further study will be focused on the preparation of the bridge type cores by casting.

• Journal of the Korean housing association
• /
• v.6 no.2
• /
• pp.181-189
• /
• 1995

It is thought as more important for us to understand foreign countrie's culture in the modern society. because the world is becoming closer day by day thiough the develepment of communication and mass-media. Cross-cultural study could play a role to give an opportunity for people to understand foreign countrie’s culture easily.In this respect, this study was planned to find out similarity and difference between Danish and Korean folk tables made and used before the 20th century during the 18th-l9th century as a part of the comparative study of folk furniture between the two countries. It would be very interesting if we could find something valuable between Danish and Korean folk furniture. because they are located very far away each other geographically with less cultural communication before.There were more differences than similarity between the folk tables of the two countries and major findings were as followings : Firstly, there were many kinds of space-saving tables in Denmark. whereas only a few kinds of tables which could be removed easily after their usage were found in KoreaSecondly, Banish folk tables were more emphasized on the function rather than decoration. Whereas Korean folk tables were smaller lower and more decorative than Danish ones to fit their life-style of sitting on the floor.Thirdly, many Danish folk tables were made of bare wood. while Korean ones were finished by transparent lacquer or vegetable oil. Stone tops if tables were rare in both countries. Lastly. there were common factors in the design of legs of folk tables in both countries. It was interesting that animal legs such as deg tiger cat. lion, and eagle were used for design motif of the table legs. But trestle leg, cross leg and gate leg were not found in Korean folk tables. As a conclusion, throughout this study, it became obvious that life-style was one of the most important factor influencing on the design of furniture.

• The Journal of Korean Academy of Prosthodontics
• /
• v.35 no.4
• /
• pp.719-741
• /
• 1997

This study was undertaken to compare by Atomic Force Microscope the effects of various finishing and polishing instruments on surface roughness of filling and veneering composite resins. Seven composite resins were studied : Silux Plus (3M Dental Products, U.S.A.), Charisma (Heraeus Kulzer, Germany), Prisma THP (L.D.Caulk, Dentsply, U.S.A.), Photoclearfil (Kuraray, Japan), Cesead (Kuraray, Japan), Thermoresin LC (GC, Japan), Artglass (Heraeus Kulzer, Germany). Samples were placed and polymerized in holes (2mm thick and 8.5mm in diameter) machined in Teflon mold under glass plate, ensuring excess of material and moulded to shape with polyester matrix strip. Except control group (Polyester matrix strip), all experimental groups were finished and polishied under manufacturer's instructions. The finishing and polishing procedure were : carbide bur (E.T carbide set 4159, Komet, Germany), diamond bur (composite resin polishing bur set, GC, Japan), aluminum-oxide disc (Sof-Lex Pop-On, 3M Dental Products, U.S.A.), diamond-particle disc (Dia-Finish, Renfert Germany), white stone bur & rubber point( composite finishing kit, EDENTA, Swiss), respectively. Each specimens were evaluated for the surface roughness with Atomic Force Microscope (AutoProbe CP, Park Scientific Instruments, U.S.A.) under contact mode and constant height mode. The results as follows : 1. Except Thermoresin LC, all experimental composite resin groups showed more rougher than control group after finishing and polishing(p<0.1). 2. A surface as smooth as control group was obtained by $Al_{2}O_{3}$ disc all filling composite resin groups except Charisma and all veneering composite resin groups except Thermoresin LC(p<0.05). 3. In case of Thermoresin LC, there were no statistically significant differences before and after finishing and polishing(p>0.1). 4. Carbide bur, diamond bur showed rough surfaces in all composite resin groups, so these were inappropriate for the final polishing instruments.

• The Journal of Advanced Prosthodontics
• /
• v.5 no.2
• /
• pp.179-186
• /
• 2013

PURPOSE. One of the most important factors in evaluating the quality of fixed dental prostheses (FDPs) is their gap. The purpose of this study was to compare the marginal and internal gap of two different metal-ceramic crowns, casting and selective laser sintering (SLS), before and after porcelain firing. Furthermore, this study evaluated whether metal-ceramic crowns made using the SLS have the same clinical acceptability as crowns made by the traditional casting. MATERIALS AND METHODS. The 10 study models were produced using stone. The 20 specimens were produced using the casting and the SLS methods; 10 samples were made in each group. After the core gap measurements, 10 metal-ceramic crowns in each group were finished using the conventional technique of firing porcelain. The gap of the metal-ceramic crowns was measured. The marginal and internal gaps were measured by two-dimensional and three-dimensional replica techniques, respectively. The Wilcoxon signed-rank test, the Wilcoxon rank-sum test and nonparametric ANCOVA were used for statistical analysis (${\alpha}$=.05). RESULTS. In both groups, the gap increased after completion of the metal-ceramic crown compared to the core. In all measured areas, the gap of the metal cores and metal-ceramic crowns produced by the SLS was greater than that of the metal cores and metal-ceramic crowns produced using the casting. Statistically significant differences were found between cast and SLS (metal cores and metal-ceramic crown). CONCLUSION. Although the gap of the FDPs produced by the SLS was greater than that of the FDPs produced by the conventional casting in all measured areas, none exceeded the clinically acceptable range.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.4
• /
• pp.170-187
• /
• 2020

Dolmens bearing the burial layout and stone coffin tombs of the late Bronze Age were excavated from Samdeok-ri, Goseong, Gyeonsangnsamdo, and grave items such as red-burnished pottery, arrowheads, and stone swords were also discovered. In the case of the red-burnished pottery that was found, it retains a pigment layer with a thickness of about 50 to 160㎛, but with most of the other items, exfoliation and peeling-off of pigment layers can be observed on the surface. The raw materials of the red-burnished pottery contained moderately sorted minerals such as quartz, feldspar, and hornblende, and partly opaque iron oxide minerals were also identified. In particular, the raw materials of the red-burnished pottery from stone coffin tomb #6 were different from those of the other pottery, containing large amounts of hornblende and feldspar. The pottery's red pigment was identified as hematite and showed similar mineral content of raw materials such as fine grained quartz, feldspar, and hornblende. The firing temperature is estimated to have been approximately 900℃, based on their mineral phase. The possibility exists that the raw materials had been collected from the Samdeok-ri area, because diorite and granite diorite with dominant feldspar and hornblende have been identified within 3km of that area. During the pottery manufacturing process, it is estimated that the pigment was painted on the entire surface of the red-burnished pottery after it had been molded and then finished using the abrasion technique. In other words, the red-burnished pottery was made by the process of vessel forming - semi drying - coloring - polishing. The surface and cross-section of the pottery appears differently depending on the concentration of the pigment and the coloring method used after vessels were formed. Most of the excavated pottery features a distinct boundary between pigment and body fabric. However, in the case of pottery in which fine-grained pigments penetrate the body fabric so that layers cannot be distinguished, there is the possibility that the fine-grained pigment layer was applied at a low concentration or immediately after vessel forming. Many cracks can be seen on the surface pigments in thickly painted pottery items, and in many cases, only a small portion of the pigment layers remain due to surface exfoliation and abrasion in the burial environment. It is reported that pottery items may be more easily damaged by abrasion if coated with pigment and polished, so it is believed that the red-burnished pottery of the Samdeok-ri site suffered from weathering in the burial environment. This damage was more extensive in the potsherds that were scattered outside the tomb.

• KOMUNHWA
• /
• no.70
• /
• pp.63-88
• /
• 2007

The purpose of this writing is to examine the places and instruments of the dissection for deformed animal carcasses excavated in shellfish stacks of the period of the Proto-Three Kingdoms(삼한) and the Three Kingdoms(삼국). The remains were chosen, which had been excavated and finished in the analysis of the animal carcasses, and the main objects are all shells and deer, especially among Mammalia. As the result, the dissection of shells was not taken place in the habitats of the animals, but inside or around of the residence of the people. For deer, too, it was done in the public place or specific area around and inside the residence. As concerns the method of dissection for shells, for Pelecypoda(부족류), represented by Meretrix lusoria(백합), the inner meat was taken out by wrenching the shell with a kind of small knives, or by boiling, and sometimes by cracking the middle of the shell in the case of big Meretrix lusoria and Dosinorbis japonicus(떡조개). For Rapana venosa(피뿔고둥), representative of Gastropoad(배발류), the people broke the top or some parts of the body to get the inner meat or used some kind of needles and stylus to pick the inner meat out after boiling. Abalones‘ meat was attached firmly to the shell, so very sharp and proper metal instruments were used to take the meat out Relatively small-sized Reishia clavigera(대수리),Top shell(밤고둥) meats were taken out by breaking the top parts after boiling, then sucking the meats, or by picking them out by using needles and stylus in the original shape. In the case of large Mammalia like deer, in the full consideration of the point that deer itself are used in various ways, they were dissected in the order of skinning, taking out the internal organs, cutting front and rear legs, separating joint parts and meats, extracting bone-marrow by 철정, 철부, ironed hand knife in very delicate ways. It seems that skinning, and front and rear legs' cutting were taken place in the place around the residence, on the other hand joint parts' separating and bone-marrow extracting in the residence. The tools for the dissection were confirmed to be hand-knife, honed ax, hammer stone, bondstone, needles and stylus, and some other sharp instrument. They were used properly according to objects.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.44 no.3
• /
• pp.25-36
• /
• 2016

As the first public park in Korea, birth place of the march first independence movement, and a representative space of leisure of old men, Tapgol Park contains diverse symbolisms and meanings. In 2000, Seoul authorities selected the symbolism of the March First independence movement, and carried forward the sacralization project of Tapgol Park. They eliminated facilities, including vending machines, and restricted most of the leisure activities in the park such as drinking singing dancing, speech, playing chess, writing calligraphy, etc., and loitering. Also, they changed the park's design into a less available space with green areas and switched wooden benches to granite stone. Since the project finished, a representative phenomenon was the elderly men's exodus to Jongmyo Park, where the restrictions were not strong as in Tapgol Park. As a result, the numbers of users in Tapgol Park decreased sharply. However, overcrowded(more than 3000) Jongmyo Park is also in the middle of a sacralization project now. According to an investigation including observation and in-depth interview, most of the elderly men who use the parks almost everyday were in the low economic class. They just visit the parks everyday and chat with their peers, gaining comfort from each other. These phenomena can be interpreted as a social exclusion in society, which made the elderly men move to another place. Meanwhile, although fifteen years has passed since the project was completed, many people still regard the Tapgol Park as a place for elderly men instead of the birth place of the March First Independence Movement. This study focused on such problems and vague place identity, which is neither a memorial place nor a public park. The study discovery the fact they missed the symbolism that Tapgol Park was the first urban park of Korea. Also, it stresses that the monumentality does not need to be sacred, reverent, or inflexible. With this point of view, this study discussed public aspect and everydayness, which are included in most of the urban parks. Finally, this study suggests Tapgol Park as an urban park that has an identity that embraces the condition of monumentality, everydayness, and publicness all together.