• Geomechanics and Engineering
• /
• 제32권4호
• /
• pp.375-385
• /
• 2023

There are many joint fissures distributed in the engineering rock mass. In the process of geological history, the underground rock mass undergoes strong geological processes, and undergoes complex geological processes such as fracture breeding, expansion, recementation, and re-expansion. In this paper, the damage-stick-slip process (DSSP), an analysis model used for rock mass failure slip, was established to examine the master control and time-dependent mechanical properties of the new and primary fractures of a multi-fractured rock mass under the action of stress loading. The experimental system for the recemented multi-fractured rock mass was developed to validate the above theory. First, a rock mass failure test was conducted. Then, the failure stress state was kept constant, and the fractured rock mass was grouted and cemented. A secondary loading was applied until the grouted mass reached the intended strength to investigate the bearing capacity of the recemented multi-fractured rock mass, and an acoustic emission (AE) system was used to monitor AE events and the update of damage energy. The results show that the initial fracture angle and direction had a significant effect on the re-failure process of the cement rock mass; Compared with the monitoring results of the acoustic emission (AE) measurements, the master control surface, key blocks and other control factors in the multi-fractured rock mass were obtained; The triangular shaped block in rock mass plays an important role in the stress and displacement change of multi-fracture rock mass and the long fissure and the fractures with close fracture tip are easier to activate, and the position where the longer fractures intersect with the smaller fractures is easier to generate new fractures. The results are of great significance to a multi-block structure, which affects the safety of underground coal mining.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2000년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 2000
• /
• pp.33-40
• /
• 2000

The assessment of earthquake hazards involved consideration of earthquake magnitude, frequency, last movement and probability of occurrence. The appraisal of earthquake potential is feasible because historical data show a good correlation between earthquake size and the fault rupture parameters of length, displacement, and area. Additionally, the characteristics of fault behavior should be considered to evaluate the earthquake potential magnitude. In this study, in order to evaluate the earth quake potential by the fault behavioral patterns, based on the experimental background which the geometric characteristics of the individual domains, such as strike, width, fault tip patterns, and orientation of secondary shears reflect sliding behavioral patterns in each section, the straight sections of A, D and E domains were examined to the creeping section of stably sliding. In contrast, the curved section of B domain was examined to the locked section of stick-slip movement. These results of studies can be applied to evaluate the earthquake potential magnitude from the fault structural parameters.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.442-445
• /
• 2011

Concrete track on the new railway lines of the existing roads are built on high ground, or less than 400m radius of the sharp curve sectors will occur. sharp curve sectors the rail and wheel friction, stick-slip due to the band of 1,000Hz or squeal noise occurs from the increase in civil complaints about noise is a real situation. In this study, discussed in previous studies, noise measurements for each radius of concrete track and frequency analysis, followed by the radius of the curve in order to investigate vibration characteristics of urban railway sector sharp curve radius less than 400m and 400m ~ 1,000 m further to the point selected track components(rails, sleepers, ballast) according to the vibration measurements and analysis of the frequency characteristics and the results were derived.

• 한국철도학회논문집
• /
• 제11권2호
• /
• pp.176-181
• /
• 2008

철도차량의 차륜과 레일 시스템을 모사한 스킬소음 발생장치를 통해 실험을 수행하여 관련 원리를 실험적으로 증명하고 스킬소음 발생 메커니즘에 대한 체계적인 연구를 수행하였다. 이를 위해 스킬소음발생 메커니즘 연구를 소음원-전달계-반응계의 단계별로 진행하였다. 또한 차륜과 레일간의 스틱-슬립 운동에 의한 상대속도 또는 미끄러지는 수준과 마찰결과로서 계산되는 크립곡선과 발생 음압을 시간 및 주파수 영역에서 관찰하여 스킬 소음이 발생하는 조건을 살펴보았다.

• International Journal of Automotive Technology
• /
• 제3권4호
• /
• pp.171-176
• /
• 2002

A bench test set-up is employed to simulate the friction characteristics of a paper-based friction material operating against a steel plate. Dry friction tests are run as well as tests with transmission fluids. Glazed friction material produces a negative coefficient of friction versus sliding velocity (f-v) curve for both dry friction and lubrication with transmission fluids. At low sliding speeds, the coefficient of friction when operating in transmission fluids for glazed friction materials is greater than that under dry friction. An appreciable negative f-v slope occurs at low sliding speeds for glazed friction materials when running with the transmission fluid. The friction material after running in produces a constant f-v curve under dry friction and a negative slope when lubricated with transmission fluid. At low sliding speeds, the coefficient of friction of the run-in friction material is lower than that of the glazed wet material. On the other hand, the run-in friction material has a larger friction coefficient than does the glazed friction material at higher sliding speeds.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• 제2권2호
• /
• pp.146-152
• /
• 2002

Mold level control has been a major control task for continuous casting plants. The system involves nonlinearities such as stick-slip friction in the sliding gate, time-delay, friction force variations between molten steel and the inner wall of mold, and nozzle logging/unclogging. These complex problems should be solved to control mold level for steel cast. In this paper, we propose a neural fuzzy mold level control technique for solving these complex problems and give experiment studies to show the mold level control in continuous casting process.

• 대한기계학회논문집
• /
• 제18권8호
• /
• pp.2026-2038
• /
• 1994

A numerical scheme is developed for the analysis of incipient sliding contact with orthotropic friction condition subjected to tangential load and twisting moment. The inherent nonlinearity in the orthotropic friction law has been treated by a polyhedral friction law. Then, a three-dimensional linear complementarity problem(LCP) formulation in an incremental form is obtained, and the existence of a solution is investigated. A Lemke's complementary pivoting algorithm is used for solving the LCP. The scheme is illustrated by spherical contact problems, and the effects of eccentricity of elliptical friction domain on the traction and stick region are discussed.

• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.723-729
• /
• 2013

The contraction and expansion noise of a refrigerator are investigated, and some effective methods are proposed to reduce the level and occurrence frequency of noise. First, the noise of a refrigerator is measured to estimate the frequency spectrum and occurrence frequency of noise. Second, a sound visualization was conducted using an acoustic camera to determine the location of the noise source. From the results, it was observed that the internal part mainly producing noise was the third shelf in the freezer room. A method to estimate the acceleration on the location of the noise source is introduced to analyze the contraction and expansion noise precisely and accommodate experimental convenience. Noise reduction methods such as the replacement of the existing shelf with glass shelves, adoption of rail slides, and increase of roughness on the contact surface of the shelf are proposed and tested.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1648-1651
• /
• 2005

Fretting contact and fretting fatigue are known to occur in mechanical devices which have fasteners subjected to oscillatory tangential load. Theoretical studies on fretting contact have been focussed on simple geometries, such as cylindrical contact problem. Recently, the contact problem of a flat rounded punch has been solved theoretically. The purpose of this paper is to show that the results of finite element analysis for the fretting contact problem are nearly consistent with the theoretical solutions.

• 제어로봇시스템학회논문지
• /
• 제15권11호
• /
• pp.1076-1079
• /
• 2009

This article deals with an optical image stabilizer which moves an image sensor in the direction of cancelling the vibration caused by hand shaking to prevent a photographed image from blurring. The ball-guide way method adopted as a transfer device of the image sensor is easy to be manufactured because of its simple structure and is suitable to minimize the friction between mechanisms, but has weakness of a chance of physical defect such as groove and rising. In case that the movement of the transfer device equipped with the image sensor is blunted because a ball is stuck in defects of guide way, the performance of the image stabilizer falls down drastically. We propose a method to prevent the transfer device from blunting by applying artificial vibration. At this time, the artificial vibration should be designed under consideration of dynamic characteristics and specifications of the system to be discriminated from the vibration caused by hand shaking.