• Bulletin of the Society of Naval Architects of Korea
• /
• v.7 no.1
• /
• pp.1-12
• /
• 1970

The propeller induced pressure fluctuation around a ship's stern is one of the interesting problems from viewpoints of the noise and vibration. Most of the experimental works on the subject employ pressure transducer attached on hull surface near the propeller. In the technique, the measured pressure includes the hydrodynamic pressure transducer attached, if they exit. Hence, the separation of the additional pressure due to vibration from the measured pressure is essential for the determination of true values of the propeller induced pressure. In this paper, to contribute to the separation method, the author investigated the additional hydrodynamic pressure as below, based on the numerical calculation. (1) Hydrodynamic pressure on the body surface of two dimensional cylinders of some mathematical sections such as ellipse, rectangle, Lewis form of hypotrocoidal charactor and curvilinear-element section with chines oscillating vertically at high frequency in a free surface. (2) Hydrodynamic pressure on the surface of the shell plate in local vibration in an ideal fluid.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.6
• /
• pp.551-563
• /
• 2007

Numerical analysis for flow characteristics of a twin skeg container ship was carried out according to skeg vertical angles($0^{\circ}$, $10^{\circ}$, $20^{\circ}$) and skeg distances(16m, 20m, 24m) by using a commercial CFD code, FLUENT. Computed: pressure distributions, wake distributions and resistance coefficients have been compared with experimental and WAVIS results carried out by MOERI. Flow characteristics from numerical analysis such as nominal wake fractions, wake distribution and directions of the transverse vectors give good agreement with WAVIS results, even though there are quantitative discrepancy comparing with experimental measurements at the propeller plane. It is found that the better resistance performance can be obtained with the increase of the skeg vertical angle and the decrease of the skeg distance, which are mainly caused by viscous pressure resistance due to the skeg form and pressure recovery around the skeg. In addition, a vertical angle of the skeg gives more effect to the resistance coefficient comparing with the skeg distance. On the basis of results of the present study, it shows that numerical analysis using the commercial code, FLUENT, is useful and efficient tool for the evaluation of the complex stern hull form with twin-skegs.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.2
• /
• pp.97-104
• /
• 2009

Ever increasing fuel prices, almost doubled in the last three years, and global pressure to reduce their environmental impact have been enforcing commercial vessel operators and designers to re-assess current vessel designs with emphasis on their propulsion systems and operational practices. In this paper the "Inclined Keel Hull (IKH)" concept, which facilitates to use larger propeller diameter in combination with lower shaft speed rates and hence better transport efficiency, is explored for a modern 3600 TEU container vessel with the aim of fitting an 13 % larger diameter propeller (and hence resulting 20% lower rpm) to gain further power saving over the similar size basis container ship with conventional "level keel" configuration. It appears that successful application of the "inclined keel Hull" concept is a fine balance amongst the maximum gain in propulsive efficiency, minimum increase in hull resistance and satisfaction of other naval architectural and operational requirements. In order to make the concept economically more viable, this paper concentrates on the fore body design with the possible combination of increase of volume in its fore body to recover the expected volume loss in the aft body due to the space for larger propeller and its low wave-making resistance to minimize the efficiency loss using a well-established optimization software.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.47 no.4
• /
• pp.435-442
• /
• 2011

In an attempt to respond to the increase in international oil prices and reduce operating expenses, ship remodeling was carried out on a 740ton class tuna purse seiner. To strengthen the competitiveness of the fisheries industry by improving vessel performance, a bulbous bow was newly equipped. The slipway and rudder area were also lengthened and enlarged with the propeller and main engine remained unchanged. To reduce the hull resistance, a circle type bulbous bow was attached on the hull behind bow thruster and thus the cost for exchanging electrical equipment for bow thruster was reduced. The new rudder area was expanded 15% more than the old one within the extent that the existing mechanical control part and rudder stock were not changed. To prevent fishing net damage and stabilize wake field, slipway was lengthened to the optimal position. All of the new design of remodeling parts went through the model tests in towing tank and CWC. Besides resistance test, all of necessary model test results were delivered for hydrodynamic character for the modified ship. The maneuvering simulation to verify that the remodeled ship satisfies the IMO rules was performed in both zigzag and turning tests. The estimated resistance with new bulbous bow and lengthened stern was reduced by 4.8% in the 2-dimensional analysis and 17.4% in the 3-dimensional analysis in comparison of conventional ship. The average reduction of resistance was estimated about 10%. Maneuvering character of modified hull form was found to satisfy all regulations under IMO. The remodeling of tuna purse seiner can not only improve fishing performance but also contribute to reduction of operating cost by saving energy for the fisheries industry.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.9 no.1
• /
• pp.1-6
• /
• 1972

To contribute towards more accurate estimation of the virtual coefficient for the vertical vibration of the chine-type ship, experimentally obtained three-dimensional correction factors, J, of added mass of prismatic beams having cross section shape of hypotrocoid characters, slightly concaved Lewis form and elliptic form are investigated in connection with the applicability of an approximate analytical calculation method compared to that proposed by T. Kumai[6] for the Lewis form cylinders, and synthetically in compared with the experimental works on various cross section shapes of the other type by L.C. Burril et al[8] and the analytical works on the ellipsoid of revolution by F.M. Lewis[1] and J.L. Taylor[2]. The experimental results show that the aforementioned analytical method gives, unlike that for the Lewis form cylinders, considerably larger J-values for the chine-type cylinders, and that the influence of the character of the cross section shape on J-values is not remarkable in practical sense. Finally, considering in synthesis the experimental results on prismatic beams, the Burril's works on palabolic plan form and elliptic plan form, and that the chine-type ship usually has a hull form of transom stern, it is fairly safe to say, at the present stage, that adoptation of the Taylor's J-values will not results in any large error in estimation of the virtual inertia coefficients of the chine-type ships.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.1 s.145
• /
• pp.134-146
• /
• 2006

This paper presents the primary conceptual design results of twenty-passenger class Wing-In-Ground(WIG) effect craft. As a first step, top level requirements were proposed and principal dimensions were determined. Maximum speed in ground effect condition is 150 km/h with two tons payload including passengers. Total weight is estimated as 8.5 tons with 2 tons of thrust. Hull and airfoil sections were designed and self propulsion tests were performed by radio controlled model. Two planing hull forms with the transom stern were proposed and towing tests were performed. The resistance and running attitude were measured and the feasibility is checked for the prototype hull form of the twenty-passenger class WIG craft. The free running tests show the stable smooth running attitude at designed speed. Also this radio controlled model can take off around 0.15 meter wave height. It can be said that the top level requirement for the twenty passenger class WIG ship is satisfied successfully. The design optimization to increase the transport efficiency and safety will be performed in the near future.

• Composites Research
• /
• v.34 no.6
• /
• pp.350-356
• /
• 2021

When a ship with a planing line operates or turns in a straight line, the floating position and trim change according to the speed, and a large resistance is generated on the hull. In this paper, the resistance to a planing line was estimated through the computational fluid dynamics of a leisure boat with improved hull weight and durability by applying a carbon composite material to the hull. The resistance performance of the bow and stern of the 18ft class leisure boat was checked and the flow field of the entire vessel was estimated, and the stability of the planing line was confirmed by comparing the resistance of each trim through numerical analysis. In addition, it was confirmed that the designed planing line could withstand it sufficiently because the force applied to the hull was not large, and The stability of the boat was analyzed by calculating the wavelength of the wave and the length of the ship as the ratio of gravity to the inertial force and checking how much force the rolling occurred.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.1 no.1
• /
• pp.50-56
• /
• 2009

The hydrodynamic effect of appendages for high-speed passenger vessels, such as Ro-Pax, Ro-Ro and cruiser vessels, is very severe and, therefore, it is essential to carry out the design of appendages for high-speed passenger vessels from the preliminary design stage to the final detail design stage through a full survey of the reference vessels together with sufficient technical investigation. Otherwise, many problems would be caused by mismatches between the appendages and the hull form. This paper investigates the design characteristics of some appendages, such as the side thruster, the shaft-strut, and the stern wedge, based on the design experience accumulated at Samsung, on CFD, and on model test results for high-speed passenger vessels. Further to this investigation, some practical and valuable design guidelines for such appendages are suggested.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.29 no.1
• /
• pp.103-107
• /
• 2005

This study was carried out to examine the prediction of ship's manoeuvrability in initial design stage. New parameter representing basic hull form and stern shape were proposed. Captive model test were carried out to investigate the correlation coefficient between hydrodynamic coefficient and hull parameter. The results showed which parameter are positive correlation with hydrodynamic coefficient. Moreover correlation was examined between sternhull shape and ship's manoeuvrability. These results can be used to predict a ship's manoeuvrability in initial design stage.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.1
• /
• pp.1-10
• /
• 1997

Viscous flow around actual ship is calculated by an use of RANS equations. The propriety of this computing method, usefulness to hull form design and the scale effect which is the effect of viscous flow depending on the scale of ship model are investigated. Reynolds stress is modelled by using k-${\varepsilon}$ turbulence model and the law of wall is applied near the body. Body fitted coordinates are introduced for the treatment of the arbitrary 3-dimensional shape of the ship hull form. The transformed equations in the computational domain are numerically solved by an employment of FVM. In the calculation of pressure, SIMPLE method is adopted and the solution of the discretized equation is obtained by the line-by-line method with the use of TDMA The calculations of two ships, 4410 TEU container carrier and 50,000 DWT class bulk carrier, are performed at model and actual ship scale. The results are compared and discussed with the model test results which are viscous resistance, nominal wake distribution at propeller plane and limiting streamline on the hull surface. They describe the effect of stem form and the scale effect very well. In particular, the calculated nominal wake distribution and limiting streamline are agreed qualitatively with the experiments and the viscous resistance values are estimated within ${\pm}5%$ difference from the resistance tests.