• Journal of Photoscience
• /
• v.6 no.4
• /
• pp.159-163
• /
• 1999

The fluorescence quenching of 2-phenyl-5-(4-biphenylyl)-1,3,4-oxadiazole (PBD) and 1,4-di-[2-(5-phenyloxazolyl)]-benzene (POPOP) by aniline has been carried out in different solvent mixtures of dioxane and acetonitrile at room temperature. The quenching is found to be appreciable and a positive deviation from linearity was observed in the Stern-Volmer plot in all the solvent mixtures. Various rate constants for the quenching processes have been determined using a modified Stern-Volmer equation. From the positive deviations of linear Stern-Volmer plots and the dependence of rate constants on the polarity of the solvents, it has been concluded that both static and dynamic quenching processes are responsible for the observed positive deviation in the Stern-Volmer plot.

• Textile Coloration and Finishing
• /
• v.27 no.4
• /
• pp.340-344
• /
• 2015

The interaction between curcumin(1,7-bis[4-hydroxy-3-methoxyphenyl]-1,6-heptadiene-3,5-dione) and ethylamines was studied in DMSO:$H_2O$(5:1, v/v) using absorption and fluorescence measurements. The association constant, $K_{ass}$, and the Stern-Volmer constants were calculated by the Benesi-Hildebrand and Stern-Volmer equation, respectively. Curcumin displayed marked UV-Vis absorption changes and highly responsive fluorescence quenching in the presence of ethylamine and the quenching ability was enhanced almost linearly with the concentration of ethylamines. The apparent Stern-Volmer constant measured for the ethylamine-curcumin system was about 1000-fold greater than that of the triethylamine-curcumin system, indicating considerably greater quenching efficiency of ethylamines.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.25 no.3
• /
• pp.13-18
• /
• 1988

Three-dimensional turbulent flows over ship sterns are measured by using the hot-wire anemometer and static holes in the wind tunnel. A conventional stern and a barge-type stern are adopted for the present study. Three components of mean velocities, pressures on the hull and six components of Reynolds stresses are measured. Longitudinal velocity contours are more parallel to the hull surface and weak bilge vortices appear on the barges type stern rather than the conventional stern. Those viscous flow patterns may have close relations to improvements of the resistance and propulsion performance, which have been verified in the towing tests. Measured data files are valuable for the ensuing numerical studies.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.1
• /
• pp.1-6
• /
• 2001

This study focuses on the potential flow analysis for a hull with the transom stern. The method is based on a low order panel method. The Kelvin type free-surface boundary condition which is known to better fit experimental data for a high speed is applied. To treat a dry transom stern effect a special treatment for the free-surface boundary condition is adopted at the free-surface region after the transom stern. Trim and sinkage, which are important in high speed ships, are considered by an iterative method. Pressure and momentum approaches are used to calculate the wave resistance. Numerical calculations are performed for Athena hull and these results are compared with the experimental data and also other computational results.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.109-111
• /
• 2014

본 논문에서는 노드의 속성정보를 통해 노드의 움직임을 예측하는 PPoP(The Path Prediction algorithm based on Probability) 알고리즘을 제안한다. 기존 이동 예측 알고리즘들은 GPS(Global Positioning System)를 사용해 노드의 이동을 학습을 통해 패턴화 하여 예측한다. 이때, 노드들이 이동 패턴을 벗어날 경우 예측률이 떨어진다. 따라서 본 논문에서는 스테른 게를라흐의 실험(Stern-Gerlach experiment)을 분석하여 노드의 이동성을 예측하는 알고리즘을 제안한다. 본 논문에서 제안된 알고리즘에서는 노드의 이동 경로를 staore-carry-forward 방식으로 상황 인지에 의한 경로 설정 변경 예측 방법으로 이동 예측 확률 기법이다. 모의실험 결과 제안한 방법을 사용하여 노드의 이동성 및 패턴을 벗어난 상황에서도 노드의 예측 하고자 한다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.518-530
• /
• 2020

The present study concerns the stern slamming load of container carriers, with stern bulb arrangement variation. First, a series of wedge drop tests were conducted using simple wedge models with fixed deadrise angles, and tests with the cross-section models of practical container carrier sterns were followed. The deadrise angle of the simple wedge ranged from 0° to 10°. The pressure measurement results of the simple wedge drop tests were distributed between empirical formula and analytic solution, so the experimental setup was validated. In the cases of practical hull cross-sections, the water entry of the bulb prior to that of the transom resulted in characteristic water film generation and delayed pressure peak appearance. The trapped air between the bulbs damped the pressure in the twin skeg hull case, reducing the pressure peak and causing the pressure oscillation during water entry.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.5
• /
• pp.653-660
• /
• 2010

The stern tube bearing is installed to the stern tube and stern boss casting by using the method of the force pressured fitting. The adequate value of the interference between the stern tube bearing and casting should be considered owing to the slip. In this study, to review and compare the fitting force and the contact pressure, the theory of thick walled cylinder is considered to clarify the formula which received from the maker. Also the fitting force and contact pressure are calculated by using the standard value of interference, Young's modulus, Poisson's ratio and friction coefficient.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.5
• /
• pp.27-32
• /
• 2011

Recently, a ship-shaped barge has been developed to improve the resistance performance, as well as course-keeping capability. However, the stern of the barge is still similar to a box shape, and the vortex generated at the side of the barge creates drag and yaw instability. In order to solve this problem, stern skegs are normally used. The present paper deals with the correlation between the size of the stern skegs and the barge dimensions and hull coefficient. A stern skeg was designed to prevent yaw instability and minimize any additional resistance. The resistance test and course keeping test were performed in the towing tank at Pusan National University. To determine the correlation parameters between the designed stern skeg size and barge dimensions, a parametric study was also performed. Based on the experimental data from five barges, the optimum skeg dimensions were successfully derived. It is expected that the validation of the present study will be carried out by further experiments and computational comparisons in the near future.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2017.11a
• /
• pp.232-233
• /
• 2017

In this research, tunnel stern was applied on the asymmetric high-speed catamaran to evaluate vessel's hydrodynamic performance by numerical method, and the tunnel stern types are distinguished by angle of inclination of tunnel exit region into 3cases ($0^{\circ}$, $3^{\circ}$ and $6^{\circ}$). Consequently, it is confirmed that the total resistances of tunnel stern which have $0^{\circ}$ of inclination are lower about 4.8-17.9% than the bare hull in the wide speed range, but those of $3^{\circ}$ and $6^{\circ}$ of inclination tunnel stern are higher than bare hull about 5-14% and 5-29%, respectively. On the other hand, trim angles of $0^{\circ}$ of inclination tunnel stern show similar trend with those of bare hull in whole ranges of FnV but those of $3^{\circ}$ and $6^{\circ}$ of inclination tunnel stern are stabilized and declined respectively after FnV=1.54. These phenomena indicated that increasing angle of inclination of tunnel exit region had negative influence on resistance performance, however, it could make vessel's operation performance better than bare hull.

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.08a
• /
• pp.192-193
• /
• 2001

No Abstract.See Full-text