• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.33 no.1
• /
• pp.9-16
• /
• 1984

This paper describes the minimum cost expansion planning which is based on the economical aspect under the various conditions on the power system expansion planning. It presents not only linear cost characteristics analysis but also stepwise cost characteristics analysis which satisfies practical condition in the power system. The latter analysis must be handled by integer programming (IP), because the relation between the cost and the capacity has stepwise characteristics. In order to proceed the latter analysis, the solving procedure is illustrated in detais by using branch and bound method which includes the network flow theory and maximum flow-minimum cut theorem.

• Proceedings of the KIEE Conference
• /
• 2001.11b
• /
• pp.350-353
• /
• 2001

This study proposes a new method for the transmission system expansion planning using the fuzzy integer programming. It presents stepwise cost characteristics analysis which is a practical condition of an actual systems. A branch and bound method which includes the network flow method and the maximum flow-minimum cut set theorem has been used in order to proceed the stepwise cost characteristics analysis. Uncertainties of the permission of the construction cost and not strict reserve rate and load forecasting of expansion planning have been included and also processed using fuzzy set theory in this study. In order to proceed the latter analysis, the solving procedure is illustrated in detail by branch and bound method which includes the network flow method and maximum flow-minimum cut set theorem. Finally, case studies on 21-bus test system show that the algorithm proposed is efficiently applicable to the practical expansion planning of transmission systems in future.

• Journal of the Korea Society for Simulation
• /
• v.17 no.4
• /
• pp.199-208
• /
• 2008

Lately, since Complementary Metal Oxide Semiconductor(CMOS) image sensor system has low power, low cost and been miniaturized, hardware and applied software studies using these strengths are being carrying on actively. However, the products equipped with CMOS image sensor based polling method yet has several problems in degree of completeness of applied software and firmware, compared with hardware’s. CMOS image sensor system has an ineffective synchronous problem due to superfluous message exchange. Also when a sending of data is delayed continually, overhead of re-sending is large. So because of these, it has a problem in structural stability according to Polling Method. In this study, polling cycle was subdivided in high-speed synchronization method of firmware -based through MCU and synchronization method of Stepwise was proposed. Also, re-connection and data sending were advanced more efficiently by using interrupt way. In conclusion, the proposed method showed more than 20 times better performance in synchronization time and error connection. Also, a board was created by using C328R board of CMOS image sensor-based and ATmega128L which has low power, MCU and camera modules of proposed firmware were compared with provided software and analyzed in synchronization time and error connection.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.10
• /
• pp.1305-1313
• /
• 2013

In this study, a method to apply feature-based simplification to boundary representation models is proposed. For feature-based simplification, a volume decomposition tree is created from a boundary representation model. The volume decomposition tree is represented by regularized Boolean operations of additive volumes, subtractive volumes, and fillet/round/chamfer volumes, and it is generated by stepwise volume decomposition, which consists of fillet/round/chamfer decomposition, wrap-around decomposition, volume split decomposition, and cell-based decomposition. After the volume decomposition tree is transformed to an infix expression, the CAD model can be simplified by reordering the volumes. To verify the proposed method, a prototype system was implemented, and experiments on test cases were conducted. From the results of the experiments, it is verified that the proposed method is useful for simplifying CAD models based on boundary representation.

• The Korean Journal of Applied Statistics
• /
• v.29 no.7
• /
• pp.1155-1163
• /
• 2016

This paper deals with an estimation procedure of variance components in a mixed effects model by projections. Projections are used to obtain sums of squares instead of using reductions in sums of squares due to fitting both the assumed model and sub-models in the fitting constants method. A projection matrix can be obtained for the residual model at each step by a stepwise procedure to test the hypotheses. A weighted least squares method is used for the estimation of fixed effects. Satterthwaite's approximation is done for the confidence intervals for variance components.

• Journal of Microbiology and Biotechnology
• /
• v.10 no.4
• /
• pp.476-481
• /
• 2000

A linear correlation, by the stepwise multiple regression analysis, was found between the sensory test of Sigumjang aroma and the gas chromatographic data which were transformed with logarithm. GC data is the most objective method to evaluate Sigumjang aroma. A multiple correlation coefficient and a determination coefficient of more than 0.9 were obtained at the 9th and 13th steps, respectively. At step 31, the coefficient of determination level of 0.95 was attained. The accuracy of its estimation became higher as the number of the variables entered into the regression model increased. Over 90% of the Sigumjang aroma was explained by 13 compounds indentified on GC. The contributing proportion of the peak 26 was the highest followed by peaks 57 (9.27%), 29 (7.51%), 54 (6.01%), 8 (5.99%), 49 (4.97%), and 13 (4.11%).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.6
• /
• pp.2840-2850
• /
• 2011

Programmers can use the Hardware-Software Co-Designing, in which they design a hardware system and software system simultaneously and then unify them, to design an embedded system. This study analyzes the problems of designing an embedded system and suggests applying the system-level design technique, which uses SpecC technology, as a solution to the problems. Also, it suggests systematic and concrete stepwise refinement by applying Refactoring technology in software engineering as a way to make the use of system-level stepwise refinement.

• Journal of the Korean Data and Information Science Society
• /
• v.26 no.2
• /
• pp.347-354
• /
• 2015

This paper deals with a method for intrablock anlaysis of balanced incomplete block designs on the basis of projections under the assumption of mixed effects model. It shows how to construct a model at each step by the stepwise procedure and discusses how to use projection for the analysis of intrablock. Projections are obtained in vector subspaces orthogonal to each other. So the estimates of the treatment effects are not affected by the block effects. The estimability of a parameter or a function of parameters is discussed and eigenvectors are dealt for the construction of estimable functions.

• The Journal of the Korea Contents Association
• /
• v.14 no.2
• /
• pp.319-329
• /
• 2014

Purpose: The purpose of this study was to investigate the effect of adolescent's family function, impulsive behavior, stress on the bullying types. Method: Data were collected from 627 adolescents and analyzed using descriptive statistics, t-test, Pearson correlation coefficients and stepwise multiple regression with the SPSS 18.0. Results: The bullying types (injurer and victim) correlates with family function, impulsive behavior and stress. Stepwise multiple regression analysis showed emotional reactivity, non-planning impulsiveness, friends related stress, experience of drinking (yes), experience of parent depression problem (yes), explained 34.1% of the total variance in bully injurer. Stepwise multiple regression analysis showed communication, motor impulsiveness, friends related stress, gender (male), grade (junior high school), explained 30.9% of the total variance in bully victim. Conclusion: The results of this study are expected to be used as basic data in providing a better understanding of adolescents' bullying, in preventing bullying and in developing an intervention program.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.1
• /
• pp.50-57
• /
• 2010

Stepwise production of syn-gas and hydrogen from methane on ferrite based media added with yttria-stabilized zirconia (YSZ) was carried out using a fixed bed infrared reactor. In this study, all M-ferrite (M=Co, Cu, Mn and Ni) media were prepared by co-precipitation method, and there the YSZ was added as a binder to improve thermal stability, reactivity, and resistance against carbon deposition. Most of the ferrite media containing YSZ showed the good redox property for temperature programmed reduction/oxidation (TPR/O) tests. Notably, the Cu-substituted ferrite medium with YSZ showed the great resistance against carbon deposition as well as the good reactivity for the stepwise production of syngas and hydrogen. Furthermore, it also showed the good durability without significant deactivation during five repeated cyclic tests.