• Journal of Power Electronics
• /
• 제19권2호
• /
• pp.363-379
• /
• 2019

Resonant converters have attracted a lot of attention because of their high efficiency due to the soft-switching performance. An isolated high step-up converter with secondary-side resonant loops is proposed and analyzed in this paper. By placing the resonant loops on the secondary side, the current stress for the resonant capacitors is greatly reduced. The power loss caused by the equivalent series resistance of the resonant capacitor is also decreased. Clamp diodes in parallel with the resonant capacitors ensure a unique discontinuous current mode in the converter. Under this mode, the active switches can realize soft-switching during both turn-on and turn-off transitions. Meanwhile, the reverse-recovery problems of diodes are also alleviated by the leakage inductor. The converter is essentially a step-up converter. Therefore, it is helpful for decreasing the transformer turn-ratio when it is applied as a high step-up converter. The steady-state operation principle is analyzed in detail and design considerations are presented in this paper. Theoretical conclusions are verified by experimental results obtained from a 500W prototype with a 35V-42V input and a 400V output.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1951-1953
• /
• 2004

In this study, we propose a small high voltage power supply which use a half-bridge ZCS resonant and Cockroft-Walton on circuit, for ESP (Electrostatic Precipitator). This power supply transfers energy from ZCS resonant inverter to step-up transformer and the transformer secondary is applied to the Cockroft-Walton circuit for generating high voltage as discharging source of electrodes. It is highly efficient because its amount of switching losses are reduced by virtue of the current resonant half-bridge inverter, and also due to the small size, low parasitic capacitance in the transformer stage owing to the low number of winding turns of the step up transformer secondary combined with the Cockroft-Walton circuit. From these results, the best operational condition is obtained at the switching frequency of 9 kHz and the duty ratio of 50 % in this ESP.

• Journal of Electrical Engineering and Technology
• /
• 제10권6호
• /
• pp.2297-2306
• /
• 2015

This paper presents the development of a system with a reverse matrix converter (RMC) for permanent magnet synchronous motor (PMSM) drive and its effective control method. The voltage transfer ratio of the general matrix converter is restricted to a maximum value of 0.866, which is not suitable for applications whose source voltages are lower than the load voltages. The proposed RMC topology can step up the voltage without any additional components in the conventional circuit. Its control method is different from traditional matrix converter’s one, thus this paper proposes control schemes of RMC by means of controlling both the generator and motor side currents with properly designed control loop. The converter can have sinusoidal input/output current waveforms in steady state condition as well as a boosted voltage. In this paper, a hardware system with an RMC for a PMSM drive system is described. The performance of the system was investigated through experiments

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.27-34
• /
• 1995

The analysis of nonlinear equivalent circuit and the resonance characteristics of input current and output voltage were simulated, and their electrical properties are discussed in the transverse-type piezoelectric ceramic transformer. The nonlinear resonance characteristics of input current and output voltage showed by the thermal effect due to a higher driving current, the nonlinearity increased greatly as driving current increased. When load resistor was 100[M.ohm.], the nonlinear coefficient was -1.3. The nonlinear resonance curve of input current and output voltage for a variation of input voltage and load resistor agreed with the discussed theory. The output voltage increased nearly proportioned to input voltage when load resistors were below 50[M.ohm.], the voltage step-up ratio decreased when a load resistor was 100[M.ohm.] and their maximum value was 950.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.367-370
• /
• 2004

This paper present a new disk-type piezoelectric transformer. The input side of the transformer has a crescent-shaped electrode and the output side has a focused poling direction. The piezoelectric transformers operated in each transformer's resonance vibration mode. The electrodes and poling directions on commercially available piezoelectric ceramic disks were designed so that the planar or shear mode coupling factor $(k_p,\;k_{15})$ becomes effective rather than the transverse meed coupling factor $(k_{31})$. A single layer prototype transformer, 26[m] in diameter and 2.0[mm] thickness, was fabricated, such as step-up ratio, power transformation efficiency and temperature were measured.

• 전력전자학회논문지
• /
• 제17권1호
• /
• pp.67-76
• /
• 2012

This paper proposes the aggregated modeling and control of integated boost-flyback converter (IBFC) for understanding of dynamics characteristic and designing of relevant controller. The basic concept of the aggregated modeling is to substitute the boost or the flyback converter with an equivalent current source. Since each converter with equivalent current source corresponds to the basic boost and flyback converters, the overall mathematical process is significantly simplified for the modeling. Afterwards each result is combined to construct the complete model of the IBFC, and the relevant controller is designed through the achieved small-signal model. Simulation and experimental results show excellent agreement with the theoretical expectations.

• Journal of Power Electronics
• /
• 제11권5호
• /
• pp.669-676
• /
• 2011

A novel polarity inversion dc-dc power conversion circuit that features the high input to output step-up voltage conversion ratio characteristics is presented for high voltage DC power supply applications. The proposed circuit features the reduced voltage stresses of the components compared to those of the conventional ones. The operational principles of the proposed circuit are analyzed and comparative features are presented. The simulation results and experimental results are presented to verify the validity of the proposed circuit.

• 전력전자학회논문지
• /
• 제14권3호
• /
• pp.220-227
• /
• 2009

본 논문은 고전압 DC 파워 서플라이 적용을 위한 높은 전환 비의 자려발진 DC/DC 전력 변환 회로에 관한 것으로써, 하나의 스위치, 하나의 인덕터, 그리고 다수개의 캐패시터와 다이오드로 구성된다. 기존의 극성 반전 형DC/DC 컨버터 회로와 비교하여, 고압 변환 트랜스포머 대신에 인덕터를 사용할 수 있어, 자기 소자의 부피 및 크기는 물론 원가저감이 가능하다. 또한 자려 발진(Self Oscillation) 방식을 사용하여 별도의 제어 IC가 필요 없으므로, 회로구성이 대단히 간단하고, 저가격의 전원 회로를 만들 수 있다. 또한 다이오드들의 전압 스트레스가 감소하여 저가격 고성능의 고압 변환장치 구현이 가능하다. 제안된 회로의 동작원리를 설명하고, 타당성을 Simulation 및 실험을 통하여 검증한다.

• The Korean Journal of Ceramics
• /
• 제5권2호
• /
• pp.171-177
• /
• 1999

In the $(Pb_{1-x}M_x)[(Mn_{1/3}Sb_{2/3})_{0.05}Zr_yTi_{0.95-y}]O_3$ system, where M=Ca and Sr, the piezoelectric properties were evaluated to examine the possibility of application to piezoelectric transformer. A Rosen-type piezoelectric transformer was formed, then the electrical properties of voltage step-up ratio, frequency characteristics etc. were analysed. The morphotropic phase boundary was determined to be y=0.475 in $Pb[(Mn_{1/3}Sb_{2/3})_{0.05}Zr_yTi_{0.95-y}]O_3$ system and the piezoelectric properties of this composition was kp=0.59, Qm=1600 and $\varepsilon_r$=1150. Moreover, when 1-2 mol% of Sr are substituted, enhanced piezoelectric properties of kp=0.61, Qm=1600 and $\varepsilon_r$=1400 were shown. The temperature rising (ΔT) of a piezoelectric transformer with $Pb[Mn_{1/3}Sb_{2/3})_{0.05}Zr_{0.475}Ti_{0.475})]O_3 $ composition was $10^{\circ}C$, and the voltage step-up ratio was 500 when the output voltage was 4000V, whereas the ΔT was below $3^{\circ}C$ and the resonant frequency variation ($\Delta f_r$) as a function of load resistance was below 5% when the output voltage was 2000 V. These characteristics are superior to the properties of materials, which were substituted by Ca or without substitution.

• 수산해양교육연구
• /
• 제27권1호
• /
• pp.63-73
• /
• 2015

The purpose of this study was to examine EMG activities and VMO/VL ratio of the vastus medialis oblique, and vastus lateralis during step up exercise according to ankle and knee positions in soccer players with patellofemoral pain syndrome. Methods: Subject(patellofemoral pain syndrome, PFPS: n=8 and without PFPS, non PFPS; NPFPS: n=8) perfomed step up exercise at each knee and ankle position(knee flexion $30^{\circ}$, $60^{\circ}$, and $90^{\circ}$, ankle internal rotation $30^{\circ}$, neutral, and external rotation $30^{\circ}$) while EMG activity was collected. The EMG signals were expressed by the % maximal voluntary isometric Contraction(%MVIC) values. Statistical analysis consisted of two way repeated measures analysis of variance with post hoc analysis. Results: Main results were as follows: 1) EMG of VMO, and VL was tend to be lower in PFPS compared to NPFPS. 2) EMG of VMO and VL with knee flexrion $60^{\circ}$ was significantly higher the results with knee flexion $30^{\circ}$, and $90^{\circ}$. VMO and VL with ankle external rotation $30^{\circ}$ was significantly higher the results with internal rotation $30^{\circ}$ and neutral position. Conclusion: Considering the EMG activity was reduced due to the to the PFPS and that performing step up with knee flexion $60^{\circ}$ with ankle external rotation $30^{\circ}$ position may provide the most effective condition for patients with patellofemoral pain syndrome.