• 대한관절경학회지
• /
• 제2권1호
• /
• pp.93-96
• /
• 1998

We treated 10 cases of the medial malleolar fracture of the ankle by open reduction and internal fixation from June 1997 to December 1997. After the rigid internal fixation, we measured the gap of the fracture site and the step off of the articular surface by special instrument under the ankle arthroscopy whether it was reduced anatomically or not. And we tried to know the necessity of the arthroscopically assisted reduction and fixation in the medial malleolar fracture of the ankle. Under the arthroscopic view, all 10 cases were anatomically reduced as less than 1 mm of gap of the fracture site and less than 1mm of step off of the articular surface after open reduction and internal fixation in the medial malleolar fractures. In conclusion, through the arthroscopic management, it has advantage in finding and treating the accompanying intraarticular lesion, but also has disadvantage in setting the arthroscope and prolonging the operation time.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.1103-1104
• /
• 2008

In this paper, authors propose a novel step-up AC-DC chopper operated with power factor correction (PFC) and with high efficiency. The proposed chopper behaves with discontinuous current control (DCC) of input current. The input current waveform in the proposed chopper is got to be a discontinuous sinusoid form in proportion to magnitude of ac input voltage under the constant duty cycle switching. Therefore, the input power factor is nearly unity and the control method is simple. In the general DCC chopper, the switching devices are turned-on with the zero current switching, but turn-off of the switching devices is switched at current maximum value. To achieve a soft switching of the switching turn-off, the proposed chopper is used a new partial resonant circuit. The result is that the switching loss is very low and the efficiency of chopper is high.

• 한국진공학회지
• /
• 제12권S1호
• /
• pp.79-82
• /
• 2003

We present the investigation on P- and As-desorption process from the (001) InP surface in metal organic chemical vapor deposition using surface photoabsorption (SPA). The monochromatic SPA signal showed rapid initial increase to reach In-stabilized surface value after $PH_3$ was turned off, but in case of As-desorption, the signal showed clear existence of a metastable state after the $AsH_3$ was turned off. The SPA spectra at each stable surfaces were taken to confirm the interpretation. This result indicates that the As-desorption process should be understood as a two-step process, in contrast to P-desorption of one-step process.

• 한국통신학회논문지
• /
• 제15권8호
• /
• pp.659-666
• /
• 1990

최근에 이산치 2차원 시스템을 기술하는 여러가지 상태공간모델이 제안되어 왔다. 본 논문에서는 Roesser가 제안한 상태공간모델을 근거로 상태궤환을 이용하여 2차원 시스템의 극배치 문제를 고찰한다. 극배치 설계는 2단계로 나누어 1단계에서는 변환된 시스템의 비대각 행렬(off diagonal matrix)을 0으로 하는 조건을 유도하고 2단계에서는 2차원 시스템의 극배치 문제가 2개의 1차원 시스템의 극배치 문제도 된다는 것을 보여준다. 마지막으로 극배치 기법을 설명하기 위한 예를 들었다.

• 전기의세계
• /
• 제17권4호
• /
• pp.18-27
• /
• 1968

Analysis of the transient stability of power systems following disturbances involves many sets of non-linear differential equations. This paper attempts to analyze the transient stability of multi-machine power systems by the step by step method, using the electronic digital computer. The critical switching times and phase angles for the main 154KV transmission system in Korea, are given from the swing curves of the probable conditions. It is concluded that the system is, in general, stable if the relay is cut off within 12 cycles after the fault. However the fault of DAEGU-SANGJU branch, accompanying much real power, makes the system unstable when the raly is cut off within 4 cycles after fault or automatic voltage regulators are equipped in this branch.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.174-175
• /
• 2005

Initial growth stage was investigated for SiC homoepitaxial film growth using 'step controlled epitaxy' technique. When the off angel direction is located parallel along to the gas flow direction, the smoother surface can be obtained. On the on axis substrates, selective etching was detected both the etching and growth condition. It was deduced that the high ratio of C/Si in the source gas results in well developed steps and etched spiral around micropipes.

• Journal of Information Display
• /
• 제6권3호
• /
• pp.18-21
• /
• 2005

A new technology for reducing photolithography process from a four step to a three step process in the fabrication of TFT LCD is introduced. The core technology for 3-mask-TFT processes is the lift-off process [1], by which the PAS and PXL layers can be formed simultaneously. A different method of the lift-off process was developed in order to enhance the performance of efficiency with conventional positive and not negative PR which is the generally used in other lift-off process. In addition, the removal capacity of the ITO/PR in lift-off process was evaluated. The evaluation results showed that the new process can be run in conventional TFT production condition. In order to apply this new process in existing TFT process, several tests were conducted to ensure stability of the TFT process. It was found that the outgases from PR on the substrate in ITO sputtering chamber do not raise any problem, and the deposited ITO film beside the PR has conventional ITO qualities. Furthemore, the particles that were produced due to the ITO chips in PR strip bath could be reduced by the existing filtering system of stripper. With the development of total process and design of the structure for TFT using this technology, 3-mask-panels were achieved in TN and IPS modes, which showed the same display performances as those with the conventional 4mask process. The applicability and usefulness of the 3-mask process has already verified in the mass production line and in fact it currently being used for the production of some products.

• 한국수소및신에너지학회논문집
• /
• 제21권5호
• /
• pp.355-363
• /
• 2010

High purity hydrogen, 97-99 vol.%, with CO at just ppm levels was obtained in a fixed bed of iron oxide employing the steam-iron cycle operation with reduction at 823K and oxidation in a steam-$N_2$ mixture at 773K TGA experiments indicated that temperature of the reduction step as well as its duration are important for preventing carbon build-up in iron and the intrusion of $CO_2$ into the hydrogen product. At a reduction temperature of 823K, oxide reduction by $H_2$ was considerably faster than reduction by CO. If the length of the reduction step exceeds optimal value, low levels of methane gas appeared in the off-gas. Furthermore, with longer durations of the reduction step and CO levels in the reducing gas greater than 10 vol.%, carbidization of the iron and/or carbon deposition in the bed exhibited the increasing pressure drop over the bed, eventually rendering the reactor inoperable. Reduction using a reducing gas containing 10 vol.% CO and a optimal reduction duration gave constant $H_2$ flow rates and off-gas composition over 10 redox reaction cycles.

• Journal of Power Electronics
• /
• 제17권6호
• /
• pp.1445-1453
• /
• 2017

In this study, a new zero-voltage transition (ZVT) buck converter with coupled inductor using a synchronous rectifier and a lossless clamp circuit is proposed. The regular buck converter with tapped inductor has extended duty cycle for high step-down applications. However, the leakage inductance of the coupled inductor produced considerable voltage spikes across the switch. A lossless clamp circuit is used in the proposed converter to overcome this problem. The freewheeling diode was replaced with a synchronous rectifier to reduce conduction losses in the proposed converter. ZVT conditions at turn-on and turn-off instants were provided for the main switch. The synchronous rectifier switch turned on under zero-voltage switching, and the auxiliary switch turn-on and turn-off were under zero-current condition. Experimental results of a 100 W-100 kHz prototype are provided to justify the validity of the theoretical analysis. Moreover, the conducted electromagnetic interference of the proposed converter is measured and compared with its hard-switching counterpart.

• 대한핵의학회지
• /
• 제39권4호
• /
• pp.231-238
• /
• 2005

목적: 비소세포성폐암(NSCLC)의 FDG-PET 판독 시 SUV만 진단기준으로 사용하면 우리나라와 같이 만성 염증성 폐질환이 호발하는 지역에서는 폐문 및 종격동 림프절에 대한 위양성률이 높다. 이에 최근 국내에 도입된 CT-보정 FDG-PET (PET/CT)을 이용하여 SUV 외에 FDG 섭취양상 및 CT영상에서 림프절 석회화 등의 다른 기준을 어떻게 적용하면 림프절의 악성 유무 판정 및 N 병기 결정에 있어 검사의 정확도가 높아질 수 있는지 전향적으로 알아보았다. 대상 및 방법 : 림프절 절제술을 받기 전에 PET/CT를 시행한 91명의 NSCLC 환자를 대상으로 하였다(남/여: 62/29, 평균나이: $60{\pm}9$ yr). 종격동 대혈관보다 FDG 섭취가 증가되어 있는 폐문과 종격동 림프절의 최대 SUV (maxSUV)와 단경을 측정하고, FDG 섭취증가 병변의 경계 및 석회화 유무를 파악하였다. 이 기준들을 이용하여 PET/CT 소견을 세 단계로 나누어 각각의 진단 성적을 병리결과와 비교하였다. 1단계에서는 maxSUV만을 진단기준으로 사용하였다. 2단계 에서는 1단계에서 정한 cut-off 보다 낮은 maxSUV를 가지는 림프절 또는 높은 maxSUV를 가지더라도 CT 영상에서 석회화가 있거나 높은 attenuation을 보이는 림프절을 양성으로 분류하였다. 3단계에서는 2단계에서 양성으로 분류한 림프절 및 2단계에서 악성으로 분류된 림프절 중 FDG 섭취증가의 경계가 명확하지 않은 림프절을 양성으로 하였다. 결과: 수술로 절제된 총 432개의 림프절 중 28개가 악성, 404개가 양성이었다. 71개가 비정상적인 FDG 섭취증가를 보였다. ROC 곡선 분석을 이용해 구한 cut-off는 maxSUV=3.5였다. 악성 림프절 판정에 대한 민감도, 특이도, 정확도는 각각 1단계에서 64.3%, 86.9%. 85.4%. 2단계 64.3%, 95.0%, 93.1%, 그리고 3단계 57.1%, 98.0%, 95.4%였다. N 병기 일치율은 1단계 64.8%, 2단계 80.2%, 3단계 85.7%였다. 결론: NSCLC 환자의 PET/CT 판독 시 림프절의 FDG 섭취증가 정도뿐만 아니라 병변의 석회화 유무 및 FDG 섭취증가의 경계부분 모양을 함께 고려하면 폐문 및 종격동 림프절의 악성 여부 평가 및 N 병기 결정에 있어 더 탁월한 진단성적을 기대할 수 있을 것으로 생각된다.