• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.443-449
• /
• 2017

The imbalance of air supply and the exhaust on subway platforms has led to the installation of platform screen doors in underground subway stations. This imbalance causes the accumulation of pollutants on the platform and loss of comfort due to the lack of ventilation. In this study, a floor exhaust system was optimized using computational fluid dynamics (CFD) and an optimization program. The optimized floor exhaust system was manufactured and tested experimentally to evaluate the particle collection efficiency. CFX 17.0 and HEEDS were used to analyze the flow field and optimize the principal dimensions of the exhaust system. As a result of the three-step optimization, the optimized floor exhaust system had a total height of 1.78 m, pressure drop of 430 Pa, and particle collection capability of 61%. A fine dust particle collection experiment was conducted using a floor exhaust system that was manufactured at full scale based on the optimized design. The experiment indicated about 65% particle collection efficiency. Therefore, the optimized design can be applied to subway platforms to draw in exhaust air and remove particulate matter at the same time.

• Journal of Korea Water Resources Association
• /
• v.41 no.10
• /
• pp.983-993
• /
• 2008

In recent times, sea level increasing caused by abnormal weather and global warming, sea-sand dredging and complex development causes various kind of erosion damages onto the coastal area in the world. The various types of erosion control and protection methods are applied but there are no signs of fruitful effectiveness. The PC concrete protection block for shore protection structure is practically installed in globally but most of structures in the present day became villainous because of bad accessability. In this study, hydrophilic revetments for control and protection of coastline erosion will be developed in order to make up for a faculty of the shore erosion protection block with better accessibility and excellent protection ability. Experimental measurements were researched to insure for the capacity and facility on reflection coefficient, overtopping volume, and overtopping height characteristics of newly developed shore erosion protection block in model tests. As the result, hydraulic model tests show much excellent than the general step block. Field tests were carried out also to verify through vegetative test on an affinity and construction work test of control-protection on coastline erosion with actual utilization. In the latter case, deposition of sand accumulation occurred in fairly short time at the established reaches and then we can be confirmed to utilize for newly developed block as the revetments for control and protection of coastline erosion.

• Korean Journal of Materials Research
• /
• v.21 no.12
• /
• pp.697-702
• /
• 2011

Two-dimensional (2D) nano patterns including a two-dimensional Bravais lattice were fabricated by laser interference lithography using a two step exposure process. After the first exposure, the substrate itself was rotated by a certain angle, $90^{\circ}$ for a square or rectangular lattice, $75^{\circ}$ for an oblique lattice, and $60^{\circ}$ for a hexagonal lattice, and the $90^{\circ}$ and laser incident angle changed for rectangular and the $45^{\circ}$ and laser incident angle changed for a centered rectangular; we then carried out a second exposure process to form 2D bravais lattices. The band structure of five different 2D nano patterns was simulated by a beam propagation program. The presence of the band-gap effect was shown in an oblique and hexagonal structure. The oblique latticed ZnO nano-photonic crystal array had a pseudo-bandgap at a frequency of 0.337-0.375, 0.575-0.596 and 0.858-0.870. The hexagonal latticed ZnO nano-crystallite array had a pseudo-bandgap at a frequency of 0.335-0.384 and 0.585-0.645. The ZnO nano structure with an oblique and hexagonal structure was grown through the patterned opening window area by a hydrothermal method. The morphology of 2D nano patterns and ZnO nano structures were investigated by atomic force microscopy and scanning electron microscopy. The diameter of the opening window was approximately 250 nm. The height and width of ZnO nano-photonic crystals were 380 nm and 250 nm, respectively.

• Journal of the Korean Society of Physical Medicine
• /
• v.4 no.2
• /
• pp.79-86
• /
• 2009

Purpose：The purpose of this study was to investigated the effect of stability on heel-heights of insole in healthy adults. Methods：Subjects of 39 males measured stability index of the Biodex Stability System(BSS) by wearing shoes of 2cm, 5cm insoles including bare feet. The BSS was consisted of a movable balance platform and the platform was interfaced with computer software that enables the device to serve as an assessment of balance performance. Stability index of the BSS included overall stability index(OSI), anteroposterior stability index(APSI), mediolateral stability index(MLSI). In the BSS, subjects were asked to step on to the platform of the BSS and assume a comfortable position while maintaining slight flexion in the knees, looking straight ahead. Subjects were trained for 10min for adaptation to the heel-height of insole and then they maintained double limb stance for 2min. Biodex platform set to convert Lv.8 into Lv.1 gradually. Results：There were statistically significant differences between heel-heights of insole and stability index of OSI, APSI, and MLSI(p<.05). The result of post-hoc test were as follows; 1)OSI had significant differences between bare feet and 2cm, 5cm. 2)APSI had significant differences between bare feet and 2cm, 5cm. 3)MLSI had significant differences between bare feet and 2cm, 5cm(p<.05). Conclusions：We found that the more heels of insole high, the more stability index increases. In particular, balance index of insole above 5cm more increased and we could acknowledge that the insole above 5cm more effected balance of healthy adults.

• Korean Journal of Dental Materials
• /
• v.45 no.4
• /
• pp.301-310
• /
• 2018

The purpose of this study is to evaluate the compatibility of universal adhesives with two dual-cured resin cements. Eighty human molars were divided into eight groups. Tooth was embedded in self-curing acrylic resin and sectioned horizontally to exposure dentine surface. After polishing with 600-grit SiC paper, adhesives were applied. All-Bond Universal (Bisco), G-premio bond (GC), Scotch-bond universal (3M ESPE), Scotch-bond Multipurpose (3M ESPE) were used in this study. Calibra (Dentsply) as a conventional dual-curing resin cement and RelyX Ultimate (3M ESPE) as an amine free resin cement were used. The adhesives and the cements were applied according to the manufacturer's instructions. Final specimens were cylinder (diameter 2mm, height 3mm) shape. After storing in distilled water at $37^{\circ}C$ for 7 days the shear bond strength (SBS) test was performed. There was no significant difference in shear bond strength between the adhesives when RelyX Ultimate was used (p>0.05). However, when Calibra used with Scotch-bond Multipurpose and All-Bond Universal were used, statistically higher SBS was observed, as compared to the groups which Calibra cements with G-premio bond and Scotch-bond universal adhesive (p<0.05) were used. Within the limitations of this study, RelyX Ultimate resin cement was compatible with universal adhesives of various pH. All-Bond Universal adhesive was compatible with a resin cement containing the tertiary amine.

• Electronic Materials Letters
• /
• v.14 no.6
• /
• pp.718-724
• /
• 2018

With the development of photovoltaic industry, the cost of photovoltaic power generation has become the significant issue. And the metallization process has decided the cost of original materials and photovoltaic efficiency of the solar cells. Nowadays, double printing process has been introduced instead of one-step printing process for front contact of polycrystalline silicon solar cells, which can effectively improve the photovoltaic conversion efficiency of silicon solar cells. Here, the relative cheap Cu paste has replaced the expensive Ag paste to form Ag/Cu composite front contact of silicon solar cells. The photovoltaic performance and the cost of photovoltaic power generation have been investigated. With the optimization on structure and height of Cu finger layer for Ag/Cu composite double-printed front contact, the silicon solar cells have exhibited a photovoltaic conversion efficiency of 18.41%, which has reduced 3.42 cent per Watt for the cost of photovoltaic power generation.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.5
• /
• pp.941-948
• /
• 2022

Disaster response robots are deployed to disaster sites where human access is difficult and dangerous. The disaster response robots explore the disaster sites prevent a structural collapse and perform lifesaving to minimize damage. It is difficult to operate robots in the disaster sites due to rough terrains where various obstacles are scattered, communication failures and invisible environments. In this paper, we developed a series connectable wheeled robot module. The series connectable wheeled robot module was developed into two types: an active driven robot module and a passive driven robot module. A wheeled robot was built by connecting the two active type robot modules and one passive type robot module. Two robot modules were connected by one DoF rotating joint, allowing the wheeled robot to avoid obstructions in a vertical direction. The wheeled robot performed driving and obstacle avoidance using only pressure sensors, which allows the wheeled robot operate in the invisible environment. An obstacle avoidance experiment was conducted to evaluate the performance of the wheeled robot consisting of two active driven wheeled robot modules and one passive driven wheeled robot module. The wheeled robot successfully avoided step-shaped obstacles with a maximum height of 80 mm in a time of 24.5 seconds using only a pressure sensors, which confirms that the wheeled robot possible to perform the driving and the obstacle avoidance in invisible environment.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.2
• /
• pp.65-71
• /
• 1984

As a primary step in studying the relationship between the arrangement of netting and the section shape of the bag net in the four-seam trawling net, a series of experiments were performed with the simplified model of the bag net made of vinyl film. This model was suspended horizontally in circularly flowing water, with two pairs of suspending threads to four points of symetry at the border of the bag mouth in place of both wing nets. And then, the area distribution of each panel in the bag net was arranged by the portion of the length of the side panel, q to that of the lower or upper panel, p at the border of bag mouth. In the experiments, the section shape of the bag mouth photographed and the tensions on both pairs of suspending threads were measured with two loadcells in circularly flowing water. From the results that the section shape of the bag mouth in circularly flowing water is controlled by the area distribution of panels in the bag net, the author estimated an experimental equation. h/w=k sub(1) e super(k) 2 super(q/p)+C, where h is the central height of the bag mouth, and w is the lateral width of that.

• The Journal of the Society of Korean Medicine Diagnostics
• /
• v.13 no.1
• /
• pp.19-35
• /
• 2009

Objectives : In the study on the waveform analysis of radial artery pulse diagnosis, we need to establish fundamentals of contemporary pulse diagnosis research. To achieve certain experimental basis on traditional pulse diagnosis, we have to research the differences of pulse waveform according to pressure (in 5 level) and position (Chon, Gwan, Cheok in radial artery). As a first step, in present thesis, we tried to find the differences of pulse waveform according to pressure. Methods and Results : In this research, we analyzed seven parameters of the waveform at five levels of pressure. The parameters are E(so called 'energy', a representative of pulse strength), h1(height of percussion wave) and h2(height of subincisura). The results were as follows. 1. When we analyzed the change of the waveform according to pressure in the left Gwan, E, hl, h2 and A differed between 1st and 2nd grade, between 1st and 3rd grade, between 1st and 4th grade, between 1st and 5th grade, between 2nd and 3rd grade, between 2nd and 5th grade, between 3rd and 5th grade and between 4th and 5th grade in 95% confidence interval. 2. And t2, t4 differed between 1st and 2nd grade, between 1st and 5th grade, between 2nd and 4th grade, between 2nd and 4th grade, between 2nd and 5th grade, between 3rd and 4th grade, between 3rd and 5th grade and between 4th and 5th grade in 95% confidence interval. 3. W differed between 1st and 3rd grade, between 1st and 4th grade, between 2nd and 3rd grade, between 2nd and 4th grade, between 2nd and 5th grade, between 3rd and 4th grade, between 3rd and 5th grade, and between 4th and 5th grade in 95% confidence interval. 4. And h2/h1 differed between 1st and 4th grade, between 1st and 5th grade, between 2nd and 4th grade, between 2nd and 5th grade, between 3rd and 4th grade & between 3rd and 5th grade in 95% confidence interval. 5. There were differences between 1st and 2nd grade & between 2nd and 5th grade in the case of t4/t2 in 95% confidence interval. And there were differences between 1st and 5th grade, between 3rd and 4th grade, between 3rd and 5th grade & between 4th and 5th grade in the case of W/A in 95% confidence interval. And were differences between 1st and 2nd grade, between 2nd and 3rd grade, between 2nd and 4th grade, between 3rd and 4th grade, between 3rd and 5th grade & between 4th and 5th grade in the case of A/E in 95% confidence interval. Conclusions : As mentioned above, we conclude that the waveform analysis according to five grade pressure in the left Gwan shows the difference of waveform in each grade pressure.

• Korean Journal of Heritage: History & Science
• /
• v.50 no.4
• /
• pp.198-221
• /
• 2017

The Jjoksaem site is the eastern sector of Daereungwon Ancient Tomb Complex, Gyeongju(the 512th Historic site) called Wolseong North Burial Ground in academic community. The excavation and research of this site was conducted from 2007 to 2015, with the purpose of basic data offering for the restoration of Silla tumuli and development of ancient tomb park. As a result of the investigation, more than 700 new tombs were discovered except the 155 tumuli founded in the Japanese colonial era. Moreover, more than 70 percent of the smaller tombs, such as outer coffin tombs, were discovered here. There are four characteristics of outer coffin tombs in Jjoksaem site. First, it is recognized the Gyeongju-styled outer coffin tombs have a long rectangular shape, distinct from Gimhae-styled outer coffin tombs in a rectangular shape. Second, they are divided into three groups by the size of the grave area. This is indirectly related to the rank and the status of the buried person. Third, these tombs began to be constructed at the end of the 3rd century before the time of wooden chamber tombs covered by stone and earthen mound. They were ruined because of the new tombs constructed at the period of Maripgan. This reflects that the identity of the former tombs was not respected by the communities in the later generations. Outer coffin tombs were consistently made to the end of the era of wooden chamber tombs covered by stone and earthen mound. Lastly, the area of burial ground of outer coffin tombs is limited by wooden chamber tombs covered by stone and wooden mounds. Otherwise, the location of the burial ground for the deceased is limited by the status of the deceased. The idea that wooden chamber tombs covered by stone and earthen mound are located on the above ground turns out to be incorrect. In Jjoksaem site, there is little difference between the height of the circular burial protection stone and the height of the digging lines of the other tombs. In the case of No.44 tumulus, the lowest step of the circular burial protection stones is lower than those of the other tombs and tumuli. Research of outer coffin tombs at Jjoksaem site will be to suggest important academic data about the changing period from Saroguk, as the head of chiefdom union, to Silla, as state.