• 한국생산제조학회지
• /
• 제8권1호
• /
• pp.81-88
• /
• 1999

This paper was carried out to know the influence of advanced austempered ductile cast iron (ADI) on the tool life and mechanical properties of drilling machinability. For manufactured method of ADI, the spheroidal graphite cast iron were austenized at 90$0^{\circ}C$ for 1 hour and then austempered for 2 hour at 37$0^{\circ}C$ in the salt bath. And interrelationship has been investigated between tool life and mechanical characteristics of specimen material on drilling condition when the ordinary and step-feed drilling are carried out to drill holes of specimens. Tensile strength and hardness of ADI decrease and elongation of ADI increases with the increase austempered temperature. It is known that about 2 times of tool life in the case of step-feed decreases compared with ordinary feed due to the high hardness of ADI and hardness ascribed to the fact that retained austenite became to martensite state due to cutting heat in drilling. Under the constant feed rate 0.1mm/rev relation between hardness and length of end tip after drilling can be formularized to Hv=$788.46L^{-0.096}$ for the cutting speed 6.1m/min.

• 해양환경안전학회지
• /
• 제22권5호
• /
• pp.410-416
• /
• 2016

우리나라는 세월호 사고 이후 해양안전에 대한 중요성이 증대되고 있다. 특히, 해양관련 종사자들에 국한하지 않고 대국민 해양안전의식 고취를 위해 학교 및 해양관련 단체에서 다양한 교육훈련 및 체험교육이 시행되고 있다. 선원의 안전교육은 SOLAS 규정에 의거 여객선은 10일, 상선은 매월 1회 소화 및 퇴선훈련을 실시하고 있다. 세월호 사고 이후 교육훈련의 효과를 증대시키기 위해 교육 정원을 기존 40명에서 20명으로 줄여 모든 교육생이 실제 교육훈련에 참여할 수 있도록 하고 있다. 현재의 교육훈련 형태는 교재에 의거한 이론교육 실시 후 실제 실습을 행하는 2단계 교육훈련이 실시되고 있다. 하지만 현재 인적, 물적 여건상 교육생들에게 많은 실습시간 부여 및 소수인원으로 구성된 실습교육이 곤란한 상황이나 시뮬레이션 기법이 도입될 경우 실습 전 숙달된 능력으로 실습교육의 빠른 진행으로 많은 실제 실습교육 수행이 가능할 것이다. 이러한 이유로 이 연구에서는 해상안전교육 중 소화훈련의 효율성을 증대시키기 위해 총 3단계로 구분한 교육훈련을 제안하고자 한다. 즉, 이론 교육 후 시뮬레이션 기법을 통한 개인별 임무 숙지 및 장비 사용법에 대한 이미지트레이닝교육을 추가하고자 한다. 이러한 시뮬레이션 기법을 사용할 경우 이론교육으로 얻어진 지식을 바탕으로 실제 훈련 전 가상으로 먼저 시행함으로서 실습교육에 빠른 적응이 가능하며 시뮬레이션 특성상 실제 훈련에서는 곤란한 긴급상황 대처훈련 및 다양한 시나리오에 의한 반복훈련이 가능하다. 이렇게 실습 전 숙달된 능력을 바탕으로 실습교육의 진행 속도를 증가시켜 많은 실제 실습교육을 수행할 수 있어 교육훈련 효율성이 증대될 것이다. 실제 교육생 설문조사에 의하면 개인별 실습시간 부족을 지적하였다. 이러한 이유로 가상현실 기법을 이용한 시뮬레이터 개발이 필요하여 이 연구에서는 개발방법에 대해 고찰하였다.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• 제5권1호
• /
• pp.22-28
• /
• 2002

A New concept for the LNG-FPSO ship, with moonpool and bilge step in bottom, is proposed. This concept is investigated with regard to motion reduction and sloshing phenomena of the cargo and operation tanks. The principal dimensions of the ship are $L\timesb B\times D\times t(design)=270.0\times51.0\times32.32\times13.7(m)$, with a total cargo capacity of 161KT; a 98% loading condition is considered for this study. The moonpools and rectangular step at the bilge have been designed for the purpose of decreasing the motion within the tank. For the motion analysis, linearized three-dimensional diffraction theory, with the simplified boundary condition was used. The six-degree of freedom coupled motion responses were calculated for the LNG-FPSO ship. Viscous effects on the roll motion responses of a vessel were taken into account in this calculation program, using an empirical formula suggested by Himeno(1981). The case study for the moonpool size has been conducted using theoretical estimation and the experimental method. For the optimization of the moonpool size and effect of the bilge step, 9 cases of its size, both with and without bilge step, were involved in the study. no motion responses, especially roll motion, for the designed LNG-FPSO ships are much lower than those of other drill ships and shuttle tankers. The limit criterions are satisfied. To check the cargo tank and operation tank sizes, we performed a sloshing analysis in the irregular waves which focuses on the pressure distribution on the tank wall and the time history of pressure and free surface for No.2 and 5 tanks of LNG-FPSO with chamfers. Finally, optimum tank sire was estimated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.773-776
• /
• 2005

An Experiment was carried out to study deburring in frilling hole on the Inclined exit surface. Two different deburring tools, exit surface angles, materials and cutting conditions were selected to check their performance using CNC machining center. In deburring operation, there are not only flat exit surfaces but also inclined exit surfaces which is described as inclination angle. Inclination of exit surface causes a quite different burr formation when comparing with flat surface. Deburring characteristics are analyzed according to the deburring tools and cutting conditions. Several strategies for a effective deburring on inclined exit surface were proposed.

• Restorative Dentistry and Endodontics
• /
• 제24권2호
• /
• pp.337-345
• /
• 1999

The purpose of this study was to compare the shape of root canal after instrumentation with some engine driven NiTi files. Thirty narrow and curved canals(15-35 degree) of mesial canals of extracted human mandibular first molars were divided into three groups. Group 1: After radicular access with Gates Glidden drill, apical shaping using step back method with Flexo file Group 2: After radicular access with Gates Glidden drill, apical shaping with Profile .04 Group 3: Canal shaping with GT file and Profile .04. Using modified Bramante technique, the root was sectioned at 2 mm from apical foramen, height of curvature, 2 mm from canal orifice. Canal centering ratio, amount of transport, amount of dentin removed, shape of canal were measured and statistical analysis is done using SPSS Program V 7.5. The results were as follows: 1. Canal centering ratio of group 3 was the lowest at coronal part, but there was no statistical difference. Centering ratio of group 2 was the lowest at curve part, and there was statistical difference between group 1(P<0.05). Centering ratio of group 2 was the lowest at apical part, but there was no statistic difference. 2. Amount of transport of group 3 was the lowest at coronal part, but there was no statistical difference. Amount of transport of group 2 was the lowest at curve part, and there was statistical difference between group 1(P<0.05). Amount of transport of group 3 was the lowest at apical part, and there was statistical difference between group 1 and group 2, group 1 and group 3(P<0.05). 3. Amount of dentin removed of group 3 was the lowest at coronal part, bur there was no statistical difference. Amount of dentin removed of group 2 was the lowest at curve part, but there was no statistical difference. Amount of dentin removed or group 2 was the lowest at apical part, and there was statistical difference between group 1 and group 2, group 1 and group 3(P<0.05). 4. The shape of the canals after instrumentation varied among the groups. The majority of canals at coronal and curve part for group 1 were round in shape(7 in 10), those at apical part were oval(8 in 10). The majority of canals at coronal part for group 2 were round in shape(7 in 10) and there was no difference in the number of shape at other part. There was no difference in the number of shape at every part for group 3. As above results, NiTi rotary instrumentation showed a trend to remain more centered in the canal than SS file instrumentation. At using NiTi file, coronal shaping with Gates Glidden drill was not statistically different from shaping with GT file. But shaping with GT file showed tapered canals, so it may be said that shaping with GT file is a safe and valuable instrumentation method.

• Restorative Dentistry and Endodontics
• /
• 제16권2호
• /
• pp.174-181
• /
• 1991

A model system was used which enabled the same root canal system to be measured before and after coronal flaring of 51 extracted mandibular molars. The concavity of the distal surface of the mesial root was measured and the amount of reduction was compared after coronal flaring using step-back flared preparation, Gates-Glidden dirll or ultrasonic system(Quick-$\varepsilon$) at the furcation and apical 3mm from the furcation. The results were as follows: 1. The mean concavity of mesial root of manchbular molar was $0.73{\pm}0.27mm$ at the bifurcation and $0.65{\pm}0.23mm$ at the 3.0mm apical from the bifurcation. 2. The thickness of the root canal wall of the mesiobuccal canal was $1.08{\pm}0.26mm$ at the bifurcation and $1.00{\pm}0.23mm$ at the 3.0mm apical from the bifurcation. 3. The thickness of the root canal wall of the mesiolingual was $1.09{\pm}0.21mm$ at the bifurcation and $0.98{\pm}0.29mm$ at the 3.0mm apical from the bifurcation. 4. In the amount of reduction at the furcation and at the 3.0mm apical from the furcation there was no statistically significant difference between the step-back preparation and Gates-Glidden drill preparation, and ultrasonic preparation(P>0.05).

• 한국초등과학교육학회지:초등과학교육
• /
• 제28권2호
• /
• pp.178-186
• /
• 2009

The science writing is recognized for useful learning method to boost up scientific thinking for all class course as well as traditional lecture and experiment. Many researches say that science writing is helpful to extend students' science knowledge and scientific attitude. By the way, the researchers thought that science writing can also improve the science process skill if students participate in delicately organized learning program. In this study, we had contrived the teaching & learning strategy of science writing to improve science process skills. The learning program covers all field of Klopfer's process skills with various forms of writing; explaining writing, logical writing, critical writing, and creative writing. The learning program has been developed for 5th grade students in the regular classes in order to enhance science process skills as well as knowledge and scientific attitude. Not to miss any process skill or various kinds of writing, we used 3 dimensional frame. The axes of the frames are science process skills, forms of writing, and science curriculum contents. The students are given the final writing theme at the beginning of each chapter. They drill science process skills step by step during the classes, and have a chance to talk each other before the final writing. They practice writing skills from one sentence to full article by degrees. The effect of the program was examined by students' work and TSPS (Test of Science Process Skill). The result showed that 5th grade students had a meaningful progress in science process skills as well as knowledge and scientific attitude. we could confirm it with examining students' work in the class.

• 한국기계가공학회지
• /
• 제15권6호
• /
• pp.77-82
• /
• 2016

When drilling through Inconel 601 nickel-chromium-based alloys, a large amount of cutting oil is required to prevent tools from wear and fracturing due to heat buildup resulting from the high temperature resistance and toughness of this alloy. However, cutting oil supply has become a factor compromising the machining environment, and this has caused attention to shift to a more environmentally friendly cutting fluid supply system called minimum quantity lubrication (MQL). Our aim in this study was to find a more efficient drill processing method using MQL, and to verify its performance. To that end, we proposed a sealed cover, a step feed, and POSS-type cutting oil as measures to increase the effectiveness of MQL in view of the cutting force and tool wear, and established an improvement in efficiency using the proposed measures.

• 한국생산제조학회지
• /
• 제26권3호
• /
• pp.285-291
• /
• 2017

Micro-needles are used as transferring devices for sampling of tiny constitute substances from biological bodies. Typically, nickel is used as a coating to improve the rigidity of micro-needles. This study introduces the methodology to manufacture a WC needle with very high hardness and toughness. Micro-EDM technology was used to manufacture micro-needles with holes $130{\mu}m$ in diameter and $2300{\mu}m$ in length. A micro-needle was aligned to the micro-EDM electrode using a custom two degree-of-freedom alignment system. A three-step manufacturing technique was developed to drill a micro-hole using a WC electrode. In the first process, an electrode $105{\mu}m$ in diameter was used to make a hole. Electrodes of 90 and $105{\mu}m$ diameters were used in the second and third process, respectively. Consequently, a WC micro-needle with an inner hole of $135{\mu}m$ diameter, length of $2300{\mu}m$, and outer diameter of $300{\mu}m$ was developed.

• Journal of Periodontal and Implant Science
• /
• 제38권sup2호
• /
• pp.385-394
• /
• 2008

Purpose: The aim of this study was to evaluate the factors affecting healing patterns of surgically created circumferential gap defects around implants in dogs. Materials and Methods: In four mongrel dogs, all mandibular premolars were extracted. After 8 weeks of healing periods, implants were submerged. According to the surface treatment, turned surface was designated as a group A and rough surface as a group B. In each dog, surgical defects on the left side were made with a customized tapered step drill and on the right with a customized paralleled drill. Groups were also divided according to the width of the coronal gaps: 1.0mm, 1.5mm, or 2.0mm. The dogs were sacrificed following 8 weeks and the specimens were analyzed histologically and histomorphometrically. Results: During the postoperative period, healing was uneventful and implants were well-maintained. As the size of the coronal gap was increased, the amount of bone-to-implant contact was decreased. The bone healing was greater in rough surface implants compared to the turned ones. About the defect morphology, tapered shape showed much bone healing and direct bone to implant contact even in the smooth surface implants. Conclusion: Healing of the circumferential defect around dental implant is influenced by the implant surface, defect width and the morphology of the defect. When using rough surface implants, circumferential gap defects within 2 mm do not need any kinds of regenerative procedures and the healing appeared to be faster in the tapered defect morphology than the paralleled one.