• Journal of Power System Engineering
• /
• v.13 no.1
• /
• pp.26-32
• /
• 2009

This study is about roll characteristics evaluation to show the advantage of using MR(magneto-rheological) dampers for steering of a SUV(sports utility vehicle). Roll characteristics is very important to observe the roll-propensity of the SUV. ADAMS/Car program was used to simulate the basic steering motion, using 63 D.O.F. vehicle model. Sky-Hook and Ground-Hook control algorithms were used as a semi-active suspension system controller. The roll characteristics from the steering motion were compared between the simulation results from the semi-active suspension system and the passive suspension system.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.10
• /
• pp.178-186
• /
• 2002

In this study, the steering control system for UCT (unmanned container transporter) was developed using MR (Magnetoresistive) sensors. The MR and magnet sensors are used for the lane detecting system. The robust control theory is used for the design of the steering controller to reduce the uncertainties of the road. The performance of the robust steering controller is compared in simulations and tests using the existing PD controller of the UCT.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.4
• /
• pp.12-24
• /
• 1997

An intelligent steering control system is designed for the steering control of a 4 wheel drive (4WD) electric vehicles without steering mechanism, where the vehicle is assumed to have 3 degree of freedom and input-output feedback linearization is employed. Especially, a fuzzy-rule-based side force estimator is suggested to avoid uncertain highlynonlinearexpression sof relations between side forces and their factors. Also, aneural-network-based predictive compensator is additionally utilized for the vehicle model to be correctly controlled with unstructured uncertainties. The proposed overall control system is numerically shown to be robust against drastic change of the external environments.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.6 s.237
• /
• pp.809-814
• /
• 2005

The goal of this paper is to minimize the weight of the T-structure supporting steering system in reducing the vibration level on steering wheel which could be amplified by the resonance. Presently, requirements for reducing noise, vibration and harshness (NVH) in automotive area are more stringent than ever. One of them is the vibration of steering system which occurs sometimes at high speeds or when the engine is idling. Besides, the reduction of weight is also one of requirements for improvement of vehicle performance. This paper used the micro genetic algorithm as an optimization method to satisfy above two requirements. The whole T-structure assembly including steering column was used for frequency analysis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.5
• /
• pp.834-840
• /
• 2001

A real time multibody vehicle dynamics model has been developed and implemented using a subsystem synthesis method based on recursive formulation. To verify real time simulation capability the developed model has been applied to HMMWV(High Mobility Multipurpose Wheeled Vehicle) with steering system. For the kinematically driven steering system, the coupled front suspension-steering subsystem can be decoupled into two SLA suspension subsystems, which improves the efficiency of simulation. To investigate theoretical efficiency, operational counting method has been also employed to compare the proposed model with the conventional recursive dynamics model. Various simulations such as unsymmetric bump run, step steering(J-turn) and sine steering input test have been carried out to verify the real time feasibility of the proposed model.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.11
• /
• pp.1511-1518
• /
• 2014

Demand for high fuel efficiency and smart features of the vehicles, research has been intensified. Hence, research and development on electric power steering (EPS) system to replace the existing hydraulic steering system has been actively conducted. Permanent magnet motors are widely used in automotive applications due to their high power density and high efficiency. However, increasing price and limited production of rare-earth permanent magnets has recently prompted the auto parts makers to substitute permanent magnet motors by non- or less rare earth magnet motors. Switched reluctance motors SRMs), known as typical non-rare earth motors have simple structure, low manufacturing cost, and high reliability. This paper discusses design, modeling, simulation, and experimental verification of a prototype SRM drive for electric power steering system.

• Journal of Power System Engineering
• /
• v.7 no.3
• /
• pp.61-68
• /
• 2003

Steering characteristics is an important factor in the evaluation of vehicle quality. To estimate steering characteristics in the vehicle conceptual design stage, vehicle dynamics simulation methods are very efficient. However, it is often difficult to simulate vehicle dynamics for the specific driving scenarios in open-loop driving environment. An efficient driver-in-the-loop vehicle model will be efficient for this job. A good tire model is also very important for the accurate vehicle dynamics simulation. In this research, a driver model is used to simulate vehicle steering dynamics for a 8-dof vehicle model with STI(Systems Technology, Inc.) tire model. For the demonstration of this model, a SUV(sports utility vehicle) and a sedan were simulated.

• Transactions of Materials Processing
• /
• v.18 no.5
• /
• pp.385-391
• /
• 2009

An adhesively bonded power steering cylinder with a steel tube and an aluminum bracket was developed to reduce the weight of steering systems. To achieve the joint strength between the steel tube and of the aluminum bracket, the shape aluminum bracket re-designed by using the FE-analysis. Fracture behavior of the adhesive layer was considered by a cohesive zone model(CZM), which is based on the two-parameter fracture phenomenon with critical stress and fracture toughness. From the result of FE-analysis with CZM, re-designed power steering cylinder satisfied the desired joint strength for axial and torsion modes. And its joint strength was verified by the fracture test in each mode.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.1
• /
• pp.1-7
• /
• 2003

When a ship is course-keeping in the open seas, autopilot system is adapted. The design of autopilot system is very important for improvement of ship′s element research. Automatic steering system consists of autopilot device, power unit, steering gear, magnetic or gyro compass and ship dynamics. In order to evaluate automatic steering system of ships in open seas. we need to know the characteristics of each component of the system, and also to know the characteristics of disturbance to ship dynamics. In this paper, I provide evaluation method of autopilot navigation system of the fishing ship. Prediction method based on the principle of linear superposition is introduced for irregular disturbance. For the evaluation of automatic steering system of a ship, "performance index" is introduced from the viewpoint of energy saving and calculation method is frequency response analysis. Finally, I carried out calculation of sensitivity of control constants of autopilot with various conditions of ocean environments.

• Journal of Korean Society for Quality Management
• /
• v.33 no.1
• /
• pp.32-41
• /
• 2005

This paper presents a six sigma application case study for an automobile steering wheel manufacturing process using rolled throughput yield improvement activity. Hidden factory and first pass yield concept is introduced and a DMAIC procedure is implemented to maximize the first pass yield. The result of the six sigma project amounts to the reduction of failure cost of 1.2 billion won per year in the steering wheel manufacturing process. This paper can benefit six sigma practitioners in some ways.