• 한국강구조학회 논문집
• /
• 제21권5호
• /
• pp.493-503
• /
• 2009

교량의 여유도는 주부재의 손상시 하중을 지탱할 수 있는 능력으로서 거더 개수, 지간, 형고, 내부지점, 부부재 등의 다양한 인자가 영향을 미치게 된다. 그러나, AASHTO 및 국내 도로교설계기준과 같은 현행 규정에서는 교량의 여유도를 단지 주거더의 개수로만 정의하고 있고, 그 평가 방법 및 요구 수준은 아직 제시되지 않고 있다. 이에 본 연구에서는 플레이트거더교를 대상으로 심각한 피로손상이 발생한 경우 주요 인자들을 고려하고 신뢰도 기법에 기반하여 교량의 여유도 평가 기법을 제안하였다. 또한, LRFD법 기반의 기준 교량에 대해 손상 시 내하력 해석과 신뢰성 해석을 수행하여 여유도의 요구 수준을 목표 시스템 신뢰도 지수 형태로 제안하였다. 마지막으로 현행 ASD법으로 설계된 단순 및 연속 플레이트거더교의 거더 수에 따른 여유도 수준을 평가 제시하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1300-1309
• /
• 2010

In the railway bridges, steel plate girder types are preferred due the high stability. Nevertheless, it has been pointed out that this type of bridge has problems such as, structural damages in the rail and girder seat, noise problem due to impact at the rail joint and excessive vibration. This vibration and/or deflection are mainly because insufficient stiffness of steel plate type of bridge. To resolve these problems, PC-Slab composite plate girder type which has simple process and economic cost, is proposed in this study. The static and dynamic experiment is performed by using the production of actual sized PC-Slab and abandoned steel plate girder. The object of this experiment is to verify the fact that girder stiffness increase and structural safety. The result of the experiment is used to analyze the effect of performance improvement of PC composite plate girder type. Using this method, economic rail maintainers, girder stiffness increase, and also speed/ride improvement even for existing rail could be expected by dynamic performance improvement. Additionally noise due to impact, deflection and vibration caused from long rails can be reduced.

• 한국강구조학회 논문집
• /
• 제14권5호통권60호
• /
• pp.593-602
• /
• 2002

콘크리트와 강판, PS강재의 구조적 장점을 극대화하여 낮은 형고로 경간을 장대화할 수 있는 새로운 교량 상부구조형식으로서 강재로 구속된 프리스트레스트 콘크리트 합성거더(Steel-Confined Prestressed Concrete Girder; SCP Girder)를 개발하였다. 개발된 SCP 합성거더의 효과적인 설계 및 제작을 위하여 설계프로그램을 개발하고 제작절차를 확립하였다. 이를 바탕으로 설계된 SCP 합성거더를 실물크기로 제작하여 시공성을 확인하였으며, 재하실험을 통해 설계의 타당성과 구조적 안전성 및 실적용 가능성에 대하여 검증하였다.

• Wind and Structures
• /
• 제23권5호
• /
• pp.405-420
• /
• 2016

Section model wind tunnel test is currently the main technique to investigate the flutter performance of long-span bridges. Further study about applying the wind tunnel test results to the aerodynamic optimization is still needed. Systematical parameters and test principle of the bridge section model are determined by using three long-span steel truss suspension bridges. The flutter critical wind at different attack angles is obtained through section model flutter test. Under the most unfavorable working condition, tests to investigate the effects that upper central stabilized plate, lower central stabilized plate and horizontal stabilized plate have on the flutter performance of the main beam were conducted. According to the test results, the optimal aerodynamic measure was chosen to meet the requirements of the bridge wind resistance in consideration of safety, economy and aesthetics. At last the credibility of the results is confirmed by full bridge aerodynamic elastic model test. That the flutter reduced wind speed of long-span steel truss suspension bridges stays approximately between 4 to 5 is concluded as a reference for the investigation of the flutter performance of future similar steel truss girder suspension bridges.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2008년도 정기 학술대회
• /
• pp.197-202
• /
• 2008

In this paper, a hybrid vibration-impedance approaches is newly proposed to detect the occurrence of damage, the location of damage, and extent of damage in steel plate-girder bridges. The hybrid scheme mainly consists of three sequential phases: 1) to alarm the occurrence of damage, 2) to classify the alarmed damage, and 3) to estimate the classified damage in detail. Damage types of interest include flexural stiffness-loss in girder and bolts-loose in supports. In the first phase, the global occurrence of damage is alarmed by monitoring changes in acceleration features. In the second phase, the alarmed damage is classified into subsystems by recognizing patterns of impedance features. In the final phase, the location and the extent of damage are estimated by using modal strain energy-based damage index method and root mean square deviation method. The feasibility of the proposed system is evaluated on a laboratory-scaled steel plate-girder bridge model for which hybrid vibration-impedance signatures were measured for several damage scenarios.

• Steel and Composite Structures
• /
• 제49권2호
• /
• pp.215-230
• /
• 2023

Cable-girder anchorage joint is the critical part of cable-supported bridges. Tensile-plate anchorage (TPA) is one of the most commonly used types of cable-girder anchorage joints in steel girder cable-supported bridges. In recent years, it has been proposed by bridge designers to apply TPA to concrete girder cable-supported bridges to form composite cable-girder anchorage joint (CCGAJ). In this paper, the mechanical performance of CCGAJ under tensile force is studied through experimental and numerical analyses. Firstly, the effects of the external prestressing (EP) and the bearing plate (BP) on the mechanical performance of CCGAJ were investigated through three tests. Then, finite element model was established for parametrical study, and was verified by the experimental results. Then, the effects of shear connector forms, EP, BP, vertical rebar rate, and perforated rebar rate on the tensile capacity of CCGAJ were investigated through numerical analyses. The results show that the tensile capacity of CCGAJ depends on the first row of PR. The failure mode of CCGAJ using headed stud connectors is to form a shear failure surface at the end of the studs while the failure mode using PBLs is similar to the bending of a deep girder. Finally, based on the strut-and-tie model (STM), a calculation method for CCGAJ tensile capacity was proposed, which has a high accuracy and can be used to calculate the tensile capacity of CCGAJ.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.365-375
• /
• 2006

The HR Plates made hot rolled coils is lower than general structural steel plates in price. No difference between general steel plates and HR Plates with thickness up to 22mm are found in most characters such as cutting operation, fabrication and even welding. It can be concluded that HR Plates with thickness up to 22mm can be applied to flanges and webs of any girders as well as longitudinal ribs, longitudinal and vertical stiffeners of steel bridges appropriately. To increase the demand of HR Plates with thickness up to 22mm, it is necessary that HR Plates is applicable to full member in steel bridge including main girder.In this study, availabilities of the narrow steel box girder of light railway transit with HR Plate width as a main member are discussed. For application of HR Plate to steel bridge with 50m span or more, new support systems in three types are presented. Computational analysis is performed in 15 bridge models of light railway transit with beam element and plate element. As a analysis results, three models in light railway transit are presented. We finally come to the conclusion that HR Plates can be apply to narrow steel box girder in the light railway transit.

• Structural Engineering and Mechanics
• /
• 제40권5호
• /
• pp.719-743
• /
• 2011

A hybrid damage monitoring scheme using parallel acceleration-impedance approaches is proposed to detect girder damage and support damage in steel plate-girder bridges which are under ambient train-induced excitations. The hybrid scheme consists of three phases: global and local damage monitoring in parallel manner, damage occurrence alarming and local damage identification, and detailed damage estimation. In the first phase, damage occurrence in a structure is globally monitored by changes in vibration features and, at the same moment, damage occurrence in local critical members is monitored by changes in impedance features. In the second phase, the occurrence of damage is alarmed and the type of damage is locally identified by recognizing patterns of vibration and impedance features. In the final phase, the location and severity of the locally identified damage are estimated by using modal strain energy-based damage index methods. The feasibility of the proposed scheme is evaluated on a steel plate-girder bridge model which was experimentally tested under model train-induced excitations. Acceleration responses and electro-mechanical impedance signatures were measured for several damage scenarios of girder damage and support damage.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.558-564
• /
• 2006

When vehicles pass the connection between the bridge and earthwork, the difference of both sections' stiffness produces an increasing wheelload. As a consequence, it results in the excessive vibration of vehicles and the damage of bearing system. In general, steel plate girder railway bridges without ballast track have larger stiffness than the bridge with ballast, and produces larger impulse on the bridge superstructure. Thus, it is necessary to reduce the differences of both stiffness. This study presents parametric studies on the behavior of plate girder bridges and their tracks by means of various stiffnesses and the length of approach zone. The results of numerical study showed that the smaller the stiffness of both sides and the longer the length of approach zone, the variation of wheelload becomes smaller. Hence, it gives less burden into the plate girder bridges and their tracks. It is expected that the results of parametric study can be used as a preliminary data for the determination of economical length on the approach zone and the stiffness of both sides.

• 한국강구조학회 논문집
• /
• 제20권1호
• /
• pp.183-193
• /
• 2008

국내 LRFD 도로교설계규정을 정립하기 위한 자료로 활용하기 위하여 단경간 및 3경간 연속 플레이트 거더 및 박스 거더 합성단면을 하중저항계수설계법으로 설계하고 설계된 단면의 휨에 대한 신뢰도해석을 수행하였다. LRFD 법에 의한 합성거더 단면 설계 시에는 최근 국내 통행차량의 특성을 분석하여 새로 제안된 활하중을 적용하였다. 신뢰도해석에서 휨저항강도는 최근 국내에서 생산된 16,000여 구조용 강재 표본의 항복강도 통계적 특성을 반영하여 재료 비선형 소성해석으로 구한 강합성단면의 휨저항강도 통계를 이용하였다. 활하중에 의한 작용모멘트의 편심계수는 1.0~1.2를 적용하였으며 강거더 자중, 콘크리트 바닥판 자중, 포장면 자중 등에 의한 고정하중 모멘트 통계 값은 A SHTO 보정자료를 사용하였다. Rackwitz-Fiessler 법으로 신뢰도해석을 수행하고 지간별, 강거더 형식별, 활하중계수별, 활하중 모멘트의 편심계수별로 신뢰도지수 계산 결과를 제시하였다.