• 한국표면공학회지
• /
• 제53권5호
• /
• pp.227-231
• /
• 2020

This article investigated the effects of stainless steel plate-patterns bonded to aluminum frypan on the thermal distortion and surface temperature of the frypan during gas or induction heating. Two different stainless steel plate-patterns were employed: type A contains only circular holes and type B has not only circular holes but also vacant spaces of 0.5 mm thick and 40 mm long straight line crossing 60 mm long curved line. The bottom of the frypan was distorted during heating when type A stainless steel plate-bonded frypan while no significant thermal distortion was observed for type B stainless steel plate-bonded frypan during heating. Temperature of the frypan surface showed the same trend during gas heating, irrespective of stainless steel plate-patterns. During induction heating, however, the frypan with type B stainless steel plate-pattern showed lower surface temperature than the frypan with type A stainless steel plate-pattern. It is concluded that Type B stainless steel plate-pattern with circular holes and vacant spaces of lines is very effective for minimizing a thermal distortion and lowering the surface temperature of an aluminum frypan during induction heating.

• 한국정밀공학회지
• /
• 제8권4호
• /
• pp.33-40
• /
• 1991

The decrease in surface roughness of work roll and steel strip in cold rolling of low carbon steel strip has been investigated by working distance, materials, total separating force and total reduction ratio. The main results are as follows; For the same lubricating conditions. 1) The changing of surface roughness of steel strip were similar to work roll. The transcription ratio is in inverse proportion to the carbon content of steel strip. 2) The surface roughness of steel strip is hardly change according to changing of total separating force and total reduction ration. 3) The wear of work rolls surface is more rapid in that case of continuous casted steel strip than ingot casted steel strip. The aluminium content dull powder adhere on the rolls surface, and so. It makes the mirror surface of work roll accelerate.

• Steel and Composite Structures
• /
• 제18권6호
• /
• pp.1479-1492
• /
• 2015

This study evaluated the localized stress condition of the real corroded deck surface of an orthotropic steel bridge because severe corrosion damage on the deck surface and fatigue cracking were reported. Thus, a three-dimensional finite element (FE) analysis model was created based on measurements of the corroded orthotropic steel deck surface to examine the stress level dependence on the corrosion condition. Based on the FE analysis results, it could be confirmed that a high stress concentration and irregular stress distribution can develop on the deck surface. The stress level was also increased by approximately 1.3-1.5 times as a result of the irregular corroded surface. It was concluded that this stress concentration could increase the possibility of fatigue cracking in the deck surface because of the surface roughness of the orthotropic steel bridge deck.

• 한국표면공학회지
• /
• 제34권4호
• /
• pp.327-336
• /
• 2001

The skinpassing conditions such as roll type, roll force and roll roughness of the work roll were evaluated to give the surface properties of the galvanized steel sheets that were required for automotive and to get rid of the surface defects that caused with the bad control of galvanized coating process parameters. The surface defects of the galvanized steel sheets such as the ripple mark and the scratch were completely removed as the roll force of SPM work roll was increased and the amount of the transfer of roll surface texture to the strip was also gained a lot. The image clarity of electro discharge textured (EDT) coated steel sheets before and after painting was higher than that of the bright (BRT) and shot blasted (SBT) coated steel sheets because of higher PPI value, lower waviness and uniform surface pattern. Since micro-craters transferred on the surface of the galvanized steel sheets played a role of nucleation sites of chromate reaction, Increase of micro-craters was bring to better corrosion resistance with the increase of the roll force and the use of EDT roll at the skin pass mill.

• 소성∙가공
• /
• 제17권6호
• /
• pp.401-406
• /
• 2008

The frictional behavior of stamping process is a function of interface parameters such as sheet and tool material, lubricant, surface roughness, contact pressure, sliding speed etc. Among these parameters the thing that can be controlled by a steel maker is the surface roughness of sheet. In this study, effects of surface roughness on the frictional behavior of steel sheet for automotive were investigated to find out the way to improve the frictional characteristics of steel sheet. The cold rolled steel sheets with various surface roughnesses were prepared for the test. The flat type friction test was conducted with different lubricant conditions. The surface roughness effect on frictional behavior depends on the viscosity of lubricant. The frictional characteristic of steel sheet was influenced by the amplitude of roughness as well as the shape of that.

• 한국염색가공학회지
• /
• 제34권2호
• /
• pp.102-108
• /
• 2022

The physicochemical properties of stainless steel fibers which were modified by oxygen plasma treatment were analyzed through microscopy and XPS analysis. The wettability of the surface of the stainless steel fiber was observed by measuring water contact angle to find out the effect of the plasma treatment time on the surface characteristics of the stainless steel fiber. In addition, in order to understand the effect of oxygen plasma treatment on the deterioration of the stainless steel fiber properties, the physical properties due to plasma treatment was investigated by measuring the weight reduction, tensile strength, elongation, tensile modulus of the stainless steel fibers according to the treatment time. As a result, the stainless steel fiber surface was etched by the oxygen plasma and the surface became more wettable by the introduction of hydrophilic functional groups. However the physical properties of the stainless steel fiber were not significantly deteriorated even if the surface of the stainless steel fiber made hydrophilic.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.324-324
• /
• 2006

Nb and Ti were added to 316 stainless steel, and then heat-treatments and surface treatments were performed on the 316 stainless steel and the Nb- and Ti-added alloys. All samples indicated enhanced electrical conductivity after surface treatments, whereas they showed low electrical conductivity before surface treatments due to the existence of non-conductive passive film on the alloy surface. In particular, the Hb- and Ti-added alloys showed remarkable enhancement of electrical conductivity compared to the original alloy, 316 stainless steel. Surface characterization revealed that small carbide particles formed on the alloy surface after surface treatments, while the alloys indicated flat surface structure before surface treatments. $Cr_{23}C_6$ mainly formed on the 316 stainless steel, and NbC and TiC mainly formed on the Nb- and Ti-added alloys, respectively. We attribute the enhanced electrical conductivity after surface treatments to the formation of these carbide particles, possibly acting as a means of electro-conductive channel through the passive film. Furthermore, NbC and TiC are supposed to be more effective carbides than $Cr_{23}C_6$ as electro-conductive channels of stainless steel

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.36-43
• /
• 1998

Surface roughness of cold rolled steel sheet as well as the coating technique itself is quite important in obtaining high image clarity of electronic products and car outer panels. Especially, surface characteristics of steel sheet have acquired increasing attention from the steel and automotive industries. While the influence of such characteristics on paintability formability and painted surface appearance is important in defining steel surface requirements for automotive industries. Therefore this paper is dedicated primarily to the issue of paint appearance and reviews for improvement of roughness and peak count about the surface of work roll for the actual temper mill. The conclusions were obtained as follows ; 1) Roughness and peak count about the surface of steel sheet is strongly affected by surface condition of work roll. 2) The electro-discharge textured roll has more uniform roughness distribution than shot blasted roll and it's painted appearance of steel sheet has more improvement than that of the shot blasted because it has more harmonic wave roughness, and the higher peak count of surface roughness.

• Corrosion Science and Technology
• /
• 제13권5호
• /
• pp.163-169
• /
• 2014

The corrosion resistance of epoxy-coated carbon steel was evaluated. The carbon steel surface was subjected to different treatment methods such as steel grit blasting and power tool treatment as well as contamination of water soluble salt. To study the effect of the surface treatments and contamination, the topology of the treated surface was observed by confocal microscopy and a pull-off adhesion test was conducted. The corrosion resistance of the epoxy-coated carbon steel was further examined by electrochemical impedance spectroscopy (EIS) combined with immersion test of 3.5 wt% of NaCl solution. Consequently, the surface contamination by sodium chloride with $16mg/m^2$, $48mg/m^2$ and $96mg/m^2$ didn't affect the adhesion strength for current epoxy coated carbon steel and blister and rust were not observed on the surface of epoxy coating contaminated by various concentration of sodium chloride after 20 weeks of immersion in 3.5 wt% NaCl aqueous solutions. In addition, the results of EIS test showed that the epoxy-coated carbon steel treated with steel grit blasting and power tool showed similar corrosion protection performance and surface cleanness such as Sa 3 and Sa 2.5 didn't affect the corrosion protectiveness of epoxy coated carbon steel.

• Corrosion Science and Technology
• /
• 제20권1호
• /
• pp.7-14
• /
• 2021

PosMAC^® is a brand of Zn-Mg-Al hot-dip coated steel sheet developed by POSCO. PosMAC^® can form dense surface oxides in corrosive environments, providing advanced corrosion resistance compared to traditional Zn coatings such as GI and GA. PosMAC^® 3.0 is available for construction and solar energy systems in severe outdoor environments. PosMAC^®1.5 has better surface quality. It is suitable for automotive and home appliances. Compared to GI and GA, PosMAC^® shows significantly less weight reduction due to corrosion, even with a lower coating thickness. Thin coating of PosMAC^® provides advanced quality and productivity in arc welding applications due to its less generation of Zn fume and spatters. In repeated friction tests, PosMAC^® showed lower surface friction coefficient than conventional coatings such as GA, GI, and lubricant film coated GA. Industrial demand for PosMAC^® steel is expected to increase in the near future due to benefits of anti-corrosion and robust application performance of PosMAC^® steel.