• Structural Engineering and Mechanics
• /
• 제37권1호
• /
• pp.111-129
• /
• 2011

This paper presents a nonlinear analysis of reinforced concrete column with lap splice confined by FRP wrapping in the critical hinging zone. The steel stress-slip model derived from the tri-uniform bond stress model presented in the companion paper is included in the nonlinear frame analysis to simulate the response of reinforced concrete columns subjected to cyclic displacement reversals. The nonlinear modeling is based on a fiber discretization of an RC column section. Each fiber is modeled as either nonlinear concrete or steel spring, whose load-deformation characteristics are calculated from the section of fiber and material properties. The steel spring that models the reinforcing bars consists of three sub-springs, i.e., steel bar sub-spring, lap splice spring, and anchorage bond-slip spring connected in series from top to bottom. By combining the steel stress versus slip of the lap splice, the stress-deformation of steel bar and the steel stress-slip of bars anchored into the footing, the nonlinear steel spring model is derived. The analytical responses are found to be close to experimental ones. The analysis without lap splice springs included may result in an erroneous overestimation in the strength and ductility of columns.

• Journal of Welding and Joining
• /
• 제14권3호
• /
• pp.48-57
• /
• 1996

A study was made to examine the characteristics of base metal and stress relief cracking(SRC) of heat affected zone(HAZ) for HY-100 and Cu-bearing HSLA-100 steels. The Gleeble thermal/mechanical simulator was used to simulate the SRC/HAZ. The details of mechanical properties of base plate and SRC tested specimens were studied by impact test, optical microscopy and scanning electron microscopy. The specimens were aged at $650^{\circ}C$ for HSLA-100 steel and at $660^{\circ}C$ for HY-100 steel and thermal cycled from $1350^{\circ}C$ to $25^{\circ}C$ with a cooling time of $\Delta$t_${800^{circ}C/500^{circ}C}$=21sec. corresponds to the heat input of 30kJ/cm. The thermal cycled specimens were stressed to a predetermined level of 248~600MPa and then reheated to the stress relief temperatures of $570~620^{\circ}C$. The time to failure$(t_f)$ at a given stress level was used as a measure of SRC susceptibility. The strength, elongation and impact toughness of base plate were greater in HSLA-100 steel than in HY-100 steel. The time to failure was decreased with increasing temperature and/or stress. HSLA-100 steel was more susceptible to stress relief cracking than HY-100 steel under same conditions. It is thought to be resulted from the precipitation of $\varepsilon$-Cu phase by dynamic self diffusion of solute atoms. By the precipitation of $\varepsilon$-Cu phase, the differential strengthening of grain interior relative to grain boundary may be greater in the Cu-bearing HSLA-100 steel than in HY-100 steel. Therefore, greater strain concentration at grain boundary of HSLA-100 steel results in the increased SRC susceptibility. The activation energies for SRC of HSLA-100 steel are 103.9kcal/mal for 387MPa and 87.6kcal/mol for 437MPa and that of HY-100 steel is 129.2kcal/mol for 437MPa.

• Steel and Composite Structures
• /
• 제14권3호
• /
• pp.243-265
• /
• 2013

Distortional and local buckling are important factors that influences the bearing capacity of steel-concrete composite box-beam. Through theoretical analysis of distortional buckling forms, a stability analysis calculation model of composite box beam considering rotation of steel beam top flange is presented. The critical bending moment calculation formula of distortional buckling is established. In addition, mechanical behaviors of a steel beam web in the negative moment zone subjected separately to bending stress, shear stress and combined stress are investigated. Elastic buckling factors of steel web under different stress conditions are calculated. On the basis of local buckling analysis results, a limiting value for height-to thickness ratio of a steel web in the elastic stage is proposed. Numerical examples are presented to verify the proposed models.

• 소성∙가공
• /
• 제16권4호
• /
• pp.323-328
• /
• 2007

The residual stress in axial direction of the steel wires has been measured by using a method based on the combination of the focused ion beam(FIB) milling and digital image correlation(DIC) program. The residual stress is calculated from the measured displacement field before and after the introduction of a slot along the steel wires. The displacement is obtained by the digital correlation analysis of high-resolution scanning electron micrographs, while the slot is introduced by FIB milling with low energy beam. The experimental procedures are described and the feasibilities are demonstrated in steel wires fabricated with different conditions. It reveals that the tensile residual stress is formed in all steel wires and this is strongly influenced by the fabrication conditions.

• Steel and Composite Structures
• /
• 제38권5호
• /
• pp.563-582
• /
• 2021

The present study experimentally and analytically investigated the push-out behaviour of H-shaped steel section embedded in ultrahigh-performance fibre-reinforced concrete (UHPFRC). The effect of significant parameters such as the concrete types, fibre content, embedded steel length, transverse reinforcement ratio and concrete cover on the bond stress, development of bond stress along the embedded length and failure mechanism has been reported. The test results show that the bond slip behaviour of steel-UHPFRC is different from the bond slip behaviour of steel-normal concrete and steel-high strength concrete. The bond-slip curves of steel-normal concrete and steel-high strength concrete exhibit brittle behaviour, and the bond strength decreases rapidly after reaching the peak load, with a residual bond strength of approximately one-half of the peak bond strength. The bond-slip curves of steel-UHPFRC show an obvious ductility, which exhibits a unique displacement pseudoplastic effect. The residual bond strength can still reach from 80% to 90% of the peak bond strength. Compared to steel-normal concrete, the transverse confinement of stirrups has a limited effect on the bond strength in the steel-UHPFRC substrate, but a higher stirrup ratio can improve cracking resistance. The experimental campaign quantifies the local bond stress development and finds that the strain distribution in steel follows an exponential rule along the steel embedded length. Based on the theory of mean bond and local bond stress, the present study proposes empirical approaches to predict the ultimate and residual bond resistance with satisfactory precision. The research findings serve to explain the interface bond mechanism between UHPFRC and steel, which is significant for the design of steel-UHPFRC composite structures and verify the feasibility of eliminating longitudinal rebars and stirrups by using UHPFRC in composite columns.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.241-245
• /
• 2007

The residual stress in axial stress in the axial direction of the steel filaments has been measured by using a method based on the combination of the focused ion beam (FIB) and high resolution strain mapping program (VIC-2D). That is, the residual stress was calculated from the measured displacement field before and after the introduction of a slot along the steel filaments. The displacement was obtained by the digital correlation analysis of high-resolution scanning electron micrographs, while the slot was introduced by FIB milling with low energy beam. The present measurement revealed that the residual stress within 8% of the magnitude was persistent in the steel filaments fabricated.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회 논문집(I)
• /
• pp.315-320
• /
• 1998

The experimental set-up and one-dimensional analytical model have been developed to investigate the tensile behavior of reinforced concrete member due to restrained drying shrinkage. The experimental results have been compared with the analytical prediction of the maximum residual stress of steel and concrete due to restrained shrinkage. The tensile residual stress concrete by one-dimensional bilinear model shows 0.19 and 0.63 of tensile strength for 0.83% and 3.29 of steel ratio. The residual tensile stress of concrete increases as the steel ratio increases. The effect of steel fiber has not influenced the residual stress due to restrained shrinkage of concrete.

• 콘크리트학회논문집
• /
• 제15권4호
• /
• pp.585-593
• /
• 2003

본 연구는 외부 프리스트레싱으로 보강된 철근콘크리트 보에 관한 문헌연구와 프리스트레싱 강재의 극한응력 예측식의 개발, 극한응력에 영향을 미치는 변수들에 대한 실험 등이다. 새로운 통합 예측식 개발을 위하여 비부착 프리스트레싱 강재의 극한응력에 대한 ACI 시방식을 확장하고 분석하였다. 본 논문에서는 외부 프리스트레싱 강재의 극한응력에 대한 새로운 합리적 예측식을 제안하고 있는데, 프리스트레싱 강재와 중립축의 깊이 비의 함수로서 표현하여 내부 철근의 영향을 고려하고 있다. 실험연구에서는 프리스트레싱 강재의 극한응력에 가장 큰 영향을 미치는 실험변수를 가지고 외부 프리스트레싱으로 보강된 철근콘크리트 보를 제작하여 실험하였다. 실험연구에서 채택한 영향인자들은 배부철근비, 외부 프리스트레싱 강재비, 지간과 PS강재높이 비 등이다. 실험결과는 분석되어 외부 프리스트레싱 강재의 극한응력에 대한 제안된 예측식의 합리성과 적용성을 확인하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제16권3호
• /
• pp.41-50
• /
• 2012

강재의 품질향상으로 강교에 있어서 재료자체의 파괴보다는 반복하중에 의한 피로균열 문제가 더욱 중요한 요소가 되었다. 재료의 항복으로 인한 교량의 붕괴 등의 사례는 거의 보고되고 있지 않지만 용접부에 발생하는 피로균열에 대한 사례는 매우 많이 보고되고 있다. 종리브와 횡리브, 데크 플레이트로 구성된 직교이방성 강바닥판의 피로응력은 강바닥판을 구성하는 요소들의 구성 형태 및 물성과 밀접한 관련이 있다. 본 논문에서는 Pelikan-Esslinger method와 signed Von-Mises 등가응력 개념을 활용하여 직교이방성 강바닥판의 피로응력을 산정하는 방법을 제시하고, 직교이방성 강바닥판 구성요소들의 구성형태와 물성을 변화시켜 피로응력에 미치는 영향을 분석하였다. 직교이방성 강바닥판의 피로응력과 구성요소의 상관관계 경향을 분석함으로써 설계 및 유지보수 시에 더 효율적인 대안을 찾는데 도움이 될 수 있을 것이다.

• Computers and Concrete
• /
• 제26권6호
• /
• pp.515-531
• /
• 2020

Due to the construction difficulties of steel reinforced concrete (SRC), a new composite structure of steel and steel fiber reinforced concrete (SSFRC) is proposed for solving construction problems of SRC. This paper aims to investigate the bond properties and composition of interfacial bond stress between steel and steel fiber reinforced concrete. Considering the design parameters of section type, steel fiber ratio, interface embedded length and concrete cover thickness, a total of 36 specimens were fabricated. The bond properties of specimens were studied, and three different methods of calculating interfacial bond stress were analyzed. The results show: relative slip first occurs at the free end; Bearing capacity of specimens increases with the increase of interface embedded length. While the larger interface embedded length is, the smaller the average bond strength is. The average bond strength increases with the increase of concrete cover thickness and steel fiber ratio. And calculation method 3 proposed in this paper can not only reasonably explain the hardening stage after the loading end curve yielding, but also can be applied to steel reinforced high-strength concrete (SRHC) and steel reinforced recycled coarse aggregate concrete (SRRAC).