• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.516-528
• /
• 2009

Form the application of long rail system the non-ballast steel plate bridges, fatigue strength increase and rail noise reduction can be expected. This is mainly form the reduction of the rail impact at the rail joint locations which already made to behave together from welds. In the high speed rail, application of long rail system is essential because without long rail system, the required serviceability level can not be achieved. But even with this long rail systems, the thermal expansion from the girder can not be absorbed in the normal bearing systems, and these expansion cause between girder and rail. Also unexpected rail buckling and fracture through rail thermal tension may happen. It was found through numerical analysis and field measurement that these problems can be avoided by semi-fixed bearing system. In this study, the benefits of non-ballast plate bridge through long rail system, especially at the point of girder stability, girder stiffness increase and bearing maintenance will be reviewed.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.177-179
• /
• 2005

As rail steel at a crossing area must undergo much higher loading than those at regular railway, Mn-containing casting steel is normally used for its high load-carrying capability and reduced wear rate. However, as these Mn-containing casting steel is tend to have casting defects, manufacturing cost to produce defect-free Mn-containing casting steel becomes quite expensive. Therefore, in order to investigate the possibilities of replacing expensive Mn-containing casting steel with a mild steel with a surface build-up using a Mn-alloyed steel electrode.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.6 s.165
• /
• pp.1039-1047
• /
• 1999

It is necessary to evaluate the fatigue behavior of rail steel under the multi-axial stress state to assure the railway vehicle's safety. For this purpose, the stress analysis to investigate the crack initiation criteria, static failure and fatigue behavior under mixed-mode are performed. The stress analysis results show that the initiation of the transverse fissure depends on the maximum shear stress below the surface. For the mixed mode, the fatigue crack growth behavior which is represented by the projection crack length and comparative S.I.F, ${\Delta}K_v$, shows the more conservative results. Also, its rate is lower than that of the case of the mode I, and this difference decreases with increasing the stress ratio, R.

• Proceedings of the KSR Conference
• /
• 2002.10a
• /
• pp.31-37
• /
• 2002

Rail cars are subject to vibration, impact and wear which can cause severe defects leading to a fatal accident. Thus, they are designed and manufactured in consideration of such factors influencing their service lifetime. Under-frames are composed of steel and support most of load imposed on the car. Steel is very sensitive to corrosive environment and corroded even in a normal service condition. Regular maintenance can Protect steel Parts from corrosion by painting. However, an exposure of defect point to corrosive agents can make corrosion proceed to a considerable depth, which may cause the structure to remain under safety standard. It is necessary to understand corrosion behavior of rail cars in order to estimate unexpected accidents by corrosion.

• Journal of Korean Association for Spatial Structures
• /
• v.10 no.1
• /
• pp.67-74
• /
• 2010

This paper focuses on steel arrays regarding the application of PV system for solar power system, a renewable energy in steel structure stadium that will be built in Korea, by foreign case study. 20 cases of Steel Structure Stadiums applying PV system after 1990 were selected as the main subjects. The 20 cases of Steel Structure Stadiums were categorized by rail systems that were installed to fix PV module. As the result, linear clamping and roof-integrated type among cross rails were 28% of the whole, followed by 17% of rail-fixed type and 11% of module group-fixed type among vertical-fixed types. In addition, linear clamping and roof-integrated type among cross rails were applied in the inside of the stadium while the outside and other parts of stadiums used angle bracket to fix PV module.

• Proceedings of the KSR Conference
• /
• 2003.10b
• /
• pp.163-169
• /
• 2003

In order to develop domestic railway technology, it is necessary that manufacturing technology of turnout should be kept up with update level, because turnout is the core component of high speed railway. Manganese crossing made of high manganese alloy steel is a important component of turnout. So far, this could not have been welded with rail steel due to metallic problem in Korea. However, joint technology hereunder between manganese crossing and rail by using Flash Butt Welding which is developed by Kangwon Railtech Co., Ltd is the state of the art and enable to realize rail continuousness in turnout section, speed up train velocity, reduce maintenance cost, and enhance riding quality.

• Journal of the Korean Society for Railway
• /
• v.3 no.4
• /
• pp.185-193
• /
• 2000

In general, a third rail current collecting shoegear is widely used in the light rail transit system since it is more efficient and economical than an overhead pantograph. Therefore, its specification is prescribed in the Korean standard specifications for the light rail transit for its applications. This paper describes the development of the third rail current collecting shoegears which is suitable to Korean situation and satisfactory to the Korean standard specifications. Two types are developed for the steel wheel and the rubber tyred AGT system, and various experiments are executed. It is found that performance of the third rail current collecting shoegear developed is proved acceptable.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.4
• /
• pp.761-769
• /
• 1994

Actual load acting on rail surface in the track is the combined mode loading due to the contact rolling load of the wheels. To investigate the fracture behavior on rail steel under combined modes I and II, fracture tests were performed by using the test jigs and fracture specimen which were designed by Richard. The analysis results of experimental fracture data were compared with various fracture criteria that have been introduced for determination of the crack propagation direction and the critical stress of fracture of a crack submitted to a mixed mode loading. From the results, it was shown that the actual crack propagation direction of rail steel agree with the crack propagation directions predicted by maximum tangential stress criterion and strain energy density criterion, and that fracture criterion follows principal strain criterion.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1300-1309
• /
• 2010

In the railway bridges, steel plate girder types are preferred due the high stability. Nevertheless, it has been pointed out that this type of bridge has problems such as, structural damages in the rail and girder seat, noise problem due to impact at the rail joint and excessive vibration. This vibration and/or deflection are mainly because insufficient stiffness of steel plate type of bridge. To resolve these problems, PC-Slab composite plate girder type which has simple process and economic cost, is proposed in this study. The static and dynamic experiment is performed by using the production of actual sized PC-Slab and abandoned steel plate girder. The object of this experiment is to verify the fact that girder stiffness increase and structural safety. The result of the experiment is used to analyze the effect of performance improvement of PC composite plate girder type. Using this method, economic rail maintainers, girder stiffness increase, and also speed/ride improvement even for existing rail could be expected by dynamic performance improvement. Additionally noise due to impact, deflection and vibration caused from long rails can be reduced.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.618-625
• /
• 2000

In general, a third rail current collecting shoegear is used widely in the light rail transit system, which is more efficient than overhead pantograph. Therefore, Korean standard specifications for the light rail transit prescribes for the application of it. This paper describes the development of third rail current collecting shoegears, which is suitable to Korean situation and satisfied with Korean standard specifications, Two types are developed for steel wheel AGT system and rubber tyred AGT system, and various experiments are executed.