• Tribology and Lubricants
• /
• 제14권3호
• /
• pp.1-6
• /
• 1998

An experimental study was performed to discover the effect of environmental conditions on the rolling resistance behavior of pure silver and lead coated 52100 bearing steel. Pure silver and lead coatings were produced by a thermal evaporation coating method. Experiments using a thrust ball bearing-typed rolling test-rig were performed under vacuum, dry air and controlled humidity conditions. Results showed that agglomeration of particles were suppressed in vacuum environment and resulted in low and stable rolling resistance by shakedown phenomena. Also, humidity related closely to the agglomeration of particles and the rolling resistance after the failure of coated layer.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2011년도 추계학술논문집 2부
• /
• pp.391-393
• /
• 2011

본 연구에서는 원자력 발전 및 화력 발전소에서 Turbine 운전 시 열교환기 및 콘덴서에 증기를 응축시 열효율을 높여주기 위해 콘덴서 Tube 내에 이물질 및 스케일을 Sponge Ball을 이용하여 자동으로 제거하는 장치로서 콘덴서 튜브 클리닝 시스템(CTCS)에 사용되고 있는 Screen 재료인 Duplex Stainless Steel UNS S31803의 파손사례에 대해 연구하였다. 파손원인 분석은 스크린의 강도해석, 재료의 화학분석시험, 조직시험 및 점용접부의 신뢰성 시험(Peel-off test)으로 수행되었고 저항용접부의 용접 불량 때문에 발생하였을 확인하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.47-54
• /
• 1998

An experimental study was performed to discover the effect of environmental conditions on the rolling resistance behavior of pure silver and lead coated 52100 bearing steel. Pure silver and lead coating were produced by a thermal evaporation coating method. Experiments using a thrust ball bearing-typed rolling test-rig were performed under vacuum, dry air and controlled humidity conditions. Results showed that agglomeration of particles were prevented in vacuum environment and as it showed low and stable rolling resistance by shakedown phenomena. Also, humidity relates closely to the agglomeration of particles and increased the rolling resistance after the failure of coated layer.

• Tribology and Lubricants
• /
• 제21권1호
• /
• pp.16-20
• /
• 2005

Friction and wear characteristics between two steel surfaces under fretting condition are investigated experimentally. The fretting damage caused by low-amplitude oscillatory sliding can be classified into three regimes of gross-slip, mixed-slip and partial-slip due to stick-slip phenomenon. One of the most important characteristics of fretting wear is the transition from gross-slip to mixed-slip. This study was focused on getting the degree of stick-slip out of the friction transition under fretting condition. Fretting wear is divided into three conditions of gross-slip/mixed-slip/partial-slip. The criteria for the division are friction and displacement amplitude, wear scar morphology and dissipated energy. In this test, friction force and displacement were measured for detecting the transition from mixed-slip to gross-slip and qualitatively predicting the degree of the wear.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제25회 춘계학술대회
• /
• pp.101-110
• /
• 1997

An experimental study was performed to discover the tribological behaviors of pure silver coated 52100 bearing steel. Pure silver coatings ranging from 80 nm to several micrometers were produced by a thermal evaporation coating method. Experiments using a thrust ball bearing-typed rolling test-rig were performed for the investigations of the influence of coating thickness on the tribological rolling behavior. The existence of optimum film thickness which revealed minimum rolling resistance was discovered. A careful analysis on the contact surfaces for the optimum film thickness has been performed. The contact patches produced by the transferred silver films played an important role for the rolling resistance to keep low.

• Tribology and Lubricants
• /
• 제19권5호
• /
• pp.274-279
• /
• 2003

$Al-SiC_{p}$ composite layer was prepared by plasma thermal spray on aluminum substrate. The homogeneously dispersed composite powder for thermal spray was fabricated by mechanical alloying with ball mill. The friction tests of the composite layers and commercial aluminum alloys for comparison were performed in the temperature range of 20∼$260^{\circ}C$ with the interval of $40^{\circ}C$ with steel counter-face. Friction coefficient was recorded during test sequence, and the microstructure of surface and debris was investigated by optical and scanning electron microscope. Friction coefficients of composite and aluminum alloys at room temperature were similar except pure aluminum. As the temperature increase, friction coefficient was increased rapidly in AC4C, AC2A. But friction coefficient of $Al-SiC_{p}$ composite was not increased so much up to $220^{\circ}C$. Consequently, the reinforcement of $SiC_{p}$ into aluminum matrix increased the stability of friction coefficient as well as wear resistance.

• Tribology and Lubricants
• /
• 제11권1호
• /
• pp.37-43
• /
• 1995

Sputtering parameters such as N$_{2}$ flow percentage and bias voltage in reactive TiN film deposition by RF magnetron sputtering system were selected to investigate the effects of sputtering deposition conditions on tribological characteristics of TiN films. Wear scar of the steel ball damaged by TiN films was measured by SEM to understand wear behavior of deposited TiN films. Crystallization and induced strain of TiN were detected by XRD. Wear mode changed from plastic to brittle with increasing N$_{2}$ ratio. Wear scar by sliding with TiN film deposited at around 27% N$_{2}$ ratio was maximum. The results indicate that bias voltage affects tribological behavior by formation of high density film and internal stress.

• Tribology and Lubricants
• /
• 제14권1호
• /
• pp.1-6
• /
• 1998

An experimental study was performed to discover the tribological behaviors of pure tin and zinc coated 52100 bearing steel. Pure tin coatings ranging from 30 nm to 30,000 nm and pure zinc coatings ranging from 500 nm to 52,000 nm were produced by a thermal evaporation coating method. Experiments using a thrust ball bearing-typed rolling test-rig were performed for the investigations of the effect of coating thickness on the tribological rolling behavior. Results showed that the existence of optimum film thickness which revealed minimum rolling resistance was discovered for tin and zinc coating. The compatibility of coating material to iron showed no significant effect on the rolling resistance behavior. The hardness of coating material revealed significant influence to the rolling resistance behavior.

• 대한기계학회논문집
• /
• 제19권3호
• /
• pp.623-630
• /
• 1995

The impulse response functions (force-strain relations) for Euler-Bernoulli and Timoshenko beams are considered. The response of a beam to a transverse impact force is numerically obtained with the convolution approach using the impulse response function obtained by Laplace transform. Using this relation, the impact force history is determined in the time domain and results are compared with those from Hertz's contact law. The parameters of timpact force model are identified using the recovered force and compared with the Hertz's contact model. In order to verify the proposed algorithm, measurements were done using an impact hammer and a steel ball drop test and these results are also compared with the simulated values.

• 한국정밀공학회지
• /
• 제7권4호
• /
• pp.29-39
• /
• 1990

The purpose of this research is to analyze the impact behaviors of laminated composite plates subjected to the transverse low-velocity impact by the steel ball. A plate finite element model based on Whitney and Pagano's the first-order shear deformation theory (FSDT) in conjunction with experimental static contact laws is formulated and then compared with the results of the impact experiments. Because the input data and the output data printed at every integration time step are lots of amount, these are interactively poecessed by the developed pre-processor(PREPLOT) and postprecessor(POSTPLOT). All results from these procesors are automatically generated by CALCOMP plotter. Test materials are glass/expoxy composite materials. The specimens are composed of [$0^{\circ} /45^{\circ}/0^{\circ}/-45^{\circ}/0^{\circ}/]2s\ and \[90^{\circ}/45^{\circ}/90^{\circ}/-45^{\circ}/90^{\circ}/$]2s stacking sequences and have $4.5^t{\times}200^w{\times}200^l$(mm) and $4.5^t{\times}300^w{\times}300^l$(mm) dimensions.