• Journal of the Korean Institute of Gas
• /
• v.17 no.2
• /
• pp.70-77
• /
• 2013

The present study has been carried out to analyze the effect of steam hammering on the steam piping system including the final superheater, the high pressure turbine, check valve and the first reheater by sudden stoping of main stop valve in a power plant. For the present steam hammering analysis, the well known Flowmaster software has been used to model the steam piping system and the time dependent characteristics of pressure and steam mass flow rate has been conducted. Using the result of the unsteady pressure and steam mass flow rate, the forces acting on the elbows in the piping system has been derived. From the present analysis, it has been elucidated that the elbow just before the main stop valve and the elbow near the connection pipe between bypass pipe and check valve had the largest force among the elbows in the steam piping system. The structural safety diagnostics study on the elbow and the supporting structures of the steam piping system of a power plant will be conducted in the future by the present results of the forces acting on the elbow.

• International Journal of Fluid Machinery and Systems
• /
• v.9 no.1
• /
• pp.85-94
• /
• 2016

An experimental study is conducted for unsteady wet steam flow in a four-stage low-pressure test steam turbine. The measurements are carried out at outlets of the last two stages by using a newly developed fast response aerodynamic probe. This FRAP-HTH probe (Fast Response Aerodynamic Probe - High Temperature Heated) has a miniature high-power cartridge heater with an active control system to heat the probe tip, allowing it to be applied to wet steam measurements. The phase-locked average results obtained with a sampling frequency of 200 kHz clarify the flow characteristics, such as the blade wakes and secondary vortexes, downstream from the individual rotational blades in the wet steam environment.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2174-2179
• /
• 2003

For many years, T/G Supplier has constructed a number of thermal power plants and researched to improve the performance and the reliability of steam turbine, which are achieved by advances in design and materials technology. In recent, interest is renewed in advanced steam condition as means of improving economy of thermal power plant and reducing environmental pollution. Improvements in the maximum power have been driven by the development of advanced rotor and bucket material and longer last stage bucket. Improvements in efficiency have been brought through advances in mechanical efficiency and thermodynamic efficiency. This paper describes a number of new steam path design features introduced to the steam turbine product. And also this paper describes new design technologies' development, new technologies' trend and technologies' development for ultra-super critical steam turbine.

• Corrosion Science and Technology
• /
• v.20 no.1
• /
• pp.22-25
• /
• 2021

In the past, Alloy 600 nickel-based alloys have been widely used in steam generators. However, most of them have been replaced by thermally treated alloy 690 tubes in recent years because mill annealed alloy 600 materials are known to be susceptible to stress corrosion cracking. Unlike this general perception, some steam generators using mill annealed alloy 600 tubes show excellent performance even though they are designed, manufactured, and operated in the same way. Therefore, various analyses were carried out to determine causes for the degradation of steam generators. Based on the general stress corrosion cracking mechanism, tube material susceptibility, residual stress, and sludge deposits of steam generators were compared to identify factors affecting stress corrosion cracking. It was found that mill annealed alloy 600 steam generator tubes showed higher resistance to stress corrosion cracking when the amount of sludge deposits on tube surface was smaller and residual stress generated during the fabrication was lower.

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2260-2262
• /
• 2004

After steam turbines in power plant drives generator and maintains it at rated speed using high temperature and high pressure steam energy, they regulate the output of generator when synchronized in parallel with the power system. By the way, as the steam flow into turbine can not be reduced fast even though the electrical load is lost, the turbine gets into dangerous situation due to the increase of its speed. At this time, the duty of the turbine governor is "how to limit the speed within its overspeed trip setpoint and escape from danger." For the purpose of it, there are various ways known. Some overspeed protection methods for steam turbines now being operating in korea are introduced in this paper.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.2
• /
• pp.103-111
• /
• 2019

The combined cycle plant is an integration of gas turbine and steam turbine, combining the advantages of both cycles. It recovers the heat energy from gas turbine exhaust to use it to generate steam. The heat recovery steam generator plays a crucial role in combined cycle plants, providing the link between the gas turbine and the steam turbine. Simulation of the performance of the HRSG is required to study its effect on the entire cycle and system. Computational fluid dynamics has potential to become a useful to validate the performance of the HRSG. In this study a solver has been implemented in the open source code, OpenFOAM, for combustion simulation in the heat recovery steam generator. The solver is based on the steady laminar flamelet model to simulate detailed chemical reaction mechanism. Thereafter, the solver is used for simulation of HRSG system. Three cases with varying fuel injections and gas turbine exhaust gas flow rates were simulated and the results were compared with measurements at the system outlet. Predicted temperature and emissions and those from measurements showed the same trend and in quantitative agreement.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1015-1019
• /
• 2001

There are several bearing systems at the large steam-turbines in thermal power plant. The bearing system is one of the most important parts of rotating machinery. The steam turbine vibrations mainly depend on the bearing oil and the shaft alignment condition. This paper describes on the steam turbine abnormal vibration due to the oil whip in terms of the shaft alignment in the thermal power plant.

• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.3
• /
• pp.409-413
• /
• 2016

The 500 MW rated steam turbine model in coal fired power plant is developed to be used for validation and verification of controller rather than for the education of operator. The valve, steam turbine, reheater and generator are modeled and integrated into the simulator. And the data from the plant heat balance diagram are used for estimation of the model parameters together with actual operating data. It is found that the outputs of model such as pressure, temperature and speed are similar to the operating ones. So, it is expected that the developed model will play a very big role in controller development.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.9 no.1
• /
• pp.40-47
• /
• 2013

The capacity factor of nuclear power plant in Korea is the highest level in the world. However, the integrity assessment of nuclear power plant is depended on foreign country. Especially, most eddy current testing systems for inspecting steam generators in nuclear power plant are currently imported from USA, Canada, and so on. Therefore, the eddy current testing system can react more active and adaptive from economic and managerial standpoint for actual nuclear power plants in Korea is required. In this paper, an eddy current testing system for inspecting steam generators in nuclear power plants is introduced. Frequency generator, analog circuit, analog digital converter circuit, and digital control circuit are composed in eddy current testing system. A benchmarking of acquisition system and acquisition software, eddynet 11i made by Zetec, and modifications are carried out based on the test environment of Korea nuclear power plants. Finally, all eddy current apparatus are integrated to inspect steam generator tubes in nuclear power plants.

• Journal of the Korean Society of Tobacco Science
• /
• v.17 no.2
• /
• pp.139-148
• /
• 1995

This study was carried out to investigate the effects of super heated steam on the physical and chemical changes of burley cut tobacco. Total sugar, total alkaloid, ether extracts, crude ash, total nitrogen and pH for leaf chemical constituents were analyzed. Filling power and fineness index for physical properties, and carbonyl compounds, phenol compounds, amonia, pH, hydrogen cyanide nicotine, carbon monoxide, total volatile base and tar for smoke components were also analyzed. The cut tobacco treated with super heated steam showed significant decrease in total sugar and total alkaloid. The filling power of the sample treated with the super heated steam system was increased abruptly when heated at over 250℃. The fineness index showed similar tendency to that of common toast method. Super heated steam treatment slightly decreased carbonyl compounds, phenol compounds, hydrogen cyanide, nicotine, carbon monoxide and tar in the tobacco. Especially the decrease of ammonia was the most remarkable. The pH of smoke was a little different compared with that in the common toast. The sensory test results showed that, compared to the common conveyer moving system, the tobacco treated with super heated steam system brought out more roasted flavor, lowered impact, irritation, and sting, further improved aftertaste, and lowered bitterness. The super heated steam treatment method used in the studies is expected to give better filling power, mild taste and toasted odor of tobacco than that of the common method for toast treatment. Key words : burley tobacco, super heated steam, expansion, toast.