• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.103-106
• /
• 2006

The Plate reformer consisting of combustion chamber and reforming chamber for 25 kW MCFC stack has been operated and computational fluid dynamics was applied to estimate reactions and thermal fluid behavior in the reformer. The methane air 2-stage reaction was assumed in the combustion chamber, and three step steam reforming reactions were included in the calculation. Flow uniformity, reaction rate and species distribution, and temperature distribution were analyzed. In particular, temperature distribution was compared with the measurements to show good agreement in the combustion chamber, however, inappropriate agreement in the reformer chamber

• 전기학회논문지
• /
• 제59권1호
• /
• pp.152-159
• /
• 2010

This paper describes the actual application of a feedback control loop as a means for minimizing turbine impulse chamber pressure variation during the turbine steam valve tests at a 1,000 MW nuclear power plant. The chamber pressure control loop was implemented in the new digital control system which was installed as a replacement for the old analog type control system. There has been about 40MW of the generator output change during the steam valve tests, especially the high pressure governing valve tests, because the old control system had not the impulse chamber pressure control so the operators had to compensate steam flow drop manually. The process of each valve test consists of a closing process and an reopening process and the operators can make sure that the valves are in their sound conditions by checking the valves movement. The control algorithm described in this paper contributed to keep the change in megawatt only to 6MW during the steam valve tests. Thereby, the disturbance to reactor control was reduced, and the overall plant control system's stability was greatly improved as well.

• 농업과학연구
• /
• 제45권4호
• /
• pp.695-706
• /
• 2018

This study was conducted to investigate the effect of a steam chamber type on the ruminal fermentable characteristics and nutrient degradabilities of corn flakes in Hanwoo. Three Hanwoo equipped with a ruminal fistula were used as experimental animals. There were two treatments: Corn flake using a steam chamber (CFSC, 1.0 atm - $100^{\circ}C$ 96 min) or corn flake using a pressurized steam chamber (CFPSC, 1.5 atm - $111^{\circ}C$ 12 min), respectively. In the in vitro trial, the ruminal pH was significantly lower in the CFPSC than in the CFSC (p < 0.01). The ammonia concentration was increased by 14.1% in the CFPSC compared to the CFSC (p < 0.05). The concentration of acetic acid was higher in the CFSC than in the CFPSC (p < 0.01). The concentrations of propionate, butyrate and total-VFA at 24 and 48 h were higher in the CFPSC than in the CFSC (p < 0.05). In the in situ trial, the degradability of dry matter was significantly higher in the CFSC than in the CFSC (p < 0.01). In addition, the degradabilities of starch and crude protein were significantly higher in the CFSC than in the CFSC (p < 0.01). Thus, the present results indicate that the pressurized steam chamber could be recommended to improve the feed value of corn flake according to the increase in the starch degradability and volatile fatty acid production.

• Journal of Advanced Marine Engineering and Technology
• /
• 제11권3호
• /
• pp.53-60
• /
• 1987

Steam ejector is a equipment which compresses the gases to desired discharge pressure. It is widely used for the evacuation systems because of its high working confidence. And recently it is used as the thermo-compressors in the various energy saving systems. Steam ejector is constructed of three basic parts; a suction chamber, a motive nozzle and a diffuser. The high velocity stream jet of steam emitted by the motive nozzle creats suction chamber, which draws the low pressure gases. The diffuser converts the kinetic energy of high velocity flow to pressure energy. It is not easy to determine the dimensions of a steam ejector met to the desired design condition, because that the expected suction rates must be obtained by reapeating the complicate calculation. And also such a calculation is concomitant with geometrical analysis for suction part and diffuser based on the stability of steam flow. Therefore, it is considered that the Computer-Aided Design (CAD) of steam ejector is a powerful design method. In this paper, computer program for steam ejector design is developed based on the theoretical research and the previous experimental results. And the determinating method of diffuser inlet angle and the velocity development profile of suction gas along to the diffuser are suggested. The validity of the development profile of suction gas along to the diffuser are suggested. The validity of the developed computer results with other's for the practical design calculation of a manufactured steam ejector.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.441-444
• /
• 2006

Extrusion molding concrete panel is cured two times, that is the steam curing at atmospheric pressure and a high-pressure steam curing(autoclaving). Steam curing at atmospheric pressure is done before autoclaving and to acquire the proper strength for treat in process. Though this curing is the important factor on the quality of product and the speed in manufacturing process, it was not evaluated properly so far. Because of ignorance about curing, some engineers even think that the dry curing is better than the steam curing. This study is to investigate the properties of specimen according to variation of curing conditions in the coring chamber such as laboratory scale, pilot plant, and commercial plant. As estimating, in case of steam curing at atmospheric pressure to make extrusion molding concrete panel, moisture curing is better than dry curing and the desirable maximum temperature in curing chamber is about $50^{\circ}C$.

• 대한설비공학회지:설비저널
• /
• 제7권2호
• /
• pp.73-79
• /
• 1978

This paper presents the experimental study on the design conditions of pressure between booster ejector and air ejector in the steam-jet water-vapour refrigeration system. In this experiment, the motive steam of booster ejector and ai. ejector was dry saturated from 6 ata to 8 ata and flash chamber pressure were about $10\∼540mmHg$ higher than mixing section in booster ejector. The investigation of air on the pressure of booster ejector was performed by changing the condenser pressure. The experimental results show that flash chamber vacuum and condenser pressure of steam-jet refrigeration cycle increased in accordance with the increase of motive steam Pressure. Among the several nozzle sires tested, No.4 nozzle were best in term of evaporator vacuum under the constant operating conditions of air ejector in condenser.

• Journal of Animal Science and Technology
• /
• 제61권3호
• /
• pp.170-181
• /
• 2019

This study aimed to investigate the effects of temperature and retention time of the pressurized steam chamber on the ruminal fermentation characteristics and nutrient degradability of corn flakes in three Korean native Hanwoo cows and three Holstein cows implanted with a ruminal fistula. Corn kernels were categorized into 13 groups based on the chamber temperature (range, $100^{\circ}C-116^{\circ}C$) and retention time (range, 700-950 s). The pH value was lowest in T1 regardless of breed. Propionate concentration was the highest in T2 (p < 0.05). Total-volatile fatty acid (VFA) concentration was slightly but not significantly greater in T2 than in other conditions. Dry matter (p < 0.05), starch, and crude protein (p < 0.05) degradability were the highest in T1. At different incubation times and with different breeds, dry matter, starch, and crude protein degradability of corn flakes were the highest in T1. Thus, the present results indicate that the optimal temperature and retention time of the pressurized steam chamber should be $100^{\circ}C-105^{\circ}C$ and 700-720 s.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.479-484
• /
• 2000

For the purpose of a cost effective design of practical subsonic/supersonic ejector systems, an experiment was carried out using a superheated steam as a primary driving flow. The superheated steam jet was produced by several different kinds of subsonic and supersonic nozzles. The secondary flow of atmospheric air inside a plenum chamber was drawn into the primary steam jet. The vacuum performance of the plenum chamber was investigated for a wide range of the ejector operation pressure ratio. The result showed that the static pressure of the mixed flow at the ejector throat is only a function of the ejector operation pressure ratio, regardless of the primary nezzle type employed.

• 한국수소및신에너지학회논문집
• /
• 제17권4호
• /
• pp.403-408
• /
• 2006

The plate reformer consisting of combustion chamber and reforming chamber for 25 kW MCFC stack has been operated and computational fluid dynamics was applied to estimate reactions and thermal fluid behavior in the reformer. The methane air 2-stage reaction was assumed in the combustion chamber, and three step steam reforming reactions were included in the calculation. Flow uniformity, reaction rate and species distribution, and temperature distribution were analyzed. In particular, temperature distribution was compared with the measurements to show good agreement in the combustion chamber, however, inappropriate agreement in the reformer chamber.

• 한국추진공학회지
• /
• 제4권4호
• /
• pp.1-8
• /
• 2000

본 연구에서는 아음속/초음속 이젝터 시스템의 효과적인 설계를 목적으로, 증기 보일러로부터 발생하는 파열증기를 1차 구동유체로 하는 축대칭 아음속/초음속 이젝터 유동을 실험하였다. 과열증기는 여러형태의 아음속/초음속 노즐에 의하여 이젝터 혼합부로 방출되도록 설계되었으며, 2차정체실 내부에 있는 대기 공기는 증기제트에 의하여 혼합부로 유입된다. 실험에서는 2차정체실의 진공성능을 조사하기 위하여 넓은 범위의 이젝터 자동압력비에 대하여 적용하였다. 본 연구의 결과로부터 이젝터목에서 혼한유동의 정압은 1차 노즐의 형태에 관계없이 이젝터 작동압력비의 함수만에 의하여 결정된다는 것을 알았다.