• 정보저장시스템학회논문집
• /
• 제1권1호
• /
• pp.67-72
• /
• 2005

This study proposes a design methodology to determine the optimum configurations of the optical flying head (OFH) for near-field recording systems. Since the OFH requires stricter static and dynamic characteristics of slider air-bearings within an optical tilt tolerance over the entire recording band, an optimum design to keep the focusing and tracking ability stable is essential. The desired flying characteristics considered in this study are to minimize the variation in flying height between the SIL and the disk from a target value, satisfying the restriction of the minimum flying height, to keep the pitch and roll angles within an optical tilt tolerance, and to ensure a higher air-bearing stiffness. Simulation results demonstrate the effectiveness of the proposed design methodology by showing that the static and dynamic flying characteristics of the optimally designed OFH are enhanced in comparison with those of the initial. The gap between the SIL and the disk can be kept at less than 100 nm even if the optical tilt tolerance of the SIL is considered.

• 국제초고층학회논문집
• /
• 제8권4호
• /
• pp.265-273
• /
• 2019

The purpose of this review paper is to briefly describe main the features of novel procedures developed by the National of Standards and Technology (NIST) for the design of tall buildings. Topics considered in the paper include: the division of tasks between wind and structural engineers; the determination of wind effects with specified mean recurrence intervals by accounting for wind directionality; the risk-consistent design of structures subjected to multiple wind hazards; iterative dynamic analyses and member sizing, including the use of modern optimization approaches; and commonalities of and differences between Database-assisted Design (DAD) and Equivalent Static Wind Loads procedures. An example of the application of the DAD procedure is presented for a reinforced concrete structure. Also included in the paper is an introduction to ongoing research on the estimation of wind load factors or of augmented design mean recurrence intervals commensurate with the uncertainties in the factors that determine the wind effects.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.333-340
• /
• 2003

In Korea, drilled shaft are generally socketed into rock. Driven pile has environmental problems such as vibration and noise. Therefore, applications of the drilled shaft are increasing in Korea. In this paper, static load test data of the rock socketed drilled shaft at Gwangandaero and Suyeong 3hogyo are analyzed. The bearing capacities from field test data and theoretical formula are compared and analyzed. From this study, design approaches for drilled shafts in Korea are examined and several suggestions are proposed.

• 한국항공우주학회지
• /
• 제30권2호
• /
• pp.115-121
• /
• 2002

본 논문은 KTX-1 기본훈련기 방향타 조종계통의 정적 하중 시험을 요약한 것이다. 방향타 콘트롤 시스템 정적 하중시험은 정하중 구조 시험용 KTX-1 #004호기에 장착 상태에서 실시하였으며 사용되는 모든 부품은 실제와 동일한 것으로 장착하고 정적하중 시험을 실시하였다. 시험하중 조건은 설계 제한하중(Design Limit Load)과 설계 극한하중(Design Ultimate Load)까지 시험을 수행하며, 전방석과 후방석 패달에 동시하중을 작용하는 경우 중복하중계수(Dual Factor)까지 고려하였다. 이 시험의 요구하중은 MIL-A-8855(USAF)의 요구조건에 따라 수행하였으며, 방향타 콘트롤 시스템 시험 결과는 미 군사규격 요구조건을 만족하였다.

• Journal of Electrical Engineering and Technology
• /
• 제13권6호
• /
• pp.2187-2195
• /
• 2018

In order to realize the multi-objective control of single-input multi-output nonlinear differential algebraic system (NDAS) and to improve the dynamic characteristics and static accuracy, a design method of nonlinear control with multi-objective feedback (NCMOF) is proposed, the principium of this method to arrange system poles, as well as its nature to coordinate dynamic characteristics and static accuracy of the system are analyzed in detail. Through NCMOF design method, the multi-objective control of the system is transformed into linear space, and then it is effectively controlled under the nonlinear feedback control law, the problem to balance all control objectives caused by less input and more output of the system thus is solved. Applying NCMOF design method to generator excitation system, the nonlinear excitation control law with terminal voltage, active power and rotor speed as objective outputs is designed. Simulation results show that NCMOF can not only improve the dynamic characteristics of generator, but also damp the mechanical oscillation of a generator in transient process. Moreover, NCMOF can control the terminal voltage of the generator to the setting value with no static error under typical disturbances.

• 한국군사과학기술학회지
• /
• 제9권4호
• /
• pp.15-23
• /
• 2006

In this paper, full-scale airframe static test of 4-seater canard airplane(the Firefly) was explained. From the results of the structural analysis, 5 design limit loads test conditions and 11 design ultimate loads test conditions were selected. Test loads analysis was performed and test fixtures and load control system(LCS) were prepared to realize the test loads. To protect the test article during the test, the overload protection system was prepared. Strain and deflection values were acquired through the data acquisition system(DAS) to verify the structural analysis results.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.552-560
• /
• 2004

Stone column is a soil improvement method and can be applicable for loose sand or weak cohesive soil. Since the lack of sand in Korea, stone column seems one of the most adaptable approach for poor ground as a soil improvement method. However, this method was not studied for practical application. In this paper, the most effective design parameters for the being capacity of stone column were studied. The parametric study of major design factors for single stone column was carried out under the bulging and general shear failure condition, respectively. Especially, a test result of single stone column by static load was compared with the bearing capacity values of suggested formulas. The analysis result showed that the ultimate bearing capacity by the formula was much less than the measured value by the static load test. Especially, the result of the parametric study under general shear failure condition showed that the bearing capacity has apparent difference between each suggested formulas with the variation of the major design parameters. Therefore, the result of this study can be a suggestion which is applicable for the field test and the future research.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2011년도 추계학술대회
• /
• pp.75-84
• /
• 2011

본 논문에서는 지하공간에 설치되는 지중구조물에 대한 내진해석에 관한 연구로 구조물의 거동특성과 내진설계방법의 종류에 따라 수치해석을 실시하였다. 이를 위해 현재 가장 많이 실무에 적용되고 있는 내진설계방법인 등가정적해석법과 응답변위법을 적용하고 정밀한 해석이 가능한 시간이력해석법에 의해 검증을 시행하였으며 구조물 내진해석은 3-D 모델링에 의해 구조물-지반 상호작용을 고려하고 국내의 콘크리트구조설계기준에 따라 수행하였다. 해석 결과 현재 실무에서 적용되고 있는 등가정적해석법과 응답변위법을 적용하는 경우 정밀한 동적해석법 보다 다소 크게 산정되어 실무적용에 문제가 없음을 확인 할 수 있었다.

• 동력기계공학회지
• /
• 제17권4호
• /
• pp.36-44
• /
• 2013

The aerodynamic performance of a cross-flow fan is strongly influenced by the various design factors of a rear-guider and a stabilizer. The design factors considered in this paper are a rear-guider clearance, a stabilizer clearance, and a stabilizer setup angle, respectively. Also, these factors are given to the various diameter ratio between a basic circle and a impeller. The static pressure and the flowrate of a cross-flow fan were measured with a fan-tester. It could be found that the useful design factors with a good aerodynamic performance exist in the certain assembly conditions of an indoor RAC. Therefore, it could be known that a new published patent determining the easy design of an indoor RAC can be applied in a variety of goods.

• Structural Engineering and Mechanics
• /
• 제81권1호
• /
• pp.93-102
• /
• 2022

The optimum design of reinforced concrete cantilever retaining walls subjected to seismic loads is an extremely important challenge in structural and geotechnical engineering, especially in seismic zones. This study proposes an adaptive sperm swarm optimization algorithm (ASSO) for economic design of retaining structure under static and seismic loading. The proposed ASSO algorithm utilizes a time-varying velocity damping factor to provide a fine balance between the explorative and exploitative behavior of the original method. In addition, the new method considers a reasonable velocity limitation to avoid the divergence of the sperm movement. The proposed algorithm is benchmarked with a set of test functions and the results are compared with the standard sperm swarm optimization (SSO) and some other robust metaheuristic from the literature. For seismic optimization of retaining structures, Mononobe-Okabe method is employed for dynamic loading conditions and total construction cost of the structure is considered as the single objective function. The optimization constraints include both geotechnical and structural restrictions and the design variables are the geometrical dimensions of the wall and the amount of steel reinforcement. Finally, optimization of two benchmark retaining structures under static and seismic loads using the ASSO algorithm is presented. According to the numerical results, the ASSO may provide better optimal solutions, and the designs obtained by ASSO have a lower cost by up to 20% compared with some other methods from the literature.