• 한국가구학회지
• /
• 제19권5호
• /
• pp.350-357
• /
• 2008

This research investigates the bending properties to predict the work-energy to maximum load and impact bending energy from static bending and impact bending test. Specimens were prepared from lumber made of thinning crop-trees. Matched specimens were used for MC 12% and green moisture specimens to measure the effect of moisture content on the absorbed energy from static and impact bending tests. The bending properties such as MOE, MOR, etc. is a good predictor to investigate the work-energy and work-energy per unit volume from static bending and impact bending test. The impact bending energy is increased with increasing moisture content. However, the work to maximum load from static bending test is increasing with increasing the MC only for higher density species.

• 한국정밀공학회지
• /
• 제15권12호
• /
• pp.188-193
• /
• 1998

This paper describes static and dynamic weak point analysis of spindle systems to eliminate high concentrated bending point on spindle and improve total stiffness of spindle systems. The weak point analysis is based on the evaluation of bending curves of spindles. For static weak point analysis the bending curve is derived from static deflection curve and for dynamic weak point analysis it is derived from the mode shape curves in consideration of the transfer function at exciting point. The validity of the weak point search methodology is verified by comparison of the static deflection, the natural frequency and the dynamic compliance between the original and the improved spindle.

• Journal of the Korean Wood Science and Technology
• /
• 제25권1호
• /
• pp.8-14
• /
• 1997

Stress wave velocity, wave impedance, and stress wave elasticity of small, clear bending specimens of five domestic softwoods (Pinus densiflora, Pinus koraiensis, Chamaecyparis obtusa, Cryptomeria japonica, and Larix leptolepis) and four tropical hardwoods(Kempas, Malas, Taun, and Terminalia) were correlated with static bending modulus of elasticity(MOE) and modulus of rupture(MOR). The degree of correlation between stress wave parameters and static bending properties was dependent on wood species tested. Stress wave elasticity and wave impedance were better predictors for static bending properties than stress wave velocity for each species individually and for softwood or hardwood species taken as a group, even though elasticity and impedance were nearly equally correlated with static bending properties apparently. Based upon the correlation coefficient between stress wave parameters and static properties, stress wave elasticity and wave impedance were found as stress wave parameters which can be used for the purpose of the reliable and successful prediction of bending properties. The degree of correlation between static MOE and MOR was also different according to wood species tested. Static MOE was nearly as well correlated with MOR as was stress wave elasticity. The results of this research are encouraging and can be considered as a basis for further work using full-size lumber. From the results of this study, it was concluded that stress wave measurements could provide useful predictions of static bending properties and was a feasible method for machine stress grading of domestic softwoods and tropical hardwoods tested in this study.

• Journal of the Korean Wood Science and Technology
• /
• 제33권5호통권133호
• /
• pp.13-20
• /
• 2005

This paper deals with flexural vibration techniques as a means of predicting bending strength properties for quarter-sawn and flat-sawn planes of red pine containing knots. Dynamic modulus of elasticity $(MOE_d)$ was calculated from resonance frequency obtained from the flexural vibration induced by a magnetic driver in quarter-sawn and flat-sawn planes of red pine containing knots. The dynamic MOE were well correlated to bending strength properties. Their correlation coefficients ranged from 0.866 to 0.800 for the regression between dynamic MOE and static bending MOE or MOR. The difference of the values between quarter-sawn and flat-sawn was very small. These values were higher than correlation between percentage of total knot diameter to total width of red pine specimen $(K_T(%))$ as well as $K_O(%)$ base upon ASTM D 3737 and static bending strength properties (correlation coefficient r = 0.448~0.704), and were similar to those between static bending MOE and bending MOR (r = 0.850). These results indicate that dynamic MOE obtained from resonance frequency induced by flexural vibration of magnetic driver is able to effectively use for predicting of static bending strength of red pine containing knots as well as static MOE.

• Journal of the Korean Wood Science and Technology
• /
• 제34권2호
• /
• pp.46-57
• /
• 2006

To estimate nondestructively strength performances of laminated woods, 3-ply parallel- and cross-laminated wood specimens exposed under atmosphere conditions after bending creep test were prepared for this study. The effects of density of species, arrangement of laminae and lamination types on dynamic MOE obtained by flexural vibration were investigated, and regression analyses were conducted in order to estimate static bending strength and bending creep performances. Dynamic MOE of parallel-laminated woods showed 1.0~1.2 times higher values than static bending MOE, and those of cross-laminated woods showed 1.0~1.4 times higher values than static bending MOE. The degree of anisotropy of dynamic MOE perpendicular to the grain of face laminae versus that parallel to the grain of face laminae was markedly decreased by cross-laminating. There were strong correlations between dynamic MOE by flexural vibration and static bending MOE (correlation coefficient r = 0.919~0.972) or bending MOR (correlation coefficient r = 0.811~0.947) of 3-ply laminated woods, and the correlation coefficient were higher in parallel-laminated woods than in cross-laminated woods. It indicated that static bending strength performances were able to be estimated from dynamic MOE by flexural vibration. Also, close correlations between the reciprocal of dynamic MOE by flexural vibration and initial compliance at 0.008 h of 3-ply laminated woods were found (correlation coefficient r = 0.873~0.991). However, the correlation coefficient between the reciprocal of dynamic MOE and creep compliance at 168 h of 3-ply laminated woods was considerably lower than those between dynamic MOE and initial compliance, and it was hard to estimate creep compliance with a high accuracy from dynamic MOE due to the variation of creep deformation.

• Journal of the Korean Wood Science and Technology
• /
• 제32권3호
• /
• pp.8-14
• /
• 2004

Nondestructive evaluation (NDE) technique method using a resonance frequency mode was carried out for woodceramics produced at different carbonizing temperatures (600℃, 800℃, 1000℃, 1200℃, 1500℃) at the phenol resin impregnation rate of 70%, for three kinds of species (Pinus densifora, Pinus koraiensis, Larix leptolepis), respectively. There was a poor relationship between density and static bending MOR. However, close correlations were found between dynamic MOE_d and static bending MOR, and between static MOEs and MOR. Especially, the correlation coefficient was highest between MOE_d and static bending MOR. Therefore, the MOE_d using the resonance frequency mode is useful as a NDE method for predicting the MOR of woodceramics produced at different carbonizing temperatures.

• Journal of the Korean Wood Science and Technology
• /
• 제49권5호
• /
• pp.504-513
• /
• 2021

In this study, cross-laminated wood panels were manufactured with four softwoods and three hardwoods with the goal of efficiently predicting the static strength performance using dynamic modulus of elasticity (MOE) and simultaneously revealing the dynamic performance of cross-laminated wood panels. The effect of the density of the species on the dynamic MOE of the laminated wood panels was investigated. Moreover, the static bending strength performance was predicted nondestructively through the correlation regression between the dynamic MOE and static bending strength performance. For the dynamic MOE, the parallel- and cross-laminated wood panels composed of oriental oak showed the highest value, whereas the laminated wood panels composed of Japanese cedar showed the lowest value. In all types of parallel- and cross-laminated wood panels, the density dependence was confirmed, and the extent of the density dependence was found to be greater in the P_⊥ and C_⊥ types with perpendicular-direction laminae in the faces than in the P_∥ and C_∥ types with longitudinal-direction laminae in the faces. Our findings confirmed that a high correlation exists at a significance level of 1% between the dynamic modulus and static bending modulus or bending strength in all types of laminated wood panels, and that the static bending strength performance can be predicted through the dynamic MOE.

• Journal of the Korean Wood Science and Technology
• /
• 제44권2호
• /
• pp.274-282
• /
• 2016

This aims of this study were to investigate the relationship between non-destructive evaluation (NDE) and actual bending properties of particleboard, and to predict the bending properties of three-layer particleboard. Three kinds of raw materials, i.e. Hinoki (Chamaecyparis obtusa Endl.) strand, knife-milled Douglas-fir (Pseudotsuga manziesii (Mirb) Franco), and hammer-milled matoa (Pometia spp.) obtained from wooden industry, were utilized as furnish for experimental panel with methylene diphenyl diisocyanate (MDI) resin as binder. The NDE test was conducted by hit sounds using an FFT analyzer according to the spectrum peak of wave frequency, while the static bending test was conducted according to JIS A-5908. The results reveal that the dynamic Young's modulus as an NDE test has a potential for being used to predict the elastic bending of particleboards by a specific equation for adjusting its proper values. The values of NDE and static test are significantly different with a deviation range at 3-20%. The bending stiffness of three-layer particleboards manufactured from different wood species is predictable by observing the bending stiffness of two elements based on the thickness of its layers. The predicted values of bending stiffness and static test are significantly different with a deviation range at 5-24%.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1231-1236
• /
• 2007

This study presents the static and dynamic actuating performances of a bending piezoelectric actuator with a thin sandwiched PZT plate under a static load. The stored elastic energy within the actuators which occurs during a curing process is obtained through a flexural bending test. An actuating performance is evaluated in terms of an actuating displacement at the simply supported condition. The results reveal that an actuator that consists of a top layer having a high elastic modulus and a low coefficient of thermal expansion exhibits a better performance than the rest of actuators due to the formation of the large stored elastic energy within the actuator system. When actuators are excited at the alternating current voltage, the effect of PZT ceramic softening results in a slight reduction in the resonance frequency of each actuator as the applied electric field increases. It is thus suggested that the static and dynamic actuating characteristics of bending piezoelectric actuators with a thin sandwiched PZT plate should be simultaneously considered in controlling their performances.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.370.2-370.2
• /
• 2014

본 연구에서는 Bending 시간에 따른 Ti/Au의 전기적 특성 변화에 대한 실험을 진행하였다. 전기적 특성을 평가하기 위해 PET 기판 위에 Ti/Au을 Greek Bridge와 Line Bridge를 합친 Cross Bridge 형태로 증착하였고, Cross Bridge의 Line을 bending하여 시간 경과에 따른 정적인(static) bending 영향을 확인하였다. Bending은 0~100시간까지 진행하였고, Line의 width를 200, 400, 800, $1000{\mu}m$로 가변하여 시간에 따른 비저항의 변화를 측정하였다. 실험결과 Bending시간이 길어짐에 따라 비저항이 감소하였고, 일정시간에서 크게 감소하며, 그 이후에는 포화되는 경향을 보였다. 또한 Width가 증가함에 따라 비저항의 변화가 컸다. 800 um, $1000{\mu}m$에서는 bending 직후 비저항이 초기대비 약 90%까지 떨어졌으며 100시간 후에는 80%까지 감소하였다. 100시간 뒤 Width에 따라 초기대비 비저항이 78%~91%까지 감소하는 것을 확인하였다.