• Journal of Advanced Navigation Technology
• /
• v.11 no.2
• /
• pp.163-169
• /
• 2007

In this paper, we propose a method of trigger pulse generation to capture the image on time by making a synchronization between the x-ray generator and digital x-ray image acquisition system. we designed a wireless trigger pulse generation circuit to make a synchronization between x-ray generator and digital image acquisition system and analysis its performance. When it starts to detect a certain level of x-ray radiation or above from the air, this method starts to generate a ACQ_START signal to indicate the timing for image acquisition starting from digital image acquisition system. Hence, when it starts to detect under certain level of x-ray signal from the air, this method starts to generate a ACC_END signal to indicate the timing for image acquisition stop from digital image acquisition system. Image acquisition is activated only this time between ACQ_START and ACQ_END signal. By doing this wireless detecting of x-ray signal from remote, we can get more accurate timing for capturing the x-ray image and any type of x-ray generator can be connected to digital image acquisition system, regards of wired protocol. This makes easy installation. We could get 3.5 line pair / mm resolution at 20 mAs of x-ray level with resolution chart. This is same or better image comparing to conventional wired result.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.64-70
• /
• 2007

Raising exhaust gas temperature during cold-start period is very crucial to improve emission performance of SI engines because it enhances the performance of catalyst in the early stage of engine start. In this study, control variables such as ignition timing, idle speed actuator(ISA) opening and fuel injection duration were extensively investigated to analyze variations in exhaust gas temperature and engine stability during cranking period. Experimental results showed that spark timing affected engine stability and exhaust gas temperature but the effects were small. On the other hand, shortened injection duration and increased ISA opening led to a significant increase in exhaust gas temperature. Under such conditions, increase in cranking time was also observed, showing that it becomes harder to start the engine. Based on these observations, a pseudo fuel-air ratio, defined as a ratio of fuel injection time to degree of ISA opening, was introduced to analyze the experimental results. In general, decrease in pseudo fuel-air ratio raised exhaust gas temperature with the cost of stable and fast cranking. On the contrary, an optimal range of the pseudo fuel-air ratio was found to be between 0.3 to 0.5 where higher exhaust gas temperatures can be obtained without sacrificing the engine stability.

• Journal of KIISE
• /
• v.42 no.9
• /
• pp.1162-1174
• /
• 2015

These days, the networks have exhibited HBDP (High Bandwidth Delay Product) characteristics. The legacy TCP slowly increases the size of the congestion window and drastically decreases the size of a congestion window. The legacy TCP has been found to be unsuitable for HBDP networks. TCP mechanisms for solving the problems of the legacy TCP can be categorized into the loss-based TCP and the delay-based TCP. Most of the TCP mechanisms use the standard slow start phase, which leads to a heavy packet loss event caused by the overshoot. Also, in the case of congestion avoidance, the loss-based TCP has shown problems of wastage in terms of the bandwidth and RTT (Round Trip Time) fairness. The delay-based TCP has shown a slow increase in speed and low occupancy of the bandwidth. In this paper, we propose a new scheme for improving the over shoot, increasing the speed of the bandwidth and overcoming the bandwidth occupancy and RTT fairness issues. By monitoring the buffer condition in the bottleneck link, the proposed scheme does congestion control and solves problems of slow start and congestion avoidance. By evaluating performance, we prove that our proposed scheme offers better performance in HBDP networks compared to the previous TCP mechanisms.

• Korean Security Journal
• /
• no.35
• /
• pp.7-36
• /
• 2013

Collecting international terrorism database is a challenging task not only for criminal justice personnel but also for criminologists in comparison to the case of common types of crime database. Yet, there has been growing interests and efforts in establishing a comprehensive terrorist events data base in the world. This current study has a goal to introduce an example world terrorism database case developed by START center in the United States. The START center developed the Global Terrorism Database (GTD) on the basis of by the Pinkerton Global Intelligence Service data (PGIS) originally collected by the Pinkerton. Furthermore, The START expended the GTD by collecting data from open source terrorist event data via internet and other resources. In this study, specifically, it describes the development and the nature of the GTD in general and the data collection efforts made by the STATA until today. Finally, this study provides a sketchy of the nature of the GTD data by showing the descriptive statistical analyses and time-series analyses result illustrating distribution of the world terrorism events. The limitation, policy implications and contribution of this study discussed in this paper.

• Journal of Convergence for Information Technology
• /
• v.8 no.1
• /
• pp.301-312
• /
• 2018

The purpose of this study is to propose strategies for enhancing competitiveness through the utilization of policy funds, especially in the start-up companies supported by the Korea Credit Guarantee Fund. And then, the Korea Credit Guarantee Fund should develop 'user-centered policy funding model' in order to increase start-up's utilization of policy fund and support start-ups that are supported in the long run. The competitiveness of domestic start-up companies has been strengthened by 'user-centered policy funding model' and new innovations have been introduced through 'Living Lab', an open innovation. But, in order to overcome the limitation of reaching the stage of commercialization, the 'user-centered policy funding model' proposed in this study enables start-ups to be the subject of actual policy funding, and also allows users to freely apply for necessary funding at any time. Therefore, the Korea Credit Guarantee Fund has a significance in suggesting 'user-centered policy funding model' as a support model to be customized. However, since SMEs recognize the actual situation and limit acceptance of all the difficulties, the systematic analysis of the actual situation of the policy funds of the start-up by the credit guarantee fund and the related support institutions for the scientific approach of the user-oriented policy funding model need.

• Restorative Dentistry and Endodontics
• /
• v.28 no.2
• /
• pp.134-145
• /
• 2003

Mechanical properties and microleakage of two composites [conventional hybrid type DenFil (VERICOM Co., Anyang, Korea) / micro matrix hybrid type Esthet X (Dentsply Caulk, Milford, DE, U.S.A.)] were evaluated to assess whether variable light intensity curing is better than conventional curing technique. Curing was done for 40 seconds in two ways of 2 step soft-start technique and 5 step ramping technique. Three kinds of light intensities of 50, 100, $200{\;}mW/\textrm{cm}^2$ were initially used for 10, 20, 30 seconds each and the maximum intensity of $600 {\;}mW/\textrm{cm}^2$ was used for the rest of curing time in a soft-start curing tech nique. In a ramping technique, curing was done with the same initial intensities and the light intensity was increased 5 times with the same rate to the maximum intensity of $600{\;}mW/\textrm{cm}^2$. After determining conditions that showed no different mechanical properties with conventional technique, Esthet X composite was filled in a class V cavity, which dimension was $4{\times}3{\times}1.5{\;}mm$ and cured under those conditions. Microleakage was evaluated in two ways of dye penetration and maximum gap estimation through SEM observation. ANOVA and Spearman's rho test were used to confirm any statistical significance among groups. The results were as follows : 1 Several curing conditions of variable light intensities resulted in the similar mechanical properties with a conventional continuous curing technique, except conditions that start curing with an initial light intensity of $50{\;}mW/\textrm{cm}^2$. 2. Conventional and ramping techniques were better than soft-start technique in mechanical properties of microhardness and compressive strength. 3. Soft-start group that started curing with an initial light intensity of $100{\;}mW/\textrm{cm}^2$ for 10 seconds showed the least dye penetration. Soft-start group that started curing with an initial light intensity of $200{\;}mW/\textrm{cm}^2$ for 10 seconds showed the smallest marginal gap, if there was no difference among groups. 4. Soft-start technique resulted in better dye-proof margin than conventional technique(p=0.014) and ramping technique(p = 0.002). 5. There was a very low relationship(p=0.157) between the methods of dye penetration and marginal gap determination through SEM evaluation. From the results of this study, it was revealed that ramping technique would be better than conventional technique in mechanical properties, however, soft-start technique might be better than conventional one in microleakage. It was concluded that much endeavor should be made to find out the curing conditions, which have advantages of both aspects or to solve these kinds of problems through a novel idea of polymerization.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.2
• /
• pp.75-82
• /
• 2007

The purpose of this study was to analyze and compare the effect of gait time on the gait patterns in elderly female OA and non-OA patients. The intensity of the subjects joint pain was surveyed by using WOMAC. Twelve subjects participated in this study. Measurements were taken for every the 10 minutes for 30 minutes after walking by a force plate. The following variables were recorded; double stance support time, Fx, Fy, Fx_time, Fz and so on. From the investigation of these variables the following was observed and concluded. The Fz values for the OA group was 1.01BW at the start and after 30 minutes was 1.04BW on the other hand the non-OA group's Fz1 was 1.08BW and 1.10BW. There was no significant difference calculated between the two groups and at the start and end of the experiment about all the variables. Therefore, it is concluded that there was no negative effect caused by walking for the 30 minutes and that it was an effective way of strengthen both respiratory and muscle function.

• Korean Journal of Applied Biomechanics
• /
• v.28 no.2
• /
• pp.79-85
• /
• 2018

Objective: This study aimed to create a strategic training method to enhance optimal athletic ability using information from 1H to 10H rhythmic units. Method: Top three world class athletes and three national winners of 110-m hurdle finals from the 2010 Daegu International Athletics Competition and 2017 National Athletics Championship, respectively, were selected. To analyze the kinematic variables, Dartfish 9.0 was used for two-dimensional analysis. Results: Regarding the interval time from the start to the finish line, the national athletes took less time during the pure acceleration phase (start to 1H) than the foreign athletes. The horizontal velocity increase was slower after 1H; the national athletes showed a lack of ability to accelerate at the interval phases. Moreover, the hurdle clearance time between phases was longer in the national athletes than in the foreign athletes and lacked consistency. Conclusion: The national athletes lacked the ability to accelerate at the transition, maximum rhythm, rhythm maintenance, and re-acceleration phases and showed a longer hurdle clearance time. If technical improvements and strategic training methods using rhythmic units are applied for hurdling motions, the national athlete's hurdling abilities, performance, and consistency could improve.

• Korean Journal of Applied Biomechanics
• /
• v.12 no.2
• /
• pp.179-195
• /
• 2002

The purpose of this research is to provide a proper model by analyzing the sports biomechanical of physical movements on the basis of the two patterns(open-stance and cross-stance) at the ready-to-start pose. The subjects for this study are composed of five male handball players from P university and five female shooting players from S university. Three-way moving actions at start(right, left, and forward) are recorded with two high-speed video cameras and measured with two Force platforms and a EMG system. Three-dimensional action analyzer, GRF system, and Whole body reaction movement system are used to figure out the moving mechanisms at the start pose. The analytic results of the moving mechanism at the start pose were as follows. 1. Through examining the three-way moving actions at start, I have found the cross-stance pose is better for the moving speed of body weight balance than the open-stance one. 175 degree of knee joint angle at "take-off" and 172 degree of hip joint angle were best for the start pose. 2. The Support time and GRF data shows that the quickest center of gravity shift was occurred when cross-stanced male subjects started to move toward his lefthand side. The quickest male's average supporting time of left and right foot is 0.19${\pm}$0.07 sec., 0.26${\pm}$0.06sec. respectively. The supporting time difference between two feet is 0.07sec. 3. Through analyzing GRF of moving actions at start pose, I have concluded that more than 1550N are overloaded on one foot at the open-stance start, and the overloaded force may cause physical injury. However, at the cross-stance pose, The GRF are properly dispersed on both feet, and maximum 1350N are loaded on one foot.

• Restorative Dentistry and Endodontics
• /
• v.32 no.1
• /
• pp.28-36
• /
• 2007

The purpose of this study was to compare the effect of exponential curing method with conventional curing and soft start curing method on polymerization shrinkage of composite resins. Three brands of composite resins (Synergy Duo Shade, Z250, Filtek Supreme) and three brands of light curing units (Spectrum 800, Elipar Highlight, Elipar Trilight) were used. 40 seconds curing time was given. The shrinkage was measured using linometer for 90 seconds. The effect of time on polymerization shrinkage was analysed by one-way ANOVA and the effect of curing modes and materials on polymerization shrinkage at the time of 90s were analysed by two-way ANOVA. The shrinkage ratios at the time of 20s to 90s were taken and analysed the same way. The results were as follows : 1. All the groups except Supreme shrank almost within 20s Supreme cured by soft start and exponential curing had no further shrinkage after 30s (p < 0.05). 2. Statistical analysis revealed that polymerization shrinkage varied among materials (p = 0.000) and curing modes (p = 0.003). There was no significant interaction between material and curing mode. 3. The groups cured by exponential curing showed the statistically lower polymerization shrinkage at 90s than the groups cured by conventional curing and soft start curing (p < 0.05). 4. The initial shrinkage ratios of soft start and exponential curing were statistically lower than conventional curing (p < 0.05). From this study, the use of low initial light intensities may reduce the polymerization rate and, as a result, reduce the stress of polymerization shrinkage.