• Korean Journal of Metals and Materials
• /
• v.49 no.1
• /
• pp.58-63
• /
• 2011

The grain size and growth direction of a directionally solidified turbine blade were evaluated by the initial nucleation condition at the start block of directional solidification. The initial nucleation condition was controlled by inserting a Ni foil on the directional solidification plate of the directional solidification furnace. Fine grains with good orientation were obtained in the faster cooling condition at the start block. The nucleus number was compared with the cooling rate of the start block by electron back scattered diffraction (EBSD). DSC (differential scanning calorimeter) analysis was performed to compare the melting point and undercooling for nucleation of the coarse nuclei and fine nuclei of the start block. The faster cooling condition at the start block showed more undercooling for nucleation and smaller size of nuclei which resulted in a fine grain with good orientation in the directional turbine blade.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.67-74
• /
• 2001

A synchronized secondaty air injection method has been developed to hydrocarbon emission by injecting secondary air intermittently into exhaust port. The method has been tested in a single cylinder spark-ignition engine operating at cold-steady / cold-start conditions. Effects of air injection timing, intake pressure and engine air-fuel ratio have been investigated at cold-steady condition. Also, hydrocarbon emission and exhaust gas temperature with catalytic conberter are compared with a continuous SAI method and base condition at cold-start condition. Resules show that hydrocarbon reduction rate and exhaust gas temperature are sensitive to the timing of synchronized SAI. At cold-steady condition, HC emission is minimum at engine air-fuel ratio of 10. At cold-start condition, the accumulated hydrocarbon emission during the first 120 s decreases about 56% and 22% with the synchronized and continuous SAI, respectively, compared to that of base condition.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.1063-1066
• /
• 1996

On the prediction of driving performance, an acceleration performance is normally simulated in stall starting condition which is the engine status of full-throttle and high-speed. The lack of transient engine torque data makes the difficulty of predicting an acceleration performance on engine-idle start condition. A experimental equation of transient engine torque is derived from vehicle performance test data. It is applied to simulation the accleration performance prediction on idle starting condition.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.3
• /
• pp.66-72
• /
• 2008

Fuel reforming technology for the fuel cell vehicles could be adopted to internal combustion engine for the reduction of engine out emissions. Since syngas which is reformed from fossil fuel has hydrogen as a major component, it has abilities to enhance the combustion characteristics with wide flammability and high speed flame propagation. In this paper, syngas was feed to 2.0 liter gasoline engine during the cold start and early state of idle condition. Not only cold start HC emission but also $NO_x$ emission could be dramatically reduced due to the fact that syngas has no HC and has nitrogen up to 50% as components. Exhaust gas temperature was lower than that of gasoline feeding condition. Delayed ignition timing, however, resulted in increased exhaust gas temperature approximated to gasoline condition. It is supposed that the usage of syngas in the gasoline internal combustion engine is an effective solution to meet the future strict emission regulations by the reduction of cold start THC and $NO_x$ emissions.

• Journal of Welding and Joining
• /
• v.26 no.2
• /
• pp.92-97
• /
• 2008

In welding of thin plate, some defects such as melt through and unmelted zone occur easily at welding start, however there is a limited study on those problems. Therefore the effects of start block and arc length on melt through and unmelted zone at start were investigated in this study. When start block height was lower than base metal, there was melt through at start. And when the height was even with base metal, no unmelted zone existed. Unmelted zone was increased as start block height increased from 0mm to 0.5mm. However unmelted zone was not much changed as the height increasing from 0.5mm to 1.0mm. When gap existed between start block and base metal, melt through occurred. However, unmelted zone was increased as the contact force of start block on base metal was increased from 0kgf to 7.5kgf. And when arc length was decreased from 3.8mm to 3.0mm, unmelted zone was decreased. It was concluded that the optimum condition to prevent melt through and to minimize unmelted zone would be with start block height 0.25mm, contact force 3.0kgf, and arc length 3.4mm. This optimum condition was applied to the mass production line and resulted in satisfied outcome.

• Korean Journal of Applied Biomechanics
• /
• v.27 no.1
• /
• pp.75-81
• /
• 2017

Objective: The purpose of this study was to compare and analyze the kinematic variables and electromyography (EMG) findings that change with varying characteristics of crouch start and feedback provision, and to provide the fundamental data for record improvement in 400 mH. Method: Four short-distance runners participated in the experiment. The analyzed variables were elapsed time per interval, stride length, and muscle activities in three lower limb muscles. These variables were analyzed by using Kwon3d XP and Noraxon Myoresearch. The participants were subjected to three conditions, including two conditions that relate to the thrusting foot on the rear block and another condition pertinent to feedback provision. Results: In terms of a one-step interval, the elapsed time in condition A was longer than that in condition B, and the one after the feedback was the longest. The stride length of a one-step interval was the longest in condition A. The stride length of a two-step interval was the shortest in condition A. The muscle activity during a one-step interval showed differences in vastus medialis and medial gastrocnemius, with condition A being the highest. Conclusion: When the non-dominant left foot was located at the back, negative results were observed in terms of elapsed time and stride length. Moreover, an imbalance in muscle activity was observed between the left and right feet when the left foot was placed at the back. As a result, significant differences in elapsed time, stride length, and muscle activity were observed depending on the foot placed on the rear block. In conclusion, we identified the characteristics of crouch start in 400 mH, and a specialized program must be suggested.

• Journal of Korean Society for Atmospheric Environment
• /
• v.9 no.2
• /
• pp.160-167
• /
• 1993

As the major methanol fueled vehicle exhaust components, formaldehyde & methanol conversion over the existing commercial 3-way catalyst was examined in a labolatory tains different Ag loadings on commercial 3-way catalyst, and german commercial catalysts for methanol engine exhaust manufactured by a commercial manufacturer. Silver catalysts were prepared by the wet impregnation of silver nitrate solution on commercial 3-way catalyst. These catalysts were characterized with BET Surface area and pore size distribution. In general, the formaldehyde(HCHO) conversion of the tested catalysts was similar to that of methanol$(CH_3OH)$. At 100$^\circ$C, which is equivalent to the cold start condition, 5wt% Ag cat. showed the most excellent HCHO and $CH_3OH$ conversion. The order of activity for conversion of HCHO & $CH_3OH$ to carbon dioxide and water vapor was as follows ; 5wt% Ag/3-way cat.>2wt% Ag/3-way cat.>german cat. front(1) > german cat. rear(2) > 10wt% Ag/3-way cat.> commercial 3-wat catalyst. However there was no significant activity difference between those tested catalysts in the hot run condition of 400$^\circ$C. Therefore, it could be concluded that the Ag-modified 3-way catalyst was the most effective and practical catalyst system which could be capable of removal the HCHO and methanol at the special condition of low temperature such as cold start condition.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.6
• /
• pp.628-633
• /
• 2012

It was found that the pure hydrogen-air pre-mixture was self-ignited at a high compression ratio without any assisting method in room temperature, thus refuting the preconception that compression ignition of hydrogen engine was impossible. Therefore, in order to analyze the correlation of compression ignition condition at cold start with hydrogen HCCI engine clearly, the possibility of compression igniting compression ratio is investigated with the change of equivalence ratio and engine speed, experimentally. As the results, it is confirmed that the possibility of compression-igniting compression ratio at cold start was decreased by increasing equivalence ratio due to decreasing auto-ignition temperature. In addition, it is grasped that the possibility of compression-igniting compression ratio at cold start is decreased around 14.9% by increasing engine speed at same supply energy.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.631-632
• /
• 2006

This paper is written by research for the transient characteristics of the Single-phase Line-start permanent Magnet. The Single-phase Line-start permanent Magnet is most likely to substitute for Single-phase Induction Motor which is used about many appliance currently, because that has good points. For example, It has a Line-start of ability and a High-efficiency. And it need not power convergence device. The rotor of The Single-phase Line-start permanent Magnet has cage-bar with permanent magnet. This motor is started by cage-bar. When it entered synchronous condition, the rotor is rotated by the permanent magnet. But the design of the permanent magnet is very important, because the breaking torque of the permanent magnet interrupt to start a rotor. Finally, if Flux Barrier is not concerned, we do not get result of our object. Therefore this thesis is concerned about Flux Barrier.

• IE interfaces
• /
• v.18 no.1
• /
• pp.73-81
• /
• 2005

Injection molding has been widely used in producing plastic parts in large quantities. However, its productivity mainly depends on the expertise and experience of skilled workers because of the difficulty and complexity to determine a robust injection molding condition which is not influenced by the minor operational variation of an injection molding machine and produces good parts continuously. This study analyzes the defect types of the parts and proposes a support system to assist users in determining the robust process condition. The support system calculates the start condition from the information of an injection mold, the injection molding machine, the resin used, and the part. Through the iterative step which updates the condition using the defect information of the part tested, users can obtain the initial condition which produces the part without any problem for the first time. The support system also assists users in obtaining the robust condition from the initial condition using the technique of experimental design. To prove the validity of the support system, this study implements it in the control panel of the injection molding machine.