• International Journal of Railway
• /
• v.3 no.2
• /
• pp.60-67
• /
• 2010

This paper deals with an experimental study on the wheel flange climbing of railway vehicles, which is a major factor leading to derailment. An experiment is carried out on a 1/5-scale model wheelset of a truck used on a standard-gauge track, which is placed on a roller rig. The lateral external force acting on the wheelset is ramped up until derailment occurs under the condition of a fixed attack angle and wheel-load unbalance ratio. Three parameters, the height of wheel lift, the lateral force, and the wheel load acting on the outer rail, are measured until derailment occurs. From these measurements, it is possible to observe the behavior of the wheelset and to elucidate how the attack angle, the wheel-load unbalance ratio and the lateral external force affect flange-climb derailment. Then, a numerical simulation is carried out using an analytical model based on a single wheelset. As a result, the flange-climb behavior observed in the experiment can be explained theoretically on the bases of the analytical results, although further improvement of the model is desired.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.1009-1011
• /
• 2003

The procurement of mobile microwave scatterometer involve the consideration to ensure vehicle and equipment selection full-filled technical requirement and safety standard in Malaysia. Designing, and modification works involve engineering methodology in determining and selecting a suitable hydraulic telescopic boom that suit a selected vehicle available from the market. The vehicle is also a delivery system for microwave remote sensing equipment and other accessories to any locations in Malaysia. Total loading to be carried by the vehicle is about 4500 kg and its overall weight must be 16,000 kg as recommended by hydraulic telescopic boom manufacturers. The telescopic boom will elevate microwave scatterometer system and antenna to a maximum height of 27 m, and can also be rotated through 360$^{\circ}$. A mechanism is incorporated in the system to enable tracking or monitoring angular movement of the hydraulic telescopic boom when positioned towards required target.

• The Journal of the Acoustical Society of Korea
• /
• v.27 no.8
• /
• pp.403-410
• /
• 2008

The noise problem became more serious by the rapid urban population growth and traffic. This study estimates the noise level considering actual traffic volume and building shape and location. Based on the state of the arts noise level, changing amount of noise that was controlled by the speed control and truck and passenger car restriction is calculated. Some conclusion is found out. The 2-D type more than 3-D type is more than over standard of noise pollution and night time's over rate is larger than day time. And in the case of various solutions are used instead of applying one solution, noise pollution is effectively reduced.

• International Journal of Highway Engineering
• /
• v.17 no.6
• /
• pp.37-45
• /
• 2015

PURPOSES : The purpose of this study is to validate the design criteria of the concrete modular road system, which is a new semi-bridge-type concept road, through a comparison of numerical analysis results and actual loading test results under static axial loads. METHODS : To design the semi-bridge-type modular road, both the bridge design code and the concrete structural design code were adopted. The standard truck load (KL-510) was applied as the major traffic vehicle for the design loading condition. The dimension of the modular slab was designed in consideration of self-weight, axial load, environmental load, and combined loads, with ultimate limit state coefficients. The ANSYS APDL (2010) program was used for case studies of center and edge loading, and the analysis results were compared with the actual mock-up test results. RESULTS : A full-scale mock-up test was successfully conducted. The maximum longitudinal steel strains were measured as about 35 and 83.5 micro-strain (within elastic range) at center and edge loading locations, respectively, under a 100 kN dual-wheel loading condition by accelerating pavement tester. CONCLUSIONS : Based on the results of the comparison between the numerical analysis and the full-scale test, the maximum converted stress range at the edge location is 32~51% of the required standard flexural strength under the two times over-weight loading condition. In the case of edge loading, the maximum converted stresses from the Westergaard equation, the ANSYS APDL analysis, and the mock-up test are 1.95, 1.7, and 2.3 times of that of the center loading case, respectively. The primary reason for this difference is related to the assumption of the boundary conditions of the vertical connection between the slab module and the crossbeam module. Even though more research is required to fully define the boundary conditions, the proposed design criteria for the concrete modular road finally seems to be reasonable.

• Journal of Korean Society of Transportation
• /
• v.27 no.1
• /
• pp.97-105
• /
• 2009

It is expected that logistics standardization have an great effect on industry and national economy due to cost saving and improving efficiency. Therefore all countries of the world make a strenuous effort to take a lead of logistics standardization Despite such efforts of every country, our country remained a lukewarm attitude about logistics standardization. Especially, our country remained a lukewarm attitude about logistics standardization effect quantify. We have to suggest the necessity of standardization and the effect for carrying out logistics standard. So, this study performed literature review and case study for development of effect valuation method. Also, this study developed effect valuation standard for quantifiable standardization effect and drew the effect valuation standard model. First, the measure of preliminary effectiveness was chosen for MOE selection. As a results, vehicle load ratio, delivery cost, keeping space efficiency warehouse automation ratio, etc. were selected. Then, vehicle/truck load ratio, warehouse keeping efficiency, up unloading hour, packaging cost, consistency transportation ratio were chosen for MOE of pallet standardization.

• Journal of Korean Society of Transportation
• /
• v.24 no.5 s.91
• /
• pp.35-44
• /
• 2006

Acceleration and deceleration curves have been used for design purposes worldwide. The curve in design level has been regarded as an single deterministic curve to be used for design of climb lanes. It should be noted that the curve was originally made using ideal driving truck and that the curve is applied during design based on the assumption of no difference between ideal and real driving conditions. However. observations show that aged vehicles and lazy behavioring drivers nay make lower performance of vehicles than the ideal performance. The present paper provides the results of truck speeds at climbing lanes then probabilistic variation of acceleration and deceleration corves. For these purposes. a study about identification of vehicle makers, and weights for trucks at freeway toll gates and then observation of vehicle-following speed were performed. The 85%ile results obtained were compared with the deterministic performance curves of 180, 200, and 220 Ib/hp. It was identified that the performance of 85%ile results obtained from vehicle-following-speed observations were lower than one from deterministic performance curves. From these results, it may be concluded that at the beginning Point of climbing lanes additional $16.19{\sim}67.94m$ is necessary and that at the end point of climbing lanes $53.12{\sim}103.24m$ of extension is necessary.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.269-281
• /
• 2010

The cone penetration test(CPT) has been increasingly used for in situ site characterization. However, the use of CPT is often limited due to specific site conditions depending on the cone size, geometry, and capacity of the CPT system used. In South Korea, it has generally been considered that the CPT could be satisfactorily performed only in soft soils. Louisiana State University/ Louisiana Transportation Research Center has implemented a field-rugged continuous intrusion miniature cone penetration test (CIMCPT) system since the 1990s. The miniature cone penetrometer of the CIMCPT system has a cross-sectional cone area of $2cm^2$ allowing finer soil profiles compared to the standard $10cm^2$. The reduced cross-sectional area also enables a system capacity reduction leading to cost saving and ease in maintenance. In addition, the continuous intrusion mechanism allows fast and economic site investigations. Samsung C&T Corporation has recently implemented a similar CIMCPT system. In this study, case studies on the field application of Samsung CIMCPT system for the last 2 years are presented to illustrate its performance investigation and its usefulness and limitation. Results of the case studies show that the CIMCPT system can be applied to soils with cone tip resistance($q_c$) values up to about 30MPa and allows a reliable and useful way to characterize soft soils. The results also show that the rod buckling limits the investigation depth by the system and the large contact pressure of the CIMCPT truck prevents the use of the system at sites with soft surface soils. According to the results of the case studies, the Samsung CIMCPT system has been being upgraded with a miniature cone with a longer rod, a crawler-type transportation system, a pre-boring system, and so on.

• International Journal of Highway Engineering
• /
• v.15 no.4
• /
• pp.177-186
• /
• 2013

PURPOSES: The purpose of this study theoretically reviews vertical grade deriving process in super high speed environment and compares overseas design criteria with Domestic Standardization also draws suitable vertical grade design criteria of high standard for Domestic Circumstances in Korea. METHODS : By researching domestic vehicle registration status, calculating typical vehicle, using Vissim which is traffic simulation program, Speed-distance curve of the vehicle is derived under each design speed condition. Through Speed-distance curve, estimating critical length of grade and considering critical length of grade, maximum longitudinal incline is proposed. RESULTS : The result of domestic vehicle registration status, the typical vehicle for deriving vertical grade is calculated based on gravity horsepower ratio 200 lb/hp. For calculating critical length of grade, according to change speed of uphill entry, speed-distance curve is derived by using Vissim. Critical length of grade is calculated based on design speed 20 km/h criteria which is point of retardation. Estimated critical length of grade is 808 m and based on this result, maximum longitudinal incline was confirmed in the design speed between 130km/h to 140km/h. CONCLUSIONS: The case of the typical vehicle(truck) which is gravity horsepower ratio 200 lb/hp, maximum longitudinal incline 2% is desirable at the super high speed environment in the design speed between 130km/h to 140km/h.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.2
• /
• pp.455-464
• /
• 2013

If North Korea continuously remains an isolated nation without social interaction with South Korea, the gaps in the theoretical and technological status in construction technology become greater between North and South Korea. Therefore if interactions between North and South Korea can be made, there will be significant improvement in infrastructure technological performance can be made(i.e., Reinforced Concrete bridges). This study was performed to compare and analyze data related to the design standards of North Korean RC bridges and to execute a structural analysis based on standard design specifications of RC slab bridges. Especially, basic study of analyzing the influences on design truck loads of North and South Korea was conducted for the purpose of predicting the performance of North Korean RC slab bridges and the safety levels of traveling vehicles in advance. It is expected that the results of this study can be used as fundamental data for the set-up of South-North RC bridge specification when South and North Korea enter a stage of cooperation and interaction between South and North Korea are actively pursued to prepare for reunification.

• International Journal of Highway Engineering
• /
• v.15 no.5
• /
• pp.111-122
• /
• 2013

PURPOSES : The purpose of this system (Rear Lighting System) is to provide illumination for the driver to operate the commercial vehicle safely after dark in highway, to increase the conspicuity of the vehicle, and especially be suggesting the finest observable improvement method, depending on color and pattern of rear lighting system of truck for midnight highway traffic. METHODS : Rear lightning system as an improving way for forward commercial vehicles lighting the securing sight from human factors and the surrounding environment in midnight driving. For this one, basic materials were collected from the data analysis about many types of problems, and filed investigation for establishing Driving Simulator. also taking statistic test to human volunteers after finding recognizable distance of them. RESULTS : As a result, color with the highest visuality is amber followed by green-red-blue as in order for all road types. Especially almost no difference is found between red and green, also when the light is turn off, recognizable distances is wide difference compared to turn on the light. One more thing about study per pattern, upper and entire lighting have similar recognizable distances, but under lighting shows short distance with difficulty securing sight from medians. And straight section shows similar recognizable distances. By finding visuality improvement method depending on color and pattern of supplement taillight, it is expected to suggest quantitative judgement standard for introducing regulation and improvement of supplement taillight. CONCLUSIONS : Night time vehicle conspicuity to the rear is provided by rear position lamps. this study is showed that the color of light ramp is not important to be safe driving, most important is to turn on the light, recognizable distances is big different compared to turn off the rear light, so when the drivng dark in highway, have to turn on the light for reducing risk.